2005-2008 RAV4 · Service Manual TRANSMISSION

INSPECTION

Inspection · Vehicles built from Nov 2005


INSPECT OIL PUMP ASSEMBLY

D009205E01
  1. Turn the drive gear with 2 screwdrivers and make sure it rotates smoothly.

    NOTICE:
    Be careful not to damage the oil seal lip.


INSPECT CLEARANCE OF OIL PUMP ASSEMBLY

D009207E02
  1. Push the driven gear to one side of the body. Using a feeler gauge, measure the clearance.

    Standard body clearance:
    0.10 to 0.17 mm (0.0039 to 0.0067 in.)

    Maximum body clearance:
    0.17 mm (0.0067 in.)

    If the body clearance is greater than the maximum, replace the oil pump body sub-assembly.

  1. D009208E01
    Measure the tip clearance between the driven gear teeth and drive gear teeth.

    Standard tip clearance:
    0.07 to 0.15 mm (0.0028 to 0.0059 in.)

    Maximum tip clearance:
    0.15 mm (0.0059 in.)

    If the tip clearance is grater than the maximum, replace the oil pump body sub-assembly.

  1. D009209E01
    Using a straightedge and feeler gauge, measure the side clearance of both gears.

    Standard side clearance:
    0.02 to 0.05 mm (0.0008 to 0.0020 in.)

    Maximum side clearance:
    0.05 mm (0.0020 in.)

    Standard drive gear thickness:
    Mark
    Thickness
    1
    10.690 to 10.699 mm (0.4209 to 0.4212 in.)
    2
    10.700 to 10.709 mm (0.4213 to 0.4216 in.)
    3
    10.710 to 10.720 mm (0.4217 to 0.4220 in.)
    4
    10.721 to 10.730 mm (0.4221 to 0.4224 in.)
    5
    10.731 to 10.740 mm (0.4225 to 0.4228 in.)

    Standard driven gear thickness:
    Mark
    Thickness
    1
    10.690 to 10.699 mm (0.4209 to 0.4212 in.)
    2
    10.700 to 10.709 mm (0.4213 to 0.4216 in.)
    3
    10.710 to 10.720 mm (0.4217 to 0.4220 in.)
    4
    10.721 to 10.730 mm (0.4221 to 0.4224 in.)
    5
    10.731 to 10.740 mm (0.4225 to 0.4228 in.)


INSPECT FRONT OIL PUMP AND GEAR BODY SUB-ASSEMBLY

D003648E01
  1. Using a caliper gauge, measure the inside diameter of the oil pump body bush.

    Standard inside diameter:
    38.113 to 38.138 mm (1.50051 to 1.50149 in.)

    Maximum inside diameter:
    38.188 mm (1.50346 in.)

    If the inside diameter is grater than maximum, replace the oil pump body sub-assembly.


INSPECT STATOR SHAFT ASSEMBLY

D003653E01
  1. Using a caliper gauge, measure the inside diameter of the stator shaft bush.

    Standard inside diameter:
    21.500 to 21.526 mm (0.84646 to 0.84748 in.)

    Maximum inside diameter:
    21.57 mm (0.8492 in.)

    If the indicator diameter is greater than the maximum, replace the stator shaft.

← DISASSEMBLY (from Nov 2005)REASSEMBLY (from Nov 2005) →