2005-2008 RAV4 · Service Manual BRAKE

C1380/64 Stop Light Control Relay Malfunction

Diagnostic trouble codes · Vehicles built Jan 2007 – Jul 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 Aug 2007 – Jul 2008

DESCRIPTION

The skid control ECU inputs the stop light switch signal and detects the status of the brake operation.
DTC No.
DTC Detection Condition
Trouble Area
C1380/64
When one of following conditions is met:
  1. When stop light control relay is ON, relay OFF condition continues for 5 seconds or more
  2. When stop light control relay is OFF, relay ON condition continues for 5 seconds or more
  3. With the stop light control relay is OFF, and the stop light switch ON, stop switch monitor (STP2) OFF condition continues for 5 seconds or more
  1. Stop light assembly
  2. Stop light switch circuit
  3. Stop light control relay
  4. ABS and TRACTION actuator (skid control ECU)

WIRING DIAGRAM

C126302E01
C126303E01

INSPECTION PROCEDURE

NOTICE:
When replacing the ABS and TRACTION actuator, perform zero point calibration (Click here).


1. CHECK STOP LIGHT (OPERATION)
  1. Check that the light illuminates when the brake pedal is depressed, and turns off when the brake pedal is released.

    OK 
    Condition
    Stop Light Condition
    Brake pedal depressed
    Illuminates
    Brake pedal released
    Turn off



NG
Go to step 9
OK


2. CHECK WIRE HARNESS (SKID CONTROL ECU - BATTERY)

  1. C121700E28
    Disconnect the A26 ECU connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A26-21 (STP2) - Body ground
    Brake pedal depressed
    8 to 16 V
    A26-21 (STP2) - Body ground
    Brake pedal released
    Below 1.5 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


3. CHECK WIRE HARNESS (SKID CONTROL ECU)

  1. C121700E29
    Disconnect the A26 ECU connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    A26-21 (STP2) - A26-27 (STP1)
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


4. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (STOP LIGHT RELAY)
  1. Select the Active Test, generate a control command, and then check that the stop light relay operates.

    Skid control ECU 
    Item
    Test Details
    Diagnosis Note
    Stop Lamp Relay
    Turn stop light relay ON / OFF
    Observe stop light

    OK:
    The stop lights illuminate or turn off.



NG
Go to step 6
OK


5. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 5 km/h (3 mph) or more for several seconds.

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY

6. INSPECT STOP LIGHT CONTROL RELAY (Marking: BRK)

  1. A087121E01
    Remove the stop light control relay from the engine room No. 1 relay block.

  1. Measure the resistance of the relay.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 4
    Below 1 Ω
    3 - 5
    10 kΩ or higher
    3 - 4
    10 kΩ or higher
    (when battery voltage is applied to terminals 1 and 2)
    3 - 5
    Below 1 Ω
    (when battery voltage is applied to terminals 1 and 2)



NG
REPLACE STOP LIGHT CONTROL RELAY
OK


7. CHECK WIRE HARNESS (ENGINE ROOM NO. 1 RELAY BLOCK - SKID CONTROL ECU AND BATTERY)

  1. C126306E01
    Remove the stop light control relay.

  1. Disconnect the A26 ECU connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    BRK relay terminal 5 - Body ground
    Always
    8 to 16 V
    BRK relay terminal 2 - Body ground
    Ignition switch on (IG)
    8 to 16 V

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    BRK relay terminal 1 - A26-16 (STPO)
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


8. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 5 km/h (3 mph) or more for several seconds.

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY

9. CHECK WIRE HARNESS (STOP LIGHT SWITCH - BATTERY)

  1. C082562E02
    Disconnect the A5 switch connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    A5-2 - Body ground
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


10. INSPECT STOP LIGHT SWITCH ASSEMBLY

  1. C108891E01
    Remove the stop light switch connector.

  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Switch pin not pushed
    Below 1 Ω
    1 - 2
    Switch pin pushed
    10 kΩ or higher
    3 - 4
    Switch pin not pushed
    10 kΩ or higher
    3 - 4
    Switch pin pushed
    Below 1 Ω



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY
OK


11. CHECK WIRE HARNESS (STOP LIGHT SWITCH - STOP LIGHT CONTROL RELAY)

  1. C126330E01
    Disconnect the A5 switch connector.

  1. Remove the stop light control relay.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    A5-1 - BKR relay Terminal 4
    Below 1 Ω
    A5-1 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


12. INSPECT STOP LIGHT CONTROL RELAY (Marking: BRK)

  1. A087121E01
    Remove the stop light control relay from the engine room No. 1 relay block.

  1. Measure the resistance of the relay.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 4
    Below 1 Ω
    3 - 5
    10 kΩ or higher
    3 - 4
    10 kΩ or higher
    (when battery voltage is applied to terminals 1 and 2)
    3 - 5
    Below 1 Ω
    (when battery voltage is applied to terminals 1 and 2)



NG
REPLACE STOP LIGHT CONTROL RELAY
OK


13. CHECK WIRE HARNESS (STOP LIGHT AND REAR COMBINATION LIGHT - CONTROL RELAY)

  1. C126331E01
    Disconnect the S1, K13 and K15 light connectors.

  1. Remove the stop light control relay.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    K13-4 - BKR relay terminal 3
    Below 1 Ω
    K13-4 - Body ground
    10 kΩ or higher
    K13-1 - Body ground
    Below 1 Ω
    K15-4 - BKR relay terminal 3
    Below 1 Ω
    K15-4 - Body ground
    10 kΩ or higher
    K15-1 - Body ground
    Below 1 Ω
    S1-2 - BKR relay terminal 3
    Below 1 Ω
    S1-2 - Body ground
    10 kΩ or higher
    S1-1 - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

USE SIMULATION METHOD TO CHECK (Click here)


← C1380/64 Stop Light Control Relay Malfunction (Nov 2005 – Dec 2006)C1380/64 Stop Light Control Relay Malfunction (Aug 2007 – Jul 2008) →