Headlight (HI-BEAM) Circuit
Circuit diagnosis · Vehicles built from Nov 2005
DESCRIPTION
The main body ECU receives headlight (HIGH) switch information from the headlight dimmer switch, and controls the headlight dimmer relay (marking: DIM).WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK HEADLIGHT |
Check that the headlights (Low) come on when the light control switch is in the HEAD position.
- OK:
- Headlights (Low) come on.
|
|
||||
| OK | |
| 2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MAIN BODY ECU) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and press the intelligent tester main switch ON.
Select the item below in the ACTIVE TEST and then check the relay operates.
Main body ECU Item
Test Details
Diagnostic Note
Headlight Hi
Turn headlight dimmer switch to HI position:
ON / OFF
-
- OK:
- Headlights (LOW) comes on.
|
|
||||
| NG | |
| 3. INSPECT FUSE (HEAD LH, HEAD RH) |
Remove the HEAD LH and HEAD RH fuses from the engine room No. 2 relay block.
Measure the resistance of the fuses.
- Standard resistance:
- Below 1 Ω
|
|
||||
| OK | |
| 4. INSPECT HEADLIGHT DIMMER RELAY (Marking: DIM) |
![]() ![]() |
Remove the headlight dimmer relay from the engine room No. 2 relay block.
Measure the resistance of the relay.
- Standard resistance:
Tester Connection
Specified Condition
3 - 5
10 kΩ or higher
3 - 5
Below 1 Ω
(Battery voltage applied to terminals 1 and 2)
|
|
||||
| OK | |
| 5. INSPECT HEADLIGHT BULB (HI-BEAM) |
![]() ![]() |
Remove the headlight bulbs (Hi-beam).
Connect the positive (+) lead from the battery to terminal 2 and the negative (-) lead to terminal 1, then check that the bulb illuminates.
- OK:
- Bulb illuminates.
|
|
||||
| OK | |
| 6. CHECK WIRE HARNESS (MAIN BODY ECU - BATTERY) |
![]() ![]() |
Disconnect the E19 main body ECU connector.
Measure the voltage of the wire harness side connector.
- Standard voltage:
Tester Connection
Condition
Specified Condition
E19-3 (DIM) - Body ground
Light control switch HEAD
10 to 14 V
|
|
||||
| OK | |
| 7. CHECK WIRE HARNESS (HEADLIGHT DIMMER RELAY - BATTERY) |
![]() ![]() |
Remove the headlight dimmer relay from the engine room No. 2 relay block.
Measure the voltage of the relay block.
- Standard resistance:
Tester Connection
Condition
Specified Condition
Relay block No. 2 headlight dimmer relay terminal 3 - Body ground
Light control switch HEAD
10 to 14 V
|
|
||||
| OK | |
| 8. CHECK WIRE HARNESS (HEADLIGHT DIMMER RELAY AND BODY GROUND - BULB) |


Remove the headlight dimmer relay from the engine room No. 2 relay block.
Disconnect the A19 and A34 headlight (Hi-beam) bulb connectors.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
Relay block No. 2 headlight dimmer relay terminal 5 - A19-2
Below 1 Ω
Relay block No. 2 headlight dimmer relay terminal 5 or A19-2 - Body ground
10 kΩ or higher
Relay block No. 2 headlight dimmer relay terminal 5 - A34-2
Below 1 Ω
Relay block No. 2 headlight dimmer relay terminal 5 or A34-2 - Body ground
10 kΩ or higher
A19-1 - Body ground
Below 1 Ω
A34-1 - Body ground
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 9. INSPECT HEADLIGHT DIMMER SWITCH |
![]() ![]() |
Remove the headlight dimmer switch.
Measure the resistance of the switch.
- Standard resistance:
for LH side Tester Connection
Condition
Specified Condition
20 (H) - 12 (EL)
Light control switch HEAD
Below 1 Ω
11 (HU) - 12 (EL)
Headlight dimmer switch HIGH
Below 1 Ω
11 (HU) - 12 (EL)
Headlight dimmer switch LOW
10 kΩ or higher
17 (HF) - 12 (EL)
Headlight dimmer switch FLASH
Below 1 Ω
17 (HF) - 12 (EL)
Headlight dimmer switch except FLASH
10 kΩ or higher
for RH side Tester Connection
Condition
Specified Condition
11 (H) - 19 (EL)
Light control switch HEAD
Below 1 Ω
20 (HU) - 19 (EL)
Headlight dimmer switch HIGH
Below 1 Ω
20 (HU) - 19 (EL)
Headlight dimmer switch LOW
10 kΩ or higher
14 (HF) - 19 (EL)
Headlight dimmer switch FLASH
Below 1 Ω
14 (HF) - 19 (EL)
Headlight dimmer switch except FLASH
10 kΩ or higher
|
|
||||
| OK | |
| 10. CHECK WIRE HARNESS (MAIN BODY ECU - HEADLIGHT DIMMER SWITCH) |


Disconnect the E15 headlight dimmer switch connector.
Disconnect the E18 and E20 main body ECU connectors.
Disconnect the IJ instrument panel junction block connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
for LH side Tester Connection
Specified Condition
E20-12 (HEAD) - E15-20 (H)
Below 1 Ω
E20-12 (HEAD) or E15-20 (H) - Body ground
10 kΩ or higher
E18-22 (HF) - E15-17 (HF)
Below 1 Ω
E18-22 (HF) or E15-17 (HF) - Body ground
10 kΩ or higher
IJ-4 (HU) - E15-11 (HU)
Below 1 Ω
IJ-4 (HU) or E15-11 (HU) - Body ground
10 kΩ or higher
for RH side Tester Connection
Specified Condition
E20-12 (HEAD) - E15-11 (H)
Below 1 Ω
E20-12 (HEAD) or E15-11 (H) - Body ground
10 kΩ or higher
E18-22 (HF) - E15-14 (HF)
Below 1 Ω
E18-22 (HF) or E15-14 (HF) - Body ground
10 kΩ or higher
IJ-4 (HU) - E15-20 (HU)
Below 1 Ω
IJ-4 (HU) or E15-20 (HU) - Body ground
10 kΩ or higher
|
|
||||
| OK | ||
| ||





