2005-2008 RAV4 · Service Manual ENGINE

ON-VEHICLE INSPECTION

Inspection · Vehicles built from Nov 2005

HINT:
The type of ignition switch on this model differs according to the specifications of the vehicle. For the expressions used in this section, refer to the "EXPRESSIONS OF IGNITION SWITCH" precaution (Click here).


INSPECT ENGINE COOLANT

INSPECT ENGINE OIL

INSPECT BATTERY

INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
  1. Remove the air cleaner cap.

  1. Remove the air filter element.

  1. Visually check that the air filter is not excessively damaged or oily.
    If necessary, replace the air cleaner filter element sub-assembly.


INSPECT SPARK PLUG

INSPECT FAN AND GENERATOR V BELT

HINT:
You do not need to check the belt deflection because the auto tensioner has been adopted.


INSPECT IGNITION TIMING

NOTICE:
  1. Turn all the electrical systems and the A/C OFF.
  2. Inspect the ignition timing with the cooling fan OFF.
  3. When checking the ignition timing, shift the transmission to the neutral position.

  1. Warm up and stop the engine.

  1. B127990E01
    When using intelligent tester:

    1. Connect the intelligent tester to the DLC3.

    2. Allow the engine to idle.

    3. Select the following menu items:
      Powertrain / Engine and ECT / Data List / IGN Advance.

    4. Read IGN Advance to check the ignition timing.

      Standard ignition timing:
      5 to 15° BTDC @ idle

    5. Check that the ignition timing advances immediately when the engine speed is increased.

    6. Turn the ignition switch off.

    7. Disconnect the intelligent tester from the DLC3.

  1. When not using intelligent tester:

    1. Remove the No. 1 engine cover (Click here).

    2. A112264
      Open the ignition cover located to the right of the No. 4 ignition coil.

    3. Pull out the wire harness from the IG cover.

    4. Connect a timing light to the wire harness.

      NOTICE:
      Use a timing light that detects the first signal.

    5. H100769E05
      Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
      SST
      09843-18040  

    6. Allow the engine to idle and check the ignition timing.

      Standard ignition timing:
      8 to 12° BTDC @ idle

      HINT:
      Run the engine at 1,000 to 1,300 rpm for 5 seconds, then check that the engine speed returns to the idling speed.

    7. Remove SST from the DLC3.

    8. Allow the engine to idle and check the ignition timing.

      Standard ignition timing:
      5 to 15° BTBC

    9. Check that the ignition timing advances immediately when the engine speed is increased.

    10. Turn the ignition switch off.

    11. Remove the timing light.

    12. Close the IG cover.

    13. Install the No. 1 engine cover (Click here).


INSPECT ENGINE IDLE SPEED

  1. B127990E01
    When using intelligent tester:

    1. Turn OFF all the accessories and air conditioning.

    2. Move the shift lever to P or neutral.

    3. Connect the intelligent tester to the DLC3.

    4. Warm up the engine.

    5. Select the tester menus:
      Powertrain / Engine and ECT / Data List / Engine SPD

    6. Read Engine SPD to check the idle speed while the radiator-cooling fan is not rotating.

      Standard idle speed:
      Item
      Specified Condition
      A/T vehicle
      600 to 700 rpm
      M/T vehicle
      650 to 750 rpm

    7. Turn the ignition switch off.

    8. Disconnect the tester from the DLC3.

  1. H100769E32
    When not using intelligent tester:

    1. Turn OFF all the accessories and air conditioning.

    2. Move the shift lever to P or neutral.

    3. Connect SST to 9 (TAC) of the DLC3 terminal, and then connect a tachometer to SST.

      SST
      09843-18030  

    4. Warm up the engine.

    5. Check the idle speed while the radiator-cooling fan is not rotating.

      Standard idle speed:
      Item
      Specified Condition
      A/T vehicle
      610 to 710 rpm
      M/T vehicle
      650 to 750 rpm

    6. Turn the ignition switch off.

    7. Remove the tachometer and disconnect SST from the DLC3.


INSPECT COMPRESSION
  1. Warm up and stop the engine.

  1. Remove the No. 1 engine under cover.

  1. Remove the 4 ignition coils (Click here).

  1. Remove the 4 spark plugs.

  1. Disconnect the 4 fuel injector connectors.

  1. A013304E05
    Set SST and a compression gauge.
    SST
    09992-00500  

  1. Insert the compression gauge into the spark plug hole.

  1. While cranking the engine, measure the compression pressure.

    Standard compression pressure:
    1,300 kPa (13.8 kgf/cm2, 196 psi)

    Minimum pressure:
    1,000 kPa (10 kgf/cm2, 142 psi)

    Standard difference between each cylinder:
    100 kPa (1.0 kgf/cm2, 14 psi)

    NOTICE:
    1. Always use a fully charged battery to obtain an engine speed of 250 rpm or more.
    2. Check the other cylinders' compression pressures in the same way.
    3. This measurement must be done as quickly as possible.

    If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole and inspect again.

    HINT:
    1. If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.
    2. If pressure stays low, a valve may be stuck or seated improperly, or there may be leakage in the gasket.

  1. Connect the 4 fuel injector connectors.

  1. Install the 4 spark plugs.

  1. Install the 4 ignition coils (Click here).

  1. Install the No. 1 engine under cover.


INSPECT CO/HC

HINT:
The ECM properly controls the CO/HC concentration in the emission gas.

  1. Start and warm up the engine.

  1. Run the engine at 2,500 rpm for approximately 180 seconds.

  1. Insert the CO/HC meter testing probe at least 40 cm (1.3 ft.) into the tailpipe while idling.

  1. Inspect the CO/HC concentration while idling and/or at 2,500 rpm.
    If the CO/HC concentration is not as specified, perform troubleshooting.

    HINT:
    See the table below for possible causes, and then inspect and repair the applicable causes if necessary.

    CO
    HC
    Problems
    Causes
    Normal
    High
    Rough idle
    1. Faulty ignition:
    - Incorrect timing
    - Plugs are contaminated, shorted, or gaps are defective
    2. Incorrect valve clearance
    3. Leaks in intake and exhaust valve
    4. Leaks in cylinders
    Low
    High
    Rough idle
    (Fluctuating HC reading)
    1. Vacuum leakage:
    - Ventilation hoses
    - Intake manifold
    - Throttle body
    - Brake booster line
    2. Lean mixture causing misfire
    High
    High
    Rough idle
    (Black smoke from exhaust)
    1. Restricted air filter
    2. Plugged PCV valve
    3. Faulty SFI system:
    - Faulty pressure regulator
    - Faulty engine coolant temperature sensor
    - Faulty mass air flow meter
    - Faulty ECM
    - Faulty injectors
    - Faulty throttle body

← REPAIR (from Nov 2005)COMPONENTS (from Nov 2005) →