2005-2008 RAV4 · Service Manual SECURITIES

TERMINALS OF ECU

System information · Vehicles built from Jan 2007

Versions by build date: Nov 2005 – Dec 2006 from Jan 2007


CHECK ENGINE SWITCH
B122831E02
  1. Disconnect the E31 switch connector.

  2. Measure the resistance of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    GND (E31-5) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the E31 switch connector.

  4. Measure the resistance and voltage of the connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    AGND (E31-8) - Body ground
    R - Body ground
    Ground
    Always
    Below 1 Ω
    VC5 (E31-14) - AGND (E31-8)
    BR - R
    Power supply
    Engine immobiliser system is set
    (key is not in cabin)
    Below 1 V
    Press ignition switch*
    4.6 to 5.4 V
    CODE (E31-10) - AGND (E31-8)
    L - R
    Demodulated signal of key code data
    Engine immobiliser system is set (key is not in cabin)
    Below 1 V
    Ignition switch pressed and key held close to ignition switch*
    Pulse generation
    (see waveform 1)
    TXCT (E31-9) - AGND (E31-8)
    W - R
    Key code output signal
    Engine immobiliser system is set (key is not in cabin)
    Below 1 V
    Ignition switch pressed and key held close to ignition switch*
    Pulse generation
    (see waveform 2)

    HINT:
    *: Remove the key's battery before performing this inspection.

    1. If the result is not as specified, the switch may have a malfunction.

  5. B130917E01
    Using an oscilloscope, check the waveform 1.
    Waveform 1 (Reference): 
    Item
    Content
    Symbols (Terminal No.)
    CODE (E31-10) - AGND (E31-8)
    Tool Setting
    2 V/DIV., 20 msec./DIV.
    Condition
    Ignition switch pressed and key held close to ignition switch*

    HINT:
    *: Remove the key's battery before performing this inspection.

  6. B130918E01
    Using an oscilloscope, check the waveform 2.
    Waveform 2 (Reference): 
    Item
    Content
    Symbols (Terminal No.)
    TXCT (E31-9) - AGND (E31-8)
    Tool Setting
    2 V/DIV., 20 msec./DIV.
    Condition
    Ignition switch pressed and key held close to ignition switch*

    HINT:
    *: Remove the key's battery before performing this inspection.


CHECK ECU AGGREGATION BOX (CERTIFICATION ECU)
B108931E05
  1. Disconnect the E63 ECU connector.

  2. Measure the resistance and voltage of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E (E63-17) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    +B1 (E63-1) - E (E63-17)
    R - W-B
    +B power supply
    Always
    9 to 14 V
    IG (E63-18) - E (E63-17)
    B - W-B
    Ignition power supply
    Ignition switch off
    Below 1 V
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the E63 connector.

  4. Measure the resistance and voltage of the connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    AGND (E63-40) - Body ground
    BR - Body ground
    Ignition switch ground
    Always
    Below 1 Ω
    VC5 (E63-30) - AGND (E63-40)
    R - BR
    Ignition switch power supply
    Engine immobiliser system is set (key is not in cabin)
    Below 1 V
    Ignition switch pressed*
    4.6 to 5.4 V
    CODE (E63-9) - AGND (E63-40)
    L - B
    Ignition switch code input
    Engine immobiliser system is set (key is not in cabin)
    Below 1 V
    Ignition switch pressed and key held close to ignition switch*
    Pulse generation
    (see waveform 1)
    TXCT (E63-8) - AGND (E63-40)
    W - B
    Ignition switch TX output
    Engine immobiliser system is set (key is not in cabin)
    Below 1 V
    Ignition switch pressed and key held close to ignition switch*
    Pulse generation
    (see waveform 2)

    HINT:
    *: Remove the key's battery before performing this inspection.

    1. If the result is not as specified, the ECU may have a malfunction.

  5. B130917E01
    Using an oscilloscope, check the waveform 1.
    Waveform 1 (Reference): 
    Item
    Content
    Symbols (Terminal No.)
    CODE (E63-9) - AGND (E63-40)
    Tool Setting
    2 V/DIV., 20 msec./DIV.
    Condition
    Ignition switch pressed and key held close to ignition switch*

    HINT:
    *: Remove the key's battery before performing this inspection.

  6. B130918E01
    Using an oscilloscope, check the waveform 2.
    Waveform 2 (Reference): 
    Item
    Content
    Symbols (Terminal No.)
    TXCT (E63-8) - AGND (E63-40)
    Tool Setting
    2 V/DIV., 20 msec./DIV.
    Condition
    Ignition switch pressed and key held close to ignition switch*

    HINT:
    *: Remove the key's battery before performing this inspection.


CHECK ID CODE BOX
B108932E02
  1. Disconnect the E51 box connector.

  2. Measure the resistance and voltage of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    GND (E51-8) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    +B (E51-1) - GND (E51-8)
    R - W-B
    +B power supply
    Always
    9 to 14 V
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the E51 box connector.

  4. Measure the voltage of the connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    EFII (E51-5) - GND (E51-8)
    LG - W-B
    ECM input signal
    Ignition switch off
    Below 1 V
    Ignition switch on (IG)
    Pulse generation (see waveform 1)
    EFIO (E51-6) - GND (E51-8)
    P - W-B
    ECM output signal
    Ignition switch off
    Below 1 V
    Ignition switch on (IG)
    Pulse generation (see waveform 2)
    1. If the result is not as specified, the box may have a malfunction.

