2005-2008 RAV4 · Service Manual SECURITIES

TERMINALS OF ECU

System information · Vehicles built Jan 2007 – Jul 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007


CHECK TRANSPONDER KEY AMPLIFIER
B065593E19
  1. Disconnect the E8 amplifier connector.

  2. Measure the resistance of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    AGND (E8-7) - Body ground
    R - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the E8 amplifier connector.

  4. Measure the resistance and voltage of the connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    AGND (E8-7) - Body ground
    R - Body ground
    Ground
    Always
    Below 1 Ω
    VC5 (E8-1) - AGND (E8-7)
    B - R
    Power source
    No key is in ignition key cylinder
    Below 1 V
    Key inserted
    4.6 to 5.4 V
    CODE (E8-4) - AGND (E8-7)
    P - R
    Demodulated signal of key code data
    No key is in ignition key cylinder
    Below 1 V
    Key inserted
    Pulse generation (see waveform 1)
    TXCT (E8-5) - AGND (E8-7)
    G - R
    Key code output signal
    No key is in ignition key cylinder
    Below 1 V
    Key inserted
    Pulse generation (see waveform 2)
    If the result is not as specified, there may be a malfunction in the amplifier.

  5. B069240E13
    Using an oscilloscope, check the waveform 1.
    Waveform 1 (Reference): 
    Item
    Content
    Symbols (Terminal No.)
    CODE (E8-4) - AGND (E8-7)
    Tool Setting
    5 V/DIV., 20 msec./DIV.
    Condition
    Key inserted

  6. B069239E10
    Using an oscilloscope, check the waveform 2.
    Waveform 2 (Reference): 
    Item
    Content
    Symbols (Terminal No.)
    TXCT (E8-5) - AGND (E8-7)
    Tool Setting
    5 V/DIV., 20 msec./DIV.
    Condition
    Key inserted


CHECK TRANSPONDER KEY ECU
B121962E05
  1. Disconnect the E50 ECU connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    GND (E50-16) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    +B (E50-1) - GND (E50-16)
    R - W-B
    Battery
    Always
    10 to 14 V
    IG (E50-2) - GND (E50-16)
    B - W-B
    Ignition switch
    Ignition switch off
    Below 1 V
    Ignition switch on (IG)
    10 to 14 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the E50 ECU connector.

  4. Measure the resistance and voltage of the connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    AGND (E50-5) - GND (E50-16)
    R - W-B
    Amplifier ground circuit
    Always
    Below 1 Ω
    EGND (E50-11) - GND (E50-16)
    V - W-B
    ECM ground circuit
    Always
    Below 1 Ω
    KSW (E50-3) - GND (E50-16)
    L - W-B
    Unlock warning switch
    No key is in ignition key cylinder
    10 to 14 V
    Key inserted
    Below 1 V
    VC5 (E50-14) - AGND (E50-5)
    B - R
    Power source
    No key is in ignition key cylinder
    Below 1 V
    Key inserted
    4.6 to 5.4 V
    TXCT (E50-4) - AGND (E50-5)
    G - R
    Transponder key amplifier communication signal
    No key is in ignition key cylinder
    Below 1 V
    Key inserted
    Pulse generation (see waveform 1)
    CODE (E50-15) - AGND (E50-5)
    P - R
    Transponder key amplifier communication signal
    No key is in ignition key cylinder
    Below 1 V
    Key inserted
    Pulse generation (see waveform 2)
    EFIO (E50-13) - EGND (E50-11)
    P - V
    ECM output signal
    Ignition switch off
    Below 1 V
    Ignition switch on (IG)
    Pulse generation (see waveform 3)
    EFII (E50-12) - EGND (E50-11)
    LG - V
    ECM input signal
    Ignition switch off
    Below 1 V
    Ignition switch off
    Pulse generation (see waveform 4)
    IND (E50-8)- GND (E50-16)
    Y - W-B
    Security indicator light signal
    Engine immobiliser system SET
    3 to 5 V
    Engine immobiliser system UNSET
    Below 1 V
    D (E50-9) - GND (E50-16)
    W - W-B
    Diagnosis tester communication
    Ignition switch on
    Pulse generation
    If the result is not as specified, there may be a malfunction in the ECU.

