DISASSEMBLY
Removal / installation · Vehicles built from Nov 2005
| 1. INSPECT OIL PUMP ASSEMBLY |
![]() ![]() |
Turn the drive gear with 2 screwdrivers and make sure it rotates smoothly.
- NOTICE:
- Be careful not to damage the oil seal lip.
| 2. REMOVE CLUTCH DRUM OIL SEAL RING |
![]() ![]() |
Remove the 2 clutch drum oil seal rings.
| 3. REMOVE STATOR SHAFT ASSEMBLY |
![]() ![]() |
Using a T30 ''torx'' socket, remove the 11 bolts and stator shaft. Keep the gears in assembling order.
| 4. INSPECT CLEARANCE OF OIL PUMP ASSEMBLY |
![]() ![]() |
Push the driven gear to one side of the body. Using a feeler gauge, measure the clearance.
- Standard body clearance:
- 0.10 to 0.17 mm (0.0039 to 0.0067 in.)
- Maximum body clearance:
- 0.17 mm (0.0067 in.)
Measure the tip clearance between the driven gear teeth and drive gear teeth.

- Standard tip clearance:
- 0.07 to 0.15 mm (0.0028 to 0.0059 in.)
- Maximum tip clearance:
- 0.15 mm (0.0059 in.)
Using a straightedge and feeler gauge, measure the side clearance of both gears.

- Standard side clearance:
- 0.02 to 0.05 mm (0.0008 to 0.0020 in.)
- Maximum side clearance:
- 0.05 mm (0.0020 in.)
- Standard drive gear thickness:
Mark
Thickness
1
10.690 to 10.699 mm (0.4209 to 0.4212 in.)
2
10.700 to 10.709 mm (0.4213 to 0.4216 in.)
3
10.710 to 10.720 mm (0.4217 to 0.4220 in.)
4
10.721 to 10.730 mm (0.4221 to 0.4224 in.)
5
10.731 to 10.740 mm (0.4225 to 0.4228 in.)
- Standard driven gear thickness:
Mark
Thickness
1
10.690 to 10.699 mm (0.4209 to 0.4212 in.)
2
10.700 to 10.709 mm (0.4213 to 0.4216 in.)
3
10.710 to 10.720 mm (0.4217 to 0.4220 in.)
4
10.721 to 10.730 mm (0.4221 to 0.4224 in.)
5
10.731 to 10.740 mm (0.4225 to 0.4228 in.)
| 5. REMOVE FRONT OIL PUMP DRIVE GEAR |
![]() ![]() |
Remove the front oil pump drive gear.
| 6. REMOVE FRONT OIL PUMP DRIVEN GEAR |
![]() ![]() |
Remove the front oil pump driven gear.
| 7. REMOVE FRONT OIL PUMP BODY O-RING |
![]() ![]() |
Using a screwdriver, pry out the O-ring.
- HINT:
- Tape the screwdriver before use.
| 8. REMOVE FRONT OIL PUMP OIL SEAL |
![]() ![]() |
Mount the oil pump in a soft jaw vise.
Using SST, tap out the oil seal from the oil pump body.
- SST
- 09308-00010
| 9. INSPECT FRONT OIL PUMP AND GEAR BODY SUB-ASSEMBLY |
![]() ![]() |
Using a caliper gauge, measure the inside diameter of the oil pump body bush.
- Standard inside diameter:
- 38.113 to 38.138 mm (1.50051 to 1.50149 in.)
- Maximum inside diameter:
- 38.188 mm (1.50346 in.)
| 10. INSPECT STATOR SHAFT ASSEMBLY |
![]() ![]() |
Using a caliper gauge, measure the inside diameter of the stator shaft bush.
- Standard inside diameter:
- 21.500 to 21.526 mm (0.84646 to 0.84748 in.)
- Maximum inside diameter:
- 21.57 mm (0.8492 in.)










