Headlight Relay Circuit
Circuit diagnosis · Vehicles built from Nov 2005
DESCRIPTION
When the light control switch, located on the headlight dimmer switch, is turned to the HEAD position, the headlight relay (marking: HEAD) illuminates the headlights.WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MAIN BODY ECU) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and press the intelligent tester main switch ON.
Select the item below in the ACTIVE TEST and then check that the relay operates.
- Main body ECU:
Item
Test Details: Display (Range)
Diagnostic Note
Head Light
Headlight Relay ON/OFF
-
- OK:
- Headlights (LOW) come on
|
|
||||
| NG | |
| 2. INSPECT FUSE (HEAD LL, HEAD RL) |
Remove the HEAD LL fuse and HEAD RL fuse from the engine room No. 2 relay block.
Measure the resistance of the fuses.
- Standard resistance:
- Below 1 Ω
|
|
||||
| OK | |
| 3. INSPECT HEADLIGHT RELAY (Marking: HEAD) |
![]() ![]() |
Remove the headlight relay from the engine room No. 2 relay block.
Measure the resistance of the relay.
- Standard resistance:
Tester Connection
Specified Condition
3 - 5
10 kΩ or higher
3 - 5
Below 1 Ω
(Battery voltage applied to terminals 1 and 2)
|
|
||||
| OK | |
| 4. INSPECT BULB (HEADLIGHT BULB) |
![]() ![]() |
Remove the headlight bulbs.
Connect the positive (+) lead from the battery to terminal 2 and the negative (-) lead to terminal 1, then check that the bulb illuminates.
- OK:
- Bulb illuminates.
|
|
||||
| OK | |
| 5. CHECK WIRE HARNESS (MAIN BODY ECU - BATTERY) |
Disconnect the E18 main body ECU connector.

Measure the voltage of the wire harness side connectors.
- Standard voltage:
Tester Connection
Specified Condition
E18-20 (HRLY) - Body ground
10 to 14 V
|
|
||||
| OK | |
| 6. CHECK INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU) |
![]() ![]() |
Measure the voltage of the ECU.
- Standard voltage:
Tester Connection
Condition
Specified Condition
E18-20 (HRLY) - Body ground
Light control switch OFF
10 to 14 V
E18-20 (HRLY) - Body ground
Light control switch ON (HEAD)
Below 1 V
|
|
||||
| OK | ||
| ||
| 7. CHECK WIRE HARNESS (DIMMER SWITCH - MAIN BODY ECU AND BODY GROUND) |
Disconnect the E20 main body ECU connector.
Disconnect the E15 headlight dimmer switch connector.


Measure the resistance of the wire harness side connectors.
- Standard resistance:
for LH side Tester Connection
Specified Condition
E20-12 (HEAD) - E15-20 (H)
Below 1 Ω
E20-12 (HEAD) or E15-20 (H) - Body ground
10 kΩ or higher
for RH side Tester Connection
Specified Condition
E20-12 (HEAD) - E15-11 (H)
Below 1 Ω
E20-12 (HEAD) or E15-11 (H) - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 8. INSPECT HEADLIGHT DIMMER SWITCH |
![]() ![]() |
Remove the E15 headlight dimmer switch.
Measure the resistance of the switch.
- Standard resistance:
for LH side Tester Connection
Switch Condition
Specified Condition
18 (T) - 12 (EL)
Light control switch TAIL
Below 1 Ω
18 (T) - 12 (EL)
Light control switch OFF
10 kΩ or higher
20 (H) - 12 (EL)
Light control switch HEAD
Below 1 Ω
20 (H) - 12 (EL)
Light control switch OFF
10 kΩ or higher
16 (HL) - 12 (EL)
Dimmer switch LOW
Below 1 Ω
16 (HL) - 12 (EL)
Dimmer switch HIGH
10 kΩ or higher
for RH side Tester Connection
Switch Condition
Specified Condition
13 (T) - 19 (EL)
Light control switch TAIL
Below 1 Ω
13 (T) - 19 (EL)
Light control switch OFF
10 kΩ or higher
11 (H) - 19 (EL)
Light control switch HEAD
Below 1 Ω
11 (H) - 19 (EL)
Light control switch OFF
10 kΩ or higher
15 (HL) - 19 (EL)
Dimmer switch LOW
Below 1 Ω
15 (HL) - 19 (EL)
Dimmer switch HIGH
10 kΩ or higher
|
|
||||
| OK | ||
| ||




