2005-2008 RAV4 · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built from Aug 2008

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2008 from Aug 2008


1. TABLE OF BOLT, SCREW AND NUT

HINT:
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet codes in the table below.


B208881E01

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


3. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY
  1. Remove the instrument panel (Click here).


4. REMOVE STEERING COLUMN COVER
  1. for LHD:
    Remove the steering column cover (Click here).

  1. for RHD:
    Remove the steering column cover (Click here).


5. REMOVE SPIRAL CABLE SUB-ASSEMBLY

  1. B127900E01
    Rise the steering column cover (upper).

    NOTICE:
    When handling the airbag connector, do not damage the airbag wire harness.

  1. B127901E01
    Detach the 4 clips and remove the column cover (upper).

  1. B127902E01
    Detach the 3 claws and remove the spiral cable.


6. REMOVE COMBINATION SWITCH ASSEMBLY

  1. C128800
    Detach the clamp shown in the illustration and remove the combination switch from the steering column.


7. REMOVE HEATER CONTROL SUB-ASSEMBLY (for Automatic Air Conditioning System)

  1. E118690
    Remove the 2 screws.

  1. Using a screwdriver, detach the 3 clips.

    HINT:
    Tape the screwdriver tip before use.

  1. Connect the connectors and remove the air conditioning control.


8. REMOVE HEATER CONTROL SUB-ASSEMBLY (for Manual Air Conditioning System)

  1. E118688
    Remove the 2 screws.

  1. Using a screwdriver, detach the 3 clips.

    HINT:
    Tape the screwdriver tip before use.

  1. Disconnect the connectors and remove the air conditioning control.


9. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY

  1. B210121
    for Manual Transaxle:
    Twist the shift lever knob in the direction indicated by the arrow and remove it.

  1. B208597
    for Automatic Transaxle:
    Twist the shift lever knob in the direction indicated by the arrow and remove it.


10. REMOVE NO. 1 CONSOLE UPPER PANEL GARNISH

  1. B208598E01
    Place protective tape as shown in the illustration.

  1. Using a moulding remover, detach the 4 clips and remove the upper panel garnish.


11. REMOVE NO. 2 CONSOLE UPPER PANEL GARNISH

  1. B208599E01
    Place protective tape as shown in the illustration.

  1. Using a moulding remover, detach the 4 clips and remove the upper panel garnish.


12. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY (for Manual Transaxle)

  1. B210294
    Using a screwdriver, detach the 2 clips and 4 claws, and then remove the upper console panel.

    HINT:
    Tape the screwdriver tip before use.


13. REMOVE FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSEMBLY (for Automatic Transaxle)

  1. B208601
    Using a screwdriver, detach the 2 clips and 4 claws, and then remove the floor shift position indicator housing.

    HINT:
    Tape the screwdriver tip before use.

  1. Disconnect the connector.


14. REMOVE SWITCH BASE

  1. B209104
    Detach the 2 clips and 2 claws.

  1. Disconnect the connectors and remove the switch base.


15. REMOVE CONSOLE CUP HOLDER BOX

  1. B129881
    Remove the 2 screws.

  1. Detach the 2 clips and remove the cup holder box.


16. REMOVE UPPER REAR CONSOLE PANEL SUB-ASSEMBLY

  1. B129880
    Using a screwdriver, detach the 4 clips.

    HINT:
    Tape the screwdriver tip before use.

  1. Disconnect the connector and remove the upper rear console panel.


17. REMOVE CONSOLE REAR END PANEL

  1. B129879
    Using a screwdriver, detach the 6 claws and remove the console rear end panel.

    HINT:
    Tape the screwdriver tip before use.


18. REMOVE NO. 1 INSTRUMENT PANEL BRACKET COVER INNER LH

B129877
  1. Detach the 2 claws and remove the instrument panel bracket cover.


19. REMOVE NO. 1 INSTRUMENT PANEL BRACKET COVER INNER RH

B129876
  1. Detach the 2 claws and remove the instrument panel bracket cover.


20. REMOVE CONSOLE BOX CARPET

  1. B208602
    Remove the console box carpet.


21. REMOVE REAR CONSOLE BOX SUB-ASSEMBLY

  1. B208604
    Remove the 2 bolts and detach the wire harness clamp.

  1. B208603
    Remove the 2 screws.

  1. Disconnect the connector and remove the rear console box.


22. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL

B132919
  1. Remove the 2 screws.

  1. Using a screwdriver, detach the 8 claws and remove the lower instrument panel finish panel.

    HINT:
    Tape the screwdriver tip before use.


23. REMOVE FRONT DOOR SCUFF PLATE LH

  1. B129699
    Using a screwdriver, detach the 10 claws and remove the scuff plate.

    HINT:
    Tape the screwdriver tip before use.


24. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.


25. REMOVE COWL SIDE TRIM BOARD LH

B129697
  1. Remove the cap nut.

  1. Using a screwdriver, detach the 3 claws and remove the trim board.

    HINT:
    Tape the screwdriver tip before use.


26. REMOVE COWL SIDE TRIM BOARD RH

HINT:
Use the same procedures described for the LH side.


27. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

B129997
  1. Detach the 3 claws and remove the instrument panel under cover.


28. REMOVE NO. 1 SWITCH HOLE BASE

B208358
  1. Using a screwdriver, detach the 4 clips.

    HINT:
    Tape the screwdriver tip before use.

  1. Disconnect the connectors and remove the switch hole base.


29. REMOVE INSTRUMENT PANEL BOX

B129874
  1. Remove the screw.

  1. Using a screwdriver, detach the 6 clips and remove the instrument panel box.

    HINT:
    Tape the screwdriver tip before use.


30. REMOVE POWER STEERING ECU ASSEMBLY

C128906E01
  1. Disconnect the connectors.

    NOTICE:
    Be sure to release the lock of the connector as shown in the illustration.

  1. Remove the 3 nuts and ECU.


31. REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

  1. B209137
    Detach the 3 claws and remove the hood lock control lever.


32. REMOVE LOWER INSTRUMENT PANEL

  1. Remove the 4 bolts, 2 screws and 2 clips.

    B208367E02

  1. Detach the claws and remove the DLC3.

  1. for Automatic Air Conditioning System:
    Disconnect the connector and remove the cooler thermistor hose.

  1. w/ Illumination:
    Disconnect the connectors.

  1. Disconnect the connectors, detach the clamps and remove the lower instrument panel.

← REMOVAL (Jan 2007 – Jul 2008)DISASSEMBLY (Nov 2005 – Jul 2008) →