Check CAN Bus Line for Short to +B (LHD Models)
Circuit diagnosis · Vehicles built from Aug 2008
Versions by build date: Nov 2005 – Jul 2008 from Aug 2008
DESCRIPTION
There may be a short circuit between the CAN bus line and +B when there is resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3.| Symptom |
Trouble Area |
| There is resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of DLC3. |
|
- HINT:
- *1: w/ Anti-lock Brake System
- *2: w/ Vehicle Stability Control System
- *3: for 4WD
- *4: for 2WD (w/ Vehicle Stability Control System) and 4WD
WIRING DIAGRAM




INSPECTION PROCEDURE
- NOTICE:
- Turn the ignition switch off before measuring the resistances of the main wire and the branch wire.
- For Auto:
After the ignition switch is turned off, check that the key reminder warning system is not in operation.
- For Reminder:
After the ignition switch is turned off, check that the key reminder warning system and light reminder buzzer are not in operation.
- Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
- Turn the ignition switch off before measuring the resistances of the main wire and the branch wire.
- HINT:
- Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
Disconnect the cable from the negative (-) battery terminal before measuring the resistance of the main wire and the branch wire.
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
| NEXT | |
| 2. CHECK CAN BUS LINE FOR SHORT TO +B (DLC3 BRANCH WIRE) |
Disconnect the E75 No. 2 junction connector.

Measure the resistance of the DLC3.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E16-6 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E16-14 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | |
| 3. CONNECT CONNECTOR |
Reconnect the E75 No. 2 junction connector.
| NEXT | |
| 4. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 1 JUNCTION CONNECTOR SIDE) |
Disconnect the A51 No. 1 junction connector.

Measure the resistance of the DLC3.
Result Tester Connection
Switch Condition
Specified Condition
Proceed to
E16-6 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
B
E16-6 (CANH) - E16-16 (BAT)
Ignition switch off
Other
A
E16-14 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
B
E16-14 (CANL) - E16-16 (BAT)
Ignition switch off
Other
A
|
|
||||
| A | |
| 5. CONNECT CONNECTOR |
Reconnect the A51 No. 1 junction connector.
| NEXT | |
| 6. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 3 JUNCTION CONNECTOR, NO. 4 JUNCTION CONNECTOR SIDE) |
Disconnect the E77 No. 3 junction connector.

Measure the resistance of the DLC3.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E16-6 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E16-14 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | |
| 7. CONNECT CONNECTOR |
Reconnect the E77 No. 3 junction connector.
| NEXT | |
| 8. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 4 JUNCTION CONNECTOR SIDE) |
Disconnect the E76 No. 4 junction connector.

Measure the resistance of the DLC3.
Result Tester Connection
Switch Condition
Specified Condition
Proceed to
E16-6 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
B
E16-6 (CANH) - E16-16 (BAT)
Ignition switch off
Other
A
E16-14 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
B
E16-14 (CANL) - E16-16 (BAT)
Ignition switch off
Other
A
|
|
||||
| A | |
| 9. CONNECT CONNECTOR |
Reconnect the E76 No. 4 junction connector.
| NEXT | |
| 10. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 3 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY) |
Disconnect the E77 No. 3 junction connector.

Measure the resistance according to the value(s) in the table below.
Result Tester Connection
Switch Condition
Specified Condition
Proceed to
E77-1 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
B
E77-1 (CANH) - E16-16 (BAT)
Ignition switch off
Other
A
E77-12 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
B
E77-12 (CANL) - E16-16 (BAT)
Ignition switch off
Other
A
|
|
||||
| A | |
| 11. CONNECT CONNECTOR |
Reconnect the E77 No. 3 junction connector.
| NEXT | |
| 12. CHECK CAN BUS LINE FOR SHORT TO +B (CENTER AIRBAG SENSOR ASSEMBLY) |
Disconnect the E49 center airbag sensor connector.

Measure the resistance of the DLC3.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E16-6 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E16-14 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | ||
| ||
| 13. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 1 JUNCTION CONNECTOR - BRAKE ACTUATOR) |
- NOTICE:
- For vehicles without anti-lock brake system, go to "Check CAN Bus Line for Short to +B (No. 1 Junction Connector - ABS and Traction Actuator)".
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
A51-1 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
A51-12 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | |
| 14. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 1 JUNCTION CONNECTOR - ABS AND TRACTION ACTUATOR) |
- NOTICE:
- For vehicles without vehicle stability control system, go to "Check CAN Bus Line for Short to +B (No. 1 Junction Connector - ECM)".
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
A51-1 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
A51-12 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | |
| 15. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 1 JUNCTION CONNECTOR - ECM) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
A51-2 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
A51-13 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | ||
| ||
| 16. CONNECT CONNECTOR |
Reconnect the A51 No. 1 junction connector.
| NEXT | |
| 17. CHECK CAN BUS LINE FOR SHORT TO +B (BRAKE ACTUATOR) |
Disconnect the A27 brake actuator (skid control ECU) connector.

