2005-2008 RAV4 · Service Manual STEERING

DATA LIST / ACTIVE TEST

System information · Vehicles built Nov 2005 – Jul 2008

Versions by build date: Nov 2005 – Jul 2008 from Aug 2008


READ DATA LIST

HINT:
Using the intelligent tester's Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch on (IG) and press the intelligent tester main switch ON.

  3. Read the Data List by following the directions on the tester screen.

    Power steering ECU 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Reference Value
    Battery Voltage
    Battery voltage:
    Min.: 0 V
    Max.: 25.5 V
    -
    10 to 14 V
    Meter Vehicle Velocity
    Vehicle speed from meter:
    Min.: 0 km/h (0 mph)
    Max.: 300 km/h (187.5 mph)
    Vehicle stopped
    0 km/h (0 mph)
    Vehicle driven at constant speed
    No significant fluctuation
    Spd Sig Invalid Record
    Record of vehicle speed signal invalid:
    REC or UNREC
    -
    UNREC
    Engine Revolution
    Show the engine revolution:
    Min.: 0 rpm
    Max.: 12800 rpm
    Engine is running at a constant speed
    No significant fluctuation
    Eng Rev Inter Record
    Record of engine revolution signal interruption:
    REC or UNREC
    -
    UNREC
    Motor Actual Current
    Amount of current to motor:
    Min.: -327.68 A
    Max.: 327.67 A
    Power steering is in operation
    Value changes in proportion to steering effort
    Command Value Current
    Demanded amount of current to motor:
    Min.: -327.68 A
    Max.: 327.68 A
    Power steering is in operation
    Value changes in proportion to steering effort
    Steering Angle Velocity
    Steering angle speed:
    Min.: -32768°/sec.
    Max.: 32767°/sec.
    Steering wheel is turned
    Value changes in proportion to steering effort
    Steering Wheel Torque
    Steering wheel torque:
    Min.: -7 Nm
    Max.: 7 Nm
    -
    -
    Thermistor Temperature
    ECU substrate temperature:
    Min.: -40°C
    Max.: 150°C
    Ignition switch on (IG)
    -
    PIG Power Supply
    Power source voltage to activate motor:
    Min.: 0 V
    Max.: 20.1531 V
    Power steering in operation
    10 to 14 V
    IG Power Supply
    ECU power source voltage:
    Min.: 0 V
    Max.: 20.1531 V
    Ignition switch on (IG)
    10 to 14 V
    Motor Overheat Record
    Continuous overheat prevention control record:
    REC or UNREC
    -
    UNREC
    Motor Lo Power Record
    PIG power source voltage drop record:
    REC or UNREC
    -
    UNREC
    Motor Rotation Angle
    Motor rotation angle:
    Min.: 0°
    Max.: 360°
    Power steering in operation
    During steering operation, motor rotation angle value changes from 0 to 360°
    Motor Voltage
    Motor power supply voltage:
    0 V
    Max.: 45.955 V
    Power steering in operation
    -
    Motor Terminal Volt (U)
    Motor terminal voltage (U phase):
    Min.: 0 V
    Max.: 46.667 V
    Engine running and steering wheel turned
    When the steering wheel is turned, a voltage between 1 V and approximately 1 V less than the battery voltage is displayed.
    Motor Terminal Volt (V)
    Motor terminal voltage (V phase):
    Min.: 0 V
    Max.: 46.667 V
    Engine running and steering wheel turned
    When the steering wheel is turned, a voltage between 1 V and approximately 1 V less than the battery voltage is displayed.
    Motor Terminal Volt (W)
    Motor Terminal voltage (W phase):
    Min.: 0 V
    Max.: 46.667 V
    Engine running and steering wheel turned
    When the steering wheel is turned, a voltage between 1 V and approximately 1 V less than the battery voltage is displayed.
    IG ON/OFF Times
    Ignition switch ON/OFF number of times after fail detection:
    Min.: 0 times
    Max.: 65535 times
    -
    -
    The Number of DTCs
    Number of detected DTCs when freeze frame data stored:
    Min.: 0
    Max.: 255
    -
    -
    PS Assist Signal
    Power steering assist signal:
    ON or OFF
    -
    -


PERFORM ACTIVE TEST

HINT:
Performing the intelligent tester's Active Test allows relays, the VSV, actuators and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time. The Data List can be displayed in the Active Test.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch on (IG) and turn the intelligent tester ON.

  3. Perform the Active Test by following the prompts on the tester.

    Combination meter 
    Tester Display
    Test Part
    Control Range
    Indicat. EPS
    P/S indicator
    ON/OFF
    Confirm that vehicle is stopped, engine idling

← FAIL-SAFE CHART (from Aug 2008)DATA LIST / ACTIVE TEST (from Aug 2008) →