TERMINALS OF ECU
System information · Vehicles built Nov 2005 – Dec 2006
Versions by build date: Nov 2005 – Dec 2006 from Jan 2007
| CHECK ENGINE SWITCH |


Disconnect the E31 switch connector.
Measure the resistance of the wire harness side connector.
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
GND (E31-5) - Body ground
BR - Body ground
Ground
Always
Below 1 Ω
- If the result is not as specified, there may be a malfunction on the wire harness side.
- If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the E31 switch connector.
Measure the resistance and voltage of the connector.
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
AGND (E31-8) - Body ground
R - Body ground
Ground
Always
Below 1 Ω
VC5 (E31-14) - AGND (E31-8)
BR - R
Power supply
Engine immobiliser system is set
(key is not in cabin)
Below 1 V
Press ignition switch*
4.6 to 5.4 V
CODE (E31-10) - AGND (E31-8)
L - R
Demodulated signal of key code data
Engine immobiliser system is set (key is not in cabin)
Below 1 V
Ignition switch pressed and key held close to ignition switch*
Pulse generation
(see waveform 1)
TXCT (E31-9) - AGND (E31-8)
W - R
Key code output signal
Engine immobiliser system is set (key is not in cabin)
Below 1 V
Ignition switch pressed and key held close to ignition switch*
Pulse generation
(see waveform 2)
- HINT:
- *: Remove the key's battery before performing this inspection.
- If the result is not as specified, the switch may have a malfunction.
Using an oscilloscope, check the waveform 1.

Waveform 1 (Reference): Item
Content
Symbols (Terminal No.)
CODE (E31-10) - AGND (E31-8)
Tool Setting
2 V/DIV., 20 msec./DIV.
Condition
Ignition switch pressed and key held close to ignition switch*
- HINT:
- *: Remove the key's battery before performing this inspection.
Using an oscilloscope, check the waveform 2.

Waveform 2 (Reference): Item
Content
Symbols (Terminal No.)
TXCT (E31-9) - AGND (E31-8)
Tool Setting
2 V/DIV., 20 msec./DIV.
Condition
Ignition switch pressed and key held close to ignition switch*
- HINT:
- *: Remove the key's battery before performing this inspection.
| CHECK ECU AGGREGATION BOX (CERTIFICATION ECU) |


Disconnect the E63 ECU connector.
Measure the resistance and voltage of the wire harness side connector.
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
E (E63-17) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
+B1 (E63-1) - E (E63-17)
R - W-B
+B power supply
Always
9 to 14 V
IG (E63-18) - E (E63-17)
B - W-B
Ignition power supply
Ignition switch off
Below 1 V
- If the result is not as specified, there may be a malfunction on the wire harness side.
- If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the E63 connector.
Measure the resistance and voltage of the connector.
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
AGND (E63-40) - Body ground
BR - Body ground
Ignition switch ground
Always
Below 1 Ω
VC5 (E63-30) - AGND (E63-40)
R - BR
Ignition switch power supply
Engine immobiliser system is set (key is not in cabin)
Below 1 V
Ignition switch pressed*
4.6 to 5.4 V
CODE (E63-9) - AGND (E63-40)
L - B
Ignition switch code input
Engine immobiliser system is set (key is not in cabin)
Below 1 V
Ignition switch pressed and key held close to ignition switch*
Pulse generation
(see waveform 1)
TXCT (E63-8) - AGND (E63-40)
W - B
Ignition switch TX output
Engine immobiliser system is set (key is not in cabin)
Below 1 V
Ignition switch pressed and key held close to ignition switch*
Pulse generation
(see waveform 2)
- HINT:
- *: Remove the key's battery before performing this inspection.
- If the result is not as specified, the ECU may have a malfunction.
Using an oscilloscope, check the waveform 1.

Waveform 1 (Reference): Item
Content
Symbols (Terminal No.)
CODE (E63-9) - AGND (E63-40)
Tool Setting
2 V/DIV., 20 msec./DIV.
Condition
Ignition switch pressed and key held close to ignition switch*
- HINT:
- *: Remove the key's battery before performing this inspection.
Using an oscilloscope, check the waveform 2.

Waveform 2 (Reference): Item
Content
Symbols (Terminal No.)
TXCT (E63-8) - AGND (E63-40)
Tool Setting
2 V/DIV., 20 msec./DIV.
Condition
Ignition switch pressed and key held close to ignition switch*
- HINT:
- *: Remove the key's battery before performing this inspection.
| CHECK ID CODE BOX |


Disconnect the E51 box connector.
Measure the resistance and voltage of the wire harness side connector.
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
GND (E51-8) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
+B (E51-1) - GND (E51-8)
R - W-B
+B power supply
Always
9 to 14 V
- If the result is not as specified, there may be a malfunction on the wire harness side.
- If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the E51 box connector.
Measure the voltage of the connector.
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
EFII (E51-5) - GND (E51-8)
LG - W-B
ECM input signal
Ignition switch off
Below 1 V
Ignition switch on (IG)
Pulse generation (see waveform 1)
EFIO (E51-6) - GND (E51-8)
P - W-B
ECM output signal
Ignition switch off
Below 1 V
Ignition switch on (IG)
Pulse generation (see waveform 2)
- If the result is not as specified, the box may have a malfunction.
- If the result is not as specified, the box may have a malfunction.
Using an oscilloscope, check the waveform 1.

