REASSEMBLY
Removal / installation · Vehicles built from Aug 2008
Versions by build date: Nov 2005 – Jul 2007 Aug 2007 – Jul 2008 from Aug 2008
- HINT:
- A bolt without a torque specification is shown in the standard bolt chart (Click here).
| 1. INSTALL FRONT BUMPER EXTENSION LH (for Wide Body) |
![]() ![]() |
Attach the 6 clips to install the extension.
Install the screw.
| 2. INSTALL FRONT BUMPER EXTENSION RH (for Wide Body) |
- HINT:
- Use the procedure described for the LH side.
| 3. INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light) |
![]() ![]() |
Attach the 2 guides to install the fog light.
Install the screw.
| 4. INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light) |
- HINT:
- Use the procedure described for the LH side.
| 5. INSTALL FRONT BUMPER HOLE COVER LH |
Attach the 4 claws to install the bumper hole cover.


| 6. INSTALL FRONT BUMPER HOLE COVER RH |
- HINT:
- Use the procedure described for the LH side.
| 7. INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET |
![]() ![]() |
Attach the 2 claws to install the mounting bracket.
Install the 2 screws.
| 8. INSTALL FRONT BUMPER BAR |
Clean the bumper cover surface.
Using a heat light, heat the bumper cover surface.
- Standard:
Item
Specified Condition
Bumper cover
20 to 30°C (68 to 86°F)
- NOTICE:
- Do not heat the bumper cover excessively.
Remove the double-sided tape from the bumper cover.
Wipe off any tape adhesive residue with cleaner.
If reusing the bumper bar, clean the bumper bar.
Remove the double-sided tape from the bumper bar.
Wipe off any tape adhesive residue with cleaner.
Apply new double-sided tape to the bumper bar.
Install the bumper bar.

Using a heat light, heat the bumper cover and bumper bar.
- Standard:
Item
Specified Condition
Bumper cover
20 to 30°C (68 to 86°F)
Bumper bar
20 to 30°C (68 to 86°F)
- NOTICE:
- Do not heat the bumper cover and bumper bar excessively.
Remove the peeling paper from the face of the bumper bar.
- HINT:
- After removing the peeling paper, keep the exposed adhesive free from foreign matter.
Install the bumper bar.
- HINT:
- Press the bumper bar firmly to install it.
| 9. INSTALL FRONT BUMPER ARM EXTENSION LH |
![]() ![]() |
Attach the claw to install the arm extension.
Install the screw and clip.
| 10. INSTALL FRONT BUMPER ARM EXTENSION RH |
- HINT:
- Use the procedure described for the LH side.
| 11. INSTALL LOWER NO. 2 RADIATOR GRILLE |
![]() ![]() |
Attach the 12 claws and 3 guides to install the lower No. 2 radiator grille.
| 12. INSTALL LOWER NO. 1 RADIATOR GRILLE |
![]() ![]() |
Attach the 16 claws to install the lower No. 1 radiator grille.
| 13. INSTALL RADIATOR GRILLE SUB-ASSEMBLY |
![]() ![]() |
Attach the 7 claws and guide to install the radiator grille.
Install the 3 bolts and 3 nuts.

| 14. INSTALL HOOD TO RADIATOR GRILLE SEAL |
Clean the bumper cover surface.
Using a heat light, heat the bumper cover surface.
- Standard:
Item
Specified Condition
Bumper cover
20 to 30°C (68 to 86°F)
- NOTICE:
- Do not heat the bumper cover excessively.
Remove the double-sided tape from the bumper cover.
Wipe off any tape adhesive residue with cleaner.
Install a new hood to radiator grille seal.

Using a heat light, heat the bumper cover and hood to radiator grille seal.
- Standard:
Item
Specified Condition
Bumper cover
20 to 30°C (68 to 86°F)
Hood to radiator grille seal
20 to 30°C (68 to 86°F)
- NOTICE:
- Do not heat the bumper cover and hood to radiator grille seal excessively.
Attach the 9 clips to install the hood to radiator grille seal.
Install the 4 clips.
Remove the peeling paper from the face of the hood to radiator grille seal.
Attach the double-sided tape on the hood to radiator grille seal to the bumper cover.
- HINT:
- Press the hood to radiator grille seal firmly to install it.







