Check CAN Bus Line for Short to +B (LHD Models)
Circuit diagnosis · Vehicles built Nov 2005 – Jul 2008
Versions by build date: Nov 2005 – Jul 2008 from Aug 2008
DESCRIPTION
There may be a short circuit between the CAN bus line and +B when there is resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3.| Symptom |
Trouble Area |
| There is resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of DLC3. |
|
- HINT:
- *1: w/ ABS
- *2: w/ VSC
- *3: for 4WD
- *4: for 2WD with VSC and 4WD
WIRING DIAGRAM




INSPECTION PROCEDURE
- NOTICE:
- Turn the ignition switch off before measuring the resistances of the main wire and the branch wire.
- For Auto:
After the ignition switch is turned off, check that the key reminder warning system is not in operation.
- For Reminder:
After the ignition switch is turned off, check that the key reminder warning system and light reminder buzzer are not in operation.
- Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
- Turn the ignition switch off before measuring the resistances of the main wire and the branch wire.
- HINT:
- Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
| 1. CHECK CAN BUS LINE FOR SHORT TO +B (DLC3 BRANCH WIRE) |
Disconnect the E75 No. 2 junction connector.

Measure the resistance of the DLC3.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E16-6 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E16-14 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | |
| 2. CONNECT CONNECTOR |
Reconnect the E75 No. 2 junction connector.
| NEXT | |
| 3. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 1 JUNCTION CONNECTOR SIDE) |
Disconnect the A51 No. 1 junction connector.

Measure the resistance of the DLC3.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E16-6 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E16-14 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| NG | |
| 4. CONNECT CONNECTOR |
Reconnect the A51 No. 1 junction connector.
| NEXT | |
| 5. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 3 JUNCTION CONNECTOR, NO. 4 JUNCTION CONNECTOR SIDE) |
Disconnect the E77 No. 3 junction connector.

Measure the resistance of the DLC3.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E16-6 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E16-14 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | |
| 6. CONNECT CONNECTOR |
Reconnect the E77 No. 3 junction connector.
| NEXT | |
| 7. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 4 JUNCTION CONNECTOR SIDE) |
Disconnect the E76 No. 4 junction connector.

Measure the resistance of the DLC3.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E16-6 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E16-14 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| NG | |
| 8. CONNECT CONNECTOR |
Reconnect the E76 No. 4 junction connector.
| NEXT | |
| 9. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 3 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY) |
Disconnect the E77 No. 3 junction connector.

Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E77-1 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E77-12 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| NG | |
| 10. CONNECT CONNECTOR |
Reconnect the E77 No. 3 junction connector.
| NEXT | |
| 11. CHECK CAN BUS LINE FOR SHORT TO +B (CENTER AIRBAG SENSOR ASSEMBLY) |
Disconnect the E49 center airbag sensor connector.

Measure the resistance of the DLC3.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E16-6 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E16-14 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | ||
| ||
| 12. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 1 JUNCTION CONNECTOR - BRAKE ACTUATOR) |
- NOTICE:
- For vehicles without ABS, go to "CHECK CAN BUS LINE FOR SHORT TO +B (NO. 1 JUNCTION CONNECTOR - ABS AND TRACTION ACTUATOR)".
Measure the resistance of the wire harness side connectors.

- Standard resistance:
Tester Connection
Condition
Specified Condition
A51-1 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
A51-12 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | |
| 13. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 1 JUNCTION CONNECTOR - ABS AND TRACTION ACTUATOR) |
- NOTICE:
- For vehicles without VSC, go to "CHECK CAN BUS LINE FOR SHORT TO +B (NO. 1 JUNCTION CONNECTOR - ECM)".
Measure the resistance of the wire harness side connectors.

- Standard resistance:
Tester Connection
Condition
Specified Condition
A51-1 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
A51-12 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | |
| 14. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 1 JUNCTION CONNECTOR - ECM) |
Measure the resistance of the wire harness side connectors.

- Standard resistance:
Tester Connection
Condition
Specified Condition
A51-2 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
A51-13 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | ||
| ||
| 15. CONNECT CONNECTOR |
Reconnect the A51 No. 1 junction connector.
| NEXT | |
| 16. CHECK CAN BUS LINE FOR SHORT TO +B (BRAKE ACTUATOR) |
Disconnect the A27 brake actuator (skid control ECU) connector.

Measure the resistance of the DLC3.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E16-6 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E16-14 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | ||
| ||
| 17. CONNECT CONNECTOR |
Reconnect the A51 No. 1 junction connector.
| NEXT | |
| 18. CHECK CAN BUS LINE FOR SHORT TO +B (ABS AND TRACTION ACTUATOR) |
Disconnect the A26 ABS and traction actuator (skid control ECU) connector.

Measure the resistance of the DLC3.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E16-6 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E16-14 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | ||
| ||
| 19. CONNECT CONNECTOR |
Reconnect the A51 No. 1 junction connector.
| NEXT | |
| 20. CHECK CAN BUS LINE FOR SHORT TO +B (ECM) |
Disconnect the A12 ECM connector.