Waveform 1 (Reference): Item
Content
Symbols (Terminal No.)
EFII (E51-5) - GND (E51-8)
Tool Setting
10 V/DIV., 100 msec./DIV.
Condition
Ignition switch on (IG)
Using an oscilloscope, check the waveform 2.

Waveform 2 (Reference): Item
Content
Symbols (Terminal No.)
EFIO (E51-6) - GND (E51-8)
Tool Setting
10 V/DIV., 100 msec./DIV.
Condition
Ignition switch on (IG)
| CHECK STEERING LOCK ACTUATOR (STEERING LOCK ECU) |


Disconnect the E6 ECU connector.
Measure the resistance and voltage of the wire harness side connector.
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
SGND (E6-2) - Body ground
BR - Body ground
Ground
Always
Below 1 Ω
GND (E6-1) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
B (E6-7) - Body ground
L - Body ground
+B power supply
Always
9 to 14 V
IG2 (E6-6) - Body ground
B - Body ground
Ignition power supply
Ignition switch off
Below 1 V
Ignition switch on (IG)
9 to 14 V
- If the result is not as specified, there may be a malfunction on the wire harness side.
- If the result is not as specified, there may be a malfunction on the wire harness side.
| CHECK ECM (for 1AZ-FE) |


Measure the resistance and voltage of the wire harness side connector.
If the result is not as specified, there may be a malfunction in the wire harness.Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
EOM (A12-9) - Body ground
V - Body ground
Ground
Always
Below 1 Ω
IMI (A12-11) - EOM (A12-9)
P - V
Transponder key ECU input signal
Ignition switch off
Below 1 V
Ignition switch on (IG)
Pulse generation (see waveform 1)
IMO (A12-10) - EOM (A12-9)
LG - V
Transponder key ECU output signal
Ignition switch off
Below 1 V
Ignition switch on (IG)
Pulse generation (see waveform 2)
Using an oscilloscope, check the waveform 1.

Waveform 1 (Reference): Item
Content
Symbols (Terminal No.)
IMI (A12-11) - EOM (A12-9)
Tool Setting
10 V/DIV., 500 msec./DIV.
Condition
Ignition switch on (IG)
Using an oscilloscope, check the waveform 2.

Waveform 2 (Reference): Item
Content
Symbols (Terminal No.)
IMO (A12-10) - EOM (A12-9)
Tool Setting
10 V/DIV., 500 msec./DIV.
Condition
Ignition switch on (IG)
| CHECK ECM (for 2AD-FHV, 2AD-FTV) |


Measure the resistance and voltage of the wire harness side connector.
If the result is not as specified, there may be a malfunction in the wire harness.Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
EOM (A12-37) - Body ground
V - Body ground
Ground
Always
Below 1 Ω
IMI (A12-16) - EOM (A12-37)
P - V
Transponder key ECU input signal
Ignition switch off
Below 1 V
Ignition switch on (IG)
Pulse generation (see waveform 1)
IMO (A12-15) - EOM (A12-37)
LG - V
Transponder key ECU output signal
Ignition switch off
Below 1 V
Ignition switch on (IG)
Pulse generation (see waveform 2)
Using an oscilloscope, check the waveform 1.

Waveform 1 (Reference): Item
Content
Symbols (Terminal No.)
IMI (A12-16) - EOM (A12-37)
Tool Setting
10 V/DIV., 500 msec./DIV.
Condition
Ignition switch on (IG)
Using an oscilloscope, check the waveform 2.

Waveform 2 (Reference): Item
Content
Symbols (Terminal No.)
IMO (A12-15) - EOM (A12-37)
Tool Setting
10 V/DIV., 500 msec./DIV.
Condition
Ignition switch on (IG)
| CHECK INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU) |




Disconnect the IB, ID, IE and E19 junction block connectors.
Measure the resistance and voltage of the wire harness side connectors.
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
GND1 (IE-17) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
GND2 (E19-4) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
AM1 (E19-1) - Body ground
W -Body ground
+B power supply
Always
9 to 14 V
AM2 (E19-6) - Body ground
W -Body ground
+B power supply
Always
9 to 14 V
SSW1 (E19-10) - Body ground
W -Body ground
Ignition switch
Ignition switch off
10 kΩ or higher
Ignition switch on (IG)
Below 1 Ω
SSW2 (E19-9) - Body ground
B -Body ground
Ignition switch
Ignition switch off
10 kΩ or higher
Ignition switch on (IG)
Below 1 Ω
BECU (IB-30) - Body ground
R - Body ground
+B power supply
Always
9 to 14 V
LIN1 (ID-9) - Body ground
V - Body ground
LIN communication line
Always
10 kΩ or higher
- If the result is not as specified, there may be a malfunction on the wire harness side.
- If the result is not as specified, there may be a malfunction on the wire harness side.