DATA LIST / ACTIVE TEST
System information · Vehicles built from Aug 2008
Versions by build date: Nov 2005 – Jul 2008 from Aug 2008
| READ DATA LIST |
- HINT:
- Using the intelligent tester's Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and press the intelligent tester main switch ON.
Read the Data List by following the directions on the tester screen.
Power steering ECU Tester Display
Measurement Item/Range
Normal Condition
Reference Value
Battery Voltage
Battery voltage:
Min.: 0 V
Max.: 25.5 V
-
10 to 14 V
Meter Vehicle Velocity
Vehicle speed from meter:
Min.: 0 km/h (0 mph)
Max.: 300 km/h (187.5 mph)
Vehicle stopped
0 km/h (0 mph)
Vehicle driven at constant speed
No significant fluctuation
Spd Sig Invalid Record
Record of vehicle speed signal invalid:
REC or UNREC
-
UNREC
Engine Revolution
Show the engine revolution:
Min.: 0 rpm
Max.: 12800 rpm
Engine is running at a constant speed
No significant fluctuation
Eng Rev Inter Record
Record of engine revolution signal interruption:
REC or UNREC
-
UNREC
Motor Actual Current
Amount of current to motor:
Min.: -327.68 A
Max.: 327.67 A
Power steering is in operation
Value changes in proportion to steering effort
Command Value Current
Demanded amount of current to motor:
Min.: -327.68 A
Max.: 327.68 A
Power steering is in operation
Value changes in proportion to steering effort
Steering Angle Velocity
Steering angle speed:
Min.: -32768°/sec.
Max.: 32767°/sec.
Steering wheel is turned
Value changes in proportion to steering effort
Steering Wheel Torque
Steering wheel torque:
Min.: -7 Nm
Max.: 7 Nm
-
-
Thermistor Temperature
ECU substrate temperature:
Min.: -40°C
Max.: 150°C
Ignition switch on (IG)
-
PIG Power Supply
Power source voltage to activate motor:
Min.: 0 V
Max.: 20.1531 V
Power steering in operation
10 to 14 V
IG Power Supply
ECU power source voltage:
Min.: 0 V
Max.: 20.1531 V
Ignition switch on (IG)
10 to 14 V
Motor Overheat Record
Continuous overheat prevention control record:
REC or UNREC
-
UNREC
Motor Lo Power Record
PIG power source voltage drop record:
REC or UNREC
-
UNREC
Battery Voltage Lo Record
Number of battery voltage low:
Min.: 0 times
Max.: 65535 times
-
-
Motor Rotation Angle
Motor rotation angle:
Min.: 0°
Max.: 360°
Power steering in operation
During steering operation, motor rotation angle value changes from 0 to 360°
Motor Voltage
Motor power supply voltage:
0 V
Max.: 45.955 V
Power steering in operation
-
Motor Terminal Volt (U)
Motor terminal voltage (U phase):
Min.: 0 V
Max.: 46.667 V
Engine running and steering wheel turned
When the steering wheel is turned, a voltage between 1 V and approximately 1 V less than the battery voltage is displayed.
Motor Terminal Volt (V)
Motor terminal voltage (V phase):
Min.: 0 V
Max.: 46.667 V
Engine running and steering wheel turned
When the steering wheel is turned, a voltage between 1 V and approximately 1 V less than the battery voltage is displayed.
Motor Terminal Volt (W)
Motor Terminal voltage (W phase):
Min.: 0 V
Max.: 46.667 V
Engine running and steering wheel turned
When the steering wheel is turned, a voltage between 1 V and approximately 1 V less than the battery voltage is displayed.
IG ON/OFF Times
Ignition switch ON/OFF number of times after fail detection:
Min.: 0 times
Max.: 65535 times
-
-
The Number of DTCs
Number of detected DTCs when freeze frame data stored:
Min.: 0
Max.: 255
-
-
PS Assist Signal
Power steering assist signal:
ON or OFF
-
-
| PERFORM ACTIVE TEST |
- HINT:
- Performing the intelligent tester's Active Test allows relays, the VSV, actuators and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time. The Data List can be displayed in the Active Test.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the intelligent tester ON.
Perform the Active Test by following the prompts on the tester.
Combination meter Tester Display
Test Part
Control Range
Indicat. EPS
P/S indicator
ON/OFF
Confirm that vehicle is stopped, engine idling