Measure the resistance of the DLC3.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E16-6 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E16-14 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | ||
| ||
| 21. CONNECT CONNECTOR |
Reconnect the E77 No. 3 junction connector.
| NEXT | |
| 22. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 2 JUNCTION CONNECTOR - YAW RATE SENSOR) |
- NOTICE:
- For vehicles without VSC, go to "CHECK CAN BUS LINE FOR SHORT TO +B (NO. 2 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)".
Disconnect the E75 No. 2 junction connector.

Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E75-5 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E75-16 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | |
| 23. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 2 JUNCTION CONNECTOR - STEERING ANGLE SENSOR) |
- NOTICE:
- For vehicles without 2WD with VSC and 4WD, go to "CHECK CAN BUS LINE FOR SHORT TO +B (NO. 2 JUNCTION CONNECTOR - POWER STEERING ECU)".
Measure the resistance of the wire harness side connectors.

- Standard resistance:
Tester Connection
Condition
Specified Condition
E75-7 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E75-18 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | |
| 24. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 2 JUNCTION CONNECTOR - POWER STEERING ECU) |
Measure the resistance of the wire harness side connectors.

- Standard resistance:
Tester Connection
Condition
Specified Condition
E75-6 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E75-17 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | |
| 25. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 2 JUNCTION CONNECTOR - MAIN BODY ECU) |
Measure the resistance of the wire harness side connectors.

- Standard resistance:
Tester Connection
Condition
Specified Condition
E75-8 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E75-19 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | |
| 26. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER) |
Measure the resistance of the wire harness side connectors.

- Standard resistance:
Tester Connection
Condition
Specified Condition
E75-4 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E75-15 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | ||
| ||
| 27. CONNECT CONNECTOR |
Reconnect the E75 No. 2 junction connector.
| NEXT | |
| 28. CHECK CAN BUS LINE FOR SHORT TO +B (YAW RATE SENSOR) |
Disconnect the K6 yaw rate sensor connector.

Measure the resistance of the DLC3.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E16-6 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E16-14 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | ||
| ||
| 29. CONNECT CONNECTOR |
Reconnect the E75 No. 2 junction connector.
| NEXT | |
| 30. CHECK CAN BUS LINE FOR SHORT TO +B (STEERING ANGLE SENSOR) |
Disconnect the E14 steering sensor connector.

Measure the resistance of the DLC3.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E16-6 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E16-14 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | ||
| ||
| 31. CONNECT CONNECTOR |
Reconnect the E75 No. 2 junction connector.
| NEXT | |
| 32. CHECK CAN BUS LINE FOR SHORT TO +B (POWER STEERING ECU) |
Disconnect the E21 power steering ECU connector.

Measure the resistance of the DLC3.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E16-6 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E16-14 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | ||
| ||
| 33. CONNECT CONNECTOR |
Reconnect the E75 No. 2 junction connector.
| NEXT | |
| 34. CHECK CAN BUS LINE FOR SHORT TO +B (MAIN BODY ECU) |
Disconnect the E20 main body ECU connector.

Measure the resistance of the DLC3.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E16-6 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E16-14 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | ||
| ||
| 35. CONNECT CONNECTOR |
Reconnect the E75 No. 2 junction connector.
| NEXT | |
| 36. CHECK CAN BUS LINE FOR SHORT TO +B (AIR CONDITIONING AMPLIFIER) |
Disconnect the E41*1 or E42*2 air conditioning amplifier connector.

- HINT:
- *1: for Automatic air conditioning system.
- *2: for Manual air conditioning system.
- *1: for Automatic air conditioning system.
Measure the resistance of the DLC3.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E16-6 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E16-14 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | ||
| ||
| 37. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 4 JUNCTION CONNECTOR - 4WD CONTROL ECU) |
- NOTICE:
- For vehicles without 4WD, go to "CHECK CAN BUS LINE FOR SHORT TO +B (NO. 4 JUNCTION CONNECTOR - COMBINATION METER ECU)".
Measure the resistance of the wire harness side connectors.

- Standard resistance:
Tester Connection
Condition
Specified Condition
E76-7 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E76-18 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | |
| 38. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 4 JUNCTION CONNECTOR - COMBINATION METER ECU) |
Measure the resistance of the wire harness side connectors.

- Standard resistance:
Tester Connection
Condition
Specified Condition
E76-5 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E76-16 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | |
| 39. CONNECT CONNECTOR |
Reconnect the E76 No. 4 junction connector.
| NEXT | |
| 40. CHECK CAN BUS LINE FOR SHORT TO +B (4WD CONTROL ECU) |
Disconnect the E67 4WD control ECU connector.

Measure the resistance of the DLC3.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E16-6 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E16-14 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | ||
| ||
| 41. CONNECT CONNECTOR |
Reconnect the E76 No. 4 junction connector.
| NEXT | |
| 42. CHECK CAN BUS LINE FOR SHORT TO +B (COMBINATION METER ECU) |
Disconnect the E22 combination meter ECU connector.

Measure the resistance of the DLC3.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E16-6 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E16-14 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | ||
| ||