Measure the resistance of the DLC3.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E16-6 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E16-14 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | ||
| ||
| 18. CONNECT CONNECTOR |
Reconnect the A51 No. 1 junction connector.
| NEXT | |
| 19. CHECK CAN BUS LINE FOR SHORT TO +B (ABS AND TRACTION ACTUATOR) |
Disconnect the A67 ABS and traction actuator (skid control ECU) connector.

Measure the resistance of the DLC3.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E16-6 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E16-14 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | ||
| ||
| 20. CONNECT CONNECTOR |
Reconnect the A51 No. 1 junction connector.
| NEXT | |
| 21. CHECK CAN BUS LINE FOR SHORT TO +B (ECM) |
Disconnect the A12 ECM connector.

Measure the resistance of the DLC3.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E16-6 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E16-14 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | ||
| ||
| 22. CONNECT CONNECTOR |
Reconnect the E77 No. 3 junction connector.
| NEXT | |
| 23. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 2 JUNCTION CONNECTOR - YAW RATE SENSOR) |
- NOTICE:
- For vehicles without vehicle stability control system, go to "Check CAN Bus Line for Short to +B (No. 2 Junction Connector - Steering Angle Sensor)".
Disconnect the E75 No. 2 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E75-5 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E75-16 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | |
| 24. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 2 JUNCTION CONNECTOR - STEERING ANGLE SENSOR) |
- NOTICE:
- For vehicles without 2WD with vehicle stability control system and 4WD, go to "Check CAN Bus Line for Short to +B (No. 2 Junction Connector - Power Steering ECU)".
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E75-7 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E75-18 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | |
| 25. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 2 JUNCTION CONNECTOR - POWER STEERING ECU) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E75-6 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E75-17 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | |
| 26. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 2 JUNCTION CONNECTOR - MAIN BODY ECU) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E75-8 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E75-19 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | |
| 27. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E75-4 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E75-15 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | ||
| ||
| 28. CONNECT CONNECTOR |
Reconnect the E75 No. 2 junction connector.
| NEXT | |
| 29. CHECK CAN BUS LINE FOR SHORT TO +B (YAW RATE SENSOR) |
Disconnect the K25 yaw rate sensor connector.

Measure the resistance of the DLC3.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E16-6 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E16-14 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | ||
| ||
| 30. CONNECT CONNECTOR |
Reconnect the E75 No. 2 junction connector.
| NEXT | |
| 31. CHECK CAN BUS LINE FOR SHORT TO +B (STEERING ANGLE SENSOR) |
Disconnect the E95 steering angle sensor connector.

Measure the resistance of the DLC3.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E16-6 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E16-14 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | ||
| ||
| 32. CONNECT CONNECTOR |
Reconnect the E75 No. 2 junction connector.
| NEXT | |
| 33. CHECK CAN BUS LINE FOR SHORT TO +B (POWER STEERING ECU) |
Disconnect the E21 power steering ECU connector.

Measure the resistance of the DLC3.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E16-6 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E16-14 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | ||
| ||
| 34. CONNECT CONNECTOR |
Reconnect the E75 No. 2 junction connector.
| NEXT | |
| 35. CHECK CAN BUS LINE FOR SHORT TO +B (MAIN BODY ECU) |
Disconnect the E20 main body ECU connector.

Measure the resistance of the DLC3.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E16-6 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E16-14 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | ||
| ||
| 36. CONNECT CONNECTOR |
Reconnect the E75 No. 2 junction connector.
| NEXT | |
| 37. CHECK CAN BUS LINE FOR SHORT TO +B (AIR CONDITIONING AMPLIFIER) |
Disconnect the E41*1 or E42*2 air conditioning amplifier connector.

- HINT:
- *1: for Automatic Air Conditioning System.
- *2: for Manual Air Conditioning System.
- *1: for Automatic Air Conditioning System.
Measure the resistance of the DLC3.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E16-6 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E16-14 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | ||
| ||
| 38. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 4 JUNCTION CONNECTOR - 4WD CONTROL ECU) |
- NOTICE:
- For vehicles without 4WD, go to "Check CAN Bus Line for Short to +B (No. 4 Junction Connector - Combination Meter ECU)".
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E76-7 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E76-18 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | |
| 39. CHECK CAN BUS LINE FOR SHORT TO +B (NO. 4 JUNCTION CONNECTOR - COMBINATION METER ECU) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E76-5 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E76-16 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | |
| 40. CONNECT CONNECTOR |
Reconnect the E76 No. 4 junction connector.
| NEXT | |
| 41. CHECK CAN BUS LINE FOR SHORT TO +B (4WD CONTROL ECU) |
Disconnect the E67 4WD control ECU connector.

Measure the resistance of the DLC3.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E16-6 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E16-14 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | ||
| ||
| 42. CONNECT CONNECTOR |
Reconnect the E76 No. 4 junction connector.
| NEXT | |
| 43. CHECK CAN BUS LINE FOR SHORT TO +B (COMBINATION METER ECU) |
Disconnect the E22 combination meter ECU connector.

Measure the resistance of the DLC3.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E16-6 (CANH) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
E16-14 (CANL) - E16-16 (BAT)
Ignition switch off
1 MΩ or more
|
|
||||
| OK | ||
| ||
