2005-2008 RAV4 · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built Nov 2005 – Dec 2006

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2008 from Aug 2008


1. TABLE OF BOLT, SCREW AND NUT

HINT:
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet codes in the table below.


B129999E01

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


3. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY
  1. Remove the instrument panel (Click here).


4. REMOVE STEERING PAD ASSEMBLY

B130245E01
  1. Straighten the front wheels.

  1. Using a T30 "torx" driver, loosen the 2 screws until the groove along each screw circumference catches on the screw case.

  1. B127893E01
    Pull out the steering pad from the steering wheel and support the steering pad with one hand as shown in the illustration.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. Using a screwdriver, disconnect the 2 airbag connectors.

    CAUTION:
    When handling the airbag connector, do not damage the airbag wire harness.

  1. Disconnect the horn connector and remove the steering pad.


5. REMOVE STEERING WHEEL ASSEMBLY
for LHD (Click here)
for RHD (Click here)

6. REMOVE STEERING COLUMN COVER
for LHD (Click here)
for RHD (Click here)

7. REMOVE SPIRAL CABLE SUB-ASSEMBLY

  1. B127900E01
    Rise the steering column cover (upper).

    NOTICE:
    When handling the airbag connector, do not damage the airbag wire harness.

  1. B127901E01
    Detach the 4 clips and remove the column cover (upper).

  1. B127902E01
    Detach the 3 claws and remove the spiral cable.


8. REMOVE HEADLIGHT DIMMER SWITCH ASSEMBLY

9. REMOVE WINDSHIELD WIPER SWITCH ASSEMBLY

10. REMOVE HEATER CONTROL SUB-ASSEMBLY (for Automatic Air Conditioning System)

  1. E118690
    Remove the 2 screws.

  1. Using a screwdriver, detach the 3 clips.

    HINT:
    Tape the screwdriver tip before use.

  1. Connect the connectors and remove the air conditioning control.


11. REMOVE HEATER CONTROL SUB-ASSEMBLY (for Manual Air Conditioning System)

  1. E118688
    Remove the 2 screws.

  1. Using a screwdriver, detach the 3 clips.

    HINT:
    Tape the screwdriver tip before use.

  1. Disconnect the connectors and remove the air conditioning control.


12. REMOVE NO. 1 CONSOLE UPPER PANEL GARNISH

B139541
  1. Using a screwdriver, detach the 4 clips and upper panel garnish.

    HINT:
    Tape the screwdriver tip before use.


13. REMOVE NO. 2 CONSOLE UPPER PANEL GARNISH

B139542
  1. Using a screwdriver, detach the 4 clips and upper panel garnish.

    HINT:
    Tape the screwdriver tip before use.


14. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY

B129883
  1. Remove the shift lever knob.

  1. for Manual Transaxle:
    Using a screwdriver, detach the 2 clips, 4 claws and remove the upper console panel.

    HINT:
    Tape the screwdriver tip before use.

  1. for Automatic Transaxle:
    Using a screwdriver, detach the 2 clips, 4 claws and remove the upper console panel then disconnect the connector.

    HINT:
    Tape the screwdriver tip before use.


15. REMOVE SWITCH BASE

B129882
  1. Detach the 2 clips and 2 claws.

  1. Disconnect the connectors and remove the switch base.


16. REMOVE CONSOLE CUP HOLDER BOX

B129881
  1. Remove the 2 screws.

  1. Detach the 2 clips and remove the cup holder box.


17. REMOVE UPPER REAR CONSOLE PANEL SUB-ASSEMBLY

B129880
  1. Using a screwdriver, detach the 4 clips.

    HINT:
    Tape the screwdriver tip before use.

  1. Disconnect the connector and remove the upper rear console panel.


18. REMOVE CONSOLE REAR END PANEL

B129879
  1. Using a screwdriver, detach the 6 claws and remove the console rear end panel.

    HINT:
    Tape the screwdriver tip before use.


19. REMOVE NO. 1 INSTRUMENT PANEL BRACKET COVER INNER LH

B129877
  1. Detach the 2 claws and remove the instrument panel bracket cover.


20. REMOVE NO. 1 INSTRUMENT PANEL BRACKET COVER INNER RH

B129876
  1. Detach the 2 claws and remove the instrument panel bracket cover.


21. REMOVE REAR CONSOLE BOX SUB-ASSEMBLY

B129878
  1. Remove the console box carpet.

  1. Remove the 2 bolts and 2 screws.

  1. Disconnect the connector and remove the rear console box.


22. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Knee Airbag)

B129996
  1. Remove the 2 screws.

  1. Detach the 2 claws and remove the instrument panel under cover.


23. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Knee Airbag)

B127987
  1. Remove the 4 bolts and driver side knee airbag.

  1. Disconnect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.


24. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (w/o Knee Airbag)

B132919
  1. Remove the 2 screws.

  1. Using a screwdriver, detach the 8 claws and remove the lower instrument panel finish panel.

    HINT:
    Tape the screwdriver tip before use.


25. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Knee Airbag)

B129997
  1. Detach the 2 claws and remove the instrument panel under cover.


26. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

B129889E01
  1. Open the glove compartment door.

  1. Detach the claw from the glove compartment door stopper.

  1. While pushing in the sides of the glove compartment door as indicated by the arrows in the illustration, open the door to release it from the 2 stoppers.

  1. B129888
    Open the door until it is horizontal.

  1. B129888
    Pull the glove compartment door toward the rear of the vehicle to detach the 2 hinges and remove the glove compartment door.


27. REMOVE NO. 1 SWITCH HOLE BASE

B129875
  1. Using a screwdriver, detach the 4 clips.

  1. Disconnect the connectors and remove the switch hole base.


28. REMOVE INSTRUMENT PANEL SAFETY PAD COVER (for LHD)

B132920
  1. Using a screwdriver, detach the 4 claws and remove the instrument panel safety pad cover.

    HINT:
    Tape the screwdriver tip before use.


29. REMOVE INSTRUMENT PANEL BOX

B129874
  1. Remove the screw.

  1. Using a screwdriver, detach the 6 clips and remove the instrument panel box.

    HINT:
    Tape the screwdriver tip before use.


30. REMOVE POWER STEERING ECU ASSEMBLY

C128906E01
  1. Disconnect the connectors.

  1. Remove the 3 nuts and ECU.


31. REMOVE NO. 6 HEATER TO REGISTER DUCT ASSEMBLY (w/ Cool Box)

B139535
  1. Remove the 2 screws and duct.


32. REMOVE LOWER INSTRUMENT PANEL
  1. Remove the 2 bolts, 3 screws and 2 clips.

  1. Disconnect the connectors and clamps and remove the lower instrument panel.

    B129871

← COMPONENTS (from Aug 2008)REMOVAL (Jan 2007 – Jul 2008) →