  5. B069239E11
    Using an oscilloscope, check the waveform 1.
    Waveform 1 (Reference): 
    Item
    Content
    Symbols (Terminal No.)
    TXCT (E50-4) - AGND (E50-5)
    Tool Setting
    5 V/DIV., 20 msec./DIV.
    Condition
    Key inserted

  6. B069240E14
    Using an oscilloscope, check the waveform 2.
    Waveform 2 (Reference): 
    Item
    Content
    Symbols (Terminal No.)
    CODE (E50-15) - AGND (E50-5)
    Tool Setting
    5 V/DIV., 20 msec./DIV.
    Condition
    Key inserted

  7. B069241E07
    Using an oscilloscope, check the waveform 3.
    Waveform 3 (Reference): 
    Item
    Content
    Symbols (Terminal No.)
    EFIO (E50-13) - EGND (E50-11)
    Tool Setting
    10 V/DIV., 500 msec./DIV.
    Condition
    Ignition switch on (IG)

  8. B069242E09
    Using an oscilloscope, check the waveform 4.
    Waveform 4 (Reference): 
    Item
    Content
    Symbols (Terminal No.)
    EFII (E50-12) - EGND (E50-11)
    Tool Setting
    10 V/DIV., 500 msec./DIV.
    Condition
    Ignition switch on (IG)


CHECK ECM (for 1AZ-FE, 2AZ-FE)
B116297E03
  1. Measure the resistance and voltage of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    EOM (A12-9) - Body ground
    V - Body ground
    Ground
    Always
    Below 1 Ω
    IMI (A12-11) - EOM (A12-9)
    P - V
    Transponder key ECU input signal
    Ignition switch off
    Below 1 V
    Ignition switch on (IG)
    Pulse generation (see waveform 1)
    IMO (A12-10) - EOM (A12-9)
    LG - V
    Transponder key ECU output signal
    Ignition switch off
    Below 1 V
    Ignition switch on (IG)
    Pulse generation (see waveform 2)
    If the result is not as specified, there may be a malfunction in the wire harness.

  2. B069241E08
    Using an oscilloscope, check the waveform 1.
    Waveform 1 (Reference): 
    Item
    Content
    Symbols (Terminal No.)
    IMI (A12-11) - EOM (A12-9)
    Tool Setting
    10 V/DIV., 500 msec./DIV.
    Condition
    Ignition switch on (IG)

  3. B069242E10
    Using an oscilloscope, check the waveform 2.
    Waveform 2 (Reference): 
    Item
    Content
    Symbols (Terminal No.)
    IMO (A12-10) - EOM (A12-9)
    Tool Setting
    10 V/DIV., 500 msec./DIV.
    Condition
    Ignition switch on (IG)


CHECK ECM (for 2AD-FHV, 2AD-FTV)
B116297E03
  1. Measure the resistance and voltage of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    EOM (A12-37) - Body ground
    V - Body ground
    Ground
    Always
    Below 1 Ω
    IMI (A12-16) - EOM (A12-37)
    P - V
    Transponder key ECU input signal
    Ignition switch off
    Below 1 V
    Ignition switch on (IG)
    Pulse generation (see waveform 1)
    IMO (A12-15) - EOM (A12-37)
    LG - V
    Transponder key ECU output signal
    Ignition switch off
    Below 1 V
    Ignition switch on (IG)
    Pulse generation (see waveform 2)
    If the result is not as specified, there may be a malfunction in the wire harness.

  2. B069241E08
    Using an oscilloscope, check the waveform 1.
    Waveform 1 (Reference): 
    Item
    Content
    Symbols (Terminal No.)
    IMI (A12-16) - EOM (A12-37)
    Tool Setting
    10 V/DIV., 500 msec./DIV.
    Condition
    Ignition switch on (IG)

  3. B069242E10
    Using an oscilloscope, check the waveform 2.
    Waveform 2 (Reference): 
    Item
    Content
    Symbols (Terminal No.)
    IMO (A12-15) - EOM (A12-37)
    Tool Setting
    10 V/DIV., 500 msec./DIV.
    Condition
    Ignition switch on (IG)

← TERMINALS OF ECU (Nov 2005 – Dec 2006)TERMINALS OF ECU (from Aug 2007) →