  5. B130919E01
    Using an oscilloscope, check the waveform 1.
    Waveform 1 (Reference): 
    Item
    Content
    Symbols (Terminal No.)
    EFII (E51-5) - GND (E51-8)
    Tool Setting
    10 V/DIV., 100 msec./DIV.
    Condition
    Ignition switch on (IG)

  6. B130920E01
    Using an oscilloscope, check the waveform 2.
    Waveform 2 (Reference): 
    Item
    Content
    Symbols (Terminal No.)
    EFIO (E51-6) - GND (E51-8)
    Tool Setting
    10 V/DIV., 100 msec./DIV.
    Condition
    Ignition switch on (IG)


CHECK STEERING LOCK ACTUATOR (STEERING LOCK ECU)
B106649E11
  1. Disconnect the E6 ECU connector.

  2. Measure the resistance and voltage of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    SGND (E6-2) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    GND (E6-1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    B (E6-7) - Body ground
    L - Body ground
    +B power supply
    Always
    9 to 14 V
    IG2 (E6-6) - Body ground
    B - Body ground
    Ignition power supply
    Ignition switch off
    Below 1 V
    Ignition switch on (IG)
    9 to 14 V
    1. If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK ECM (for 1AZ-FE, 2AZ-FE)
B116297E03
  1. Measure the resistance and voltage of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    EOM (A12-9) - Body ground
    V - Body ground
    Ground
    Always
    Below 1 Ω
    IMI (A12-11) - EOM (A12-9)
    P - V
    Transponder key ECU input signal
    Ignition switch off
    Below 1 V
    Ignition switch on (IG)
    Pulse generation (see waveform 1)
    IMO (A12-10) - EOM (A12-9)
    LG - V
    Transponder key ECU output signal
    Ignition switch off
    Below 1 V
    Ignition switch on (IG)
    Pulse generation (see waveform 2)
    If the result is not as specified, there may be a malfunction in the wire harness.

  2. B130920E02
    Using an oscilloscope, check the waveform 1.
    Waveform 1 (Reference): 
    Item
    Content
    Symbols (Terminal No.)
    IMI (A12-11) - EOM (A12-9)
    Tool Setting
    10 V/DIV., 500 msec./DIV.
    Condition
    Ignition switch on (IG)

  3. B130919E02
    Using an oscilloscope, check the waveform 2.
    Waveform 2 (Reference): 
    Item
    Content
    Symbols (Terminal No.)
    IMO (A12-10) - EOM (A12-9)
    Tool Setting
    10 V/DIV., 500 msec./DIV.
    Condition
    Ignition switch on (IG)


CHECK ECM (for 2AD-FHV, 2AD-FTV)
B116297E03
  1. Measure the resistance and voltage of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    EOM (A12-37) - Body ground
    V - Body ground
    Ground
    Always
    Below 1 Ω
    IMI (A12-16) - EOM (A12-37)
    P - V
    Transponder key ECU input signal
    Ignition switch off
    Below 1 V
    Ignition switch on (IG)
    Pulse generation (see waveform 1)
    IMO (A12-15) - EOM (A12-37)
    LG - V
    Transponder key ECU output signal
    Ignition switch off
    Below 1 V
    Ignition switch on (IG)
    Pulse generation (see waveform 2)
    If the result is not as specified, there may be a malfunction in the wire harness.

  2. B130920E02
    Using an oscilloscope, check the waveform 1.
    Waveform 1 (Reference): 
    Item
    Content
    Symbols (Terminal No.)
    IMI (A12-16) - EOM (A12-37)
    Tool Setting
    10 V/DIV., 500 msec./DIV.
    Condition
    Ignition switch on (IG)

  3. B130919E02
    Using an oscilloscope, check the waveform 2.
    Waveform 2 (Reference): 
    Item
    Content
    Symbols (Terminal No.)
    IMO (A12-15) - EOM (A12-37)
    Tool Setting
    10 V/DIV., 500 msec./DIV.
    Condition
    Ignition switch on (IG)


CHECK INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU)
E114510E18
B108612E07
  1. Disconnect the IB, ID, IE and E19 junction block connectors.

  2. Measure the resistance and voltage of the wire harness side connectors.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    GND1 (IE-17) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    GND2 (E19-4) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    AM1 (E19-1) - Body ground
    W -Body ground
    +B power supply
    Always
    9 to 14 V
    AM2 (E19-6) - Body ground
    W -Body ground
    +B power supply
    Always
    9 to 14 V
    SSW1 (E19-10) - Body ground
    W -Body ground
    Ignition switch
    Ignition switch off
    10 kΩ or higher
    Ignition switch on (IG)
    Below 1 Ω
    SSW2 (E19-9) - Body ground
    B -Body ground
    Ignition switch
    Ignition switch off
    10 kΩ or higher
    Ignition switch on (IG)
    Below 1 Ω
    BECU (IB-30) - Body ground
    R - Body ground
    +B power supply
    Always
    9 to 14 V
    LIN1 (ID-9) - Body ground
    V - Body ground
    LIN communication line
    Always
    10 kΩ or higher
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

← TERMINALS OF ECU (Nov 2005 – Dec 2006)DIAGNOSIS SYSTEM (from Nov 2005) →