2005-2008 RAV4 · Service Manual BRAKE

C1267/67 Brake Pedal Load Sensing Switch

Diagnostic trouble codes · Vehicles built Jan 2007 – Jul 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 Aug 2007 – Jul 2008

DESCRIPTION

The brake pedal load sensing switch is turned on when the brake pedal is depressed with force exceeding a predetermined level.
The skid control ECU detects if the brake pedal is depressed or not via this circuit.
DTC No.
DTC Detection Condition
Trouble Area
C1267/67
When one of following conditions is met:
  1. An open or short in the brake pedal load sensing switch continues for 0.3 seconds or more.
  2. Immediately after the ignition switch is turned on (IG), the brake pedal load sensing switch is ON and the stop light switch is OFF for 10 seconds or more.
  3. While the vehicle speed change from 0 mph (0 km/h) to 18 mph (30 km/h), the condition that the brake pedal load sensing switch remains ON occurs 5 times in succession.
  4. With the stop light switch ON, the brake pedal load sensing switch OFF, and the master cylinder pressure 6 Mpa or more, the deceleration is 0.4 G or more for 1 second or more.
  5. With the stop light switch ON, the brake pedal load sensing switch OFF, and the master cylinder pressure 6 Mpa or more, the vehicle speed is 0 mph (0 km/h) for 5 seconds or more.
  1. Brake pedal load sensing switch
  2. Brake pedal load sensing switch circuit

WIRING DIAGRAM

C126312E01

INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform zero point calibration (Click here).

HINT:
If C1249/49 is output, repair it before repairing C1267/67 based on the flow chart below.


1. READ VALUE USING INTELLIGENT TESTER (BRAKE PEDAL LOAD SENSING SWITCH)
  1. Check the Data List for proper functioning of the brake pedal load sensing switch.

    Skid control ECU 
    Item (Display)
    Measurement Item / Range (Display)
    Normal Condition
    Diagnostic Note
    Brake Pedal Load Sensing SW
    Brake pedal load sensing switch / ON or OFF
    ON: Depressed brake pedal
    OFF: Released brake pedal
    -

    OK:
    ON (brake pedal is depressed) appears on the screen.



OK
Go to step 4
NG


2. INSPECT BRAKE PEDAL LOAD SENSING SWITCH
C129075E01
C129074E01

NOTICE:
  1. Do not remove the brake pedal load sensing switch from the brake pedal.
  2. When there is a malfunction in the brake pedal load sensing switch, replace the brake pedal.

  1. Turn the ignition switch off.

  1. Disconnect the brake pedal load sensing switch connector.

  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    2 - 1
    Brake pedal depressed (OFF)
    0.95 to 1.05 kΩ
    2 - 1
    Brake pedal released (ON)
    202.4 to 223.7 Ω



NG
REPLACE BRAKE PEDAL SUPPORT ASSEMBLY
OK


3. CHECK WIRE HARNESS (SKID CONTROL ECU - BRAKE PEDAL LOAD SENSING SWITCH)

  1. C110685E05
    Disconnect the A26 ECU connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    A26-7 (FSW+) - A3-2
    Below 1 Ω
    A26-7 (FSW+) - Body ground
    10 kΩ or higher
    A3-1 - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


4. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Check if the same DTC is recorded (Click here).

    Result 
    Result
    Proceed to
    DTC (C1267/67) is not output
    A
    DTC (C1267/67) is output
    B



B
REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY
A

USE SIMULATION METHOD TO CHECK


← C1267/67 Brake Pedal Load Sensing Switch (Nov 2005 – Dec 2006)C1267/67 Brake Pedal Load Sensing Switch (Aug 2007 – Jul 2008) →