TERMINALS OF ECU
System information · Vehicles built from Aug 2007
Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007
| CHECK TRANSPONDER KEY AMPLIFIER |


Disconnect the E8 amplifier connector.
Measure the resistance of the wire harness side connector.
If the result is not as specified, there may be a malfunction in the wire harness.Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
AGND (E8-7) - Body ground
R - Body ground
Ground
Always
Below 1 Ω
Reconnect the E8 amplifier connector.
Measure the resistance and voltage of the connector.
If the result is not as specified, there may be a malfunction in the amplifier.Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
AGND (E8-7) - Body ground
R - Body ground
Ground
Always
Below 1 Ω
VC5 (E8-1) - AGND (E8-7)
B - R
Power source
No key is in ignition key cylinder
Below 1 V
Key inserted
4.6 to 5.4 V
CODE (E8-4) - AGND (E8-7)
P - R
Demodulated signal of key code data
No key is in ignition key cylinder
Below 1 V
Key inserted
Pulse generation (see waveform 1)
TXCT (E8-5) - AGND (E8-7)
G - R
Key code output signal
No key is in ignition key cylinder
Below 1 V
Key inserted
Pulse generation (see waveform 2)
Using an oscilloscope, check the waveform 1.

Waveform 1 (Reference): Item
Content
Symbols (Terminal No.)
CODE (E8-4) - AGND (E8-7)
Tool Setting
5 V/DIV., 20 msec./DIV.
Condition
Key inserted
Using an oscilloscope, check the waveform 2.

Waveform 2 (Reference): Item
Content
Symbols (Terminal No.)
TXCT (E8-5) - AGND (E8-7)
Tool Setting
5 V/DIV., 20 msec./DIV.
Condition
Key inserted
| CHECK TRANSPONDER KEY ECU |


Disconnect the E50 ECU connector.
Measure the voltage and resistance of the wire harness side connector.
If the result is not as specified, there may be a malfunction on the wire harness side.Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
GND (E50-16) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
+B (E50-1) - GND (E50-16)
R - W-B
Battery
Always
10 to 14 V
IG (E50-2) - GND (E50-16)
B - W-B
Ignition switch
Ignition switch off
Below 1 V
Ignition switch on (IG)
10 to 14 V
Reconnect the E50 ECU connector.
Measure the resistance and voltage of the connector.
If the result is not as specified, there may be a malfunction in the ECU.Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
AGND (E50-5) - GND (E50-16)
R - W-B
Amplifier ground circuit
Always
Below 1 Ω
EGND (E50-11) - GND (E50-16)
V - W-B
ECM ground circuit
Always
Below 1 Ω
KSW (E50-3) - GND (E50-16)
L - W-B
Unlock warning switch
No key is in ignition key cylinder
10 to 14 V
Key inserted
Below 1 V
VC5 (E50-14) - AGND (E50-5)
B - R
Power source
No key is in ignition key cylinder
Below 1 V
Key inserted
4.6 to 5.4 V
TXCT (E50-4) - AGND (E50-5)
G - R
Transponder key amplifier communication signal
No key is in ignition key cylinder
Below 1 V
Key inserted
Pulse generation (see waveform 1)
CODE (E50-15) - AGND (E50-5)
P - R
Transponder key amplifier communication signal
No key is in ignition key cylinder
Below 1 V
Key inserted
Pulse generation (see waveform 2)
EFIO (E50-13) - EGND (E50-11)
P - V
ECM output signal
Ignition switch off
Below 1 V
Ignition switch on (IG)
Pulse generation (see waveform 3)
EFII (E50-12) - EGND (E50-11)
LG - V
ECM input signal
Ignition switch off
Below 1 V
Ignition switch off
Pulse generation (see waveform 4)
IND (E50-8)- GND (E50-16)
Y - W-B
Security indicator light signal
Engine immobiliser system SET
3 to 5 V
Engine immobiliser system UNSET
Below 1 V
D (E50-9) - GND (E50-16)
W - W-B
Diagnosis tester communication
Ignition switch on
Pulse generation
Using an oscilloscope, check the waveform 1.

Waveform 1 (Reference): Item
Content
Symbols (Terminal No.)
TXCT (E50-4) - AGND (E50-5)
Tool Setting
5 V/DIV., 20 msec./DIV.
Condition
Key inserted
Using an oscilloscope, check the waveform 2.

Waveform 2 (Reference): Item
Content
Symbols (Terminal No.)
CODE (E50-15) - AGND (E50-5)
Tool Setting
5 V/DIV., 20 msec./DIV.
Condition
Key inserted
Using an oscilloscope, check the waveform 3.

Waveform 3 (Reference): Item
Content
Symbols (Terminal No.)
EFIO (E50-13) - EGND (E50-11)
Tool Setting
10 V/DIV., 500 msec./DIV.
Condition
Ignition switch on (IG)
Using an oscilloscope, check the waveform 4.

Waveform 4 (Reference): Item
Content
Symbols (Terminal No.)
EFII (E50-12) - EGND (E50-11)
Tool Setting
10 V/DIV., 500 msec./DIV.
Condition
Ignition switch on (IG)
| CHECK ECM (for 1AZ-FE, 2AZ-FE, 2GR-FE) |


Measure the resistance and voltage of the wire harness side connector.
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
EOM (A12-9) - Body ground
V - Body ground*1
W-B - Body ground*2
Ground
Always
Below 1 Ω
IMI (A12-11) - EOM (A12-9)
P - V*1
P - W-B*2
Transponder key ECU input signal
Ignition switch off
Below 1 V
Ignition switch on (IG)
Pulse generation (see waveform 1)
IMO (A12-10) - EOM (A12-9)
LG - V*1
LG - W-B*2
Transponder key ECU output signal
Ignition switch off
Below 1 V
Ignition switch on (IG)
Pulse generation (see waveform 2)
- HINT:
- *1: for 1AZ-FE, 2AZ-FE
- *2: for 2GR-FE
- *1: for 1AZ-FE, 2AZ-FE
Using an oscilloscope, check the waveform 1.

Waveform 1 (Reference): Item
Content
Symbols (Terminal No.)
IMI (A12-11) - EOM (A12-9)
Tool Setting
10 V/DIV., 500 msec./DIV.
Condition
Ignition switch on (IG)
Using an oscilloscope, check the waveform 2.

Waveform 2 (Reference): Item
Content
Symbols (Terminal No.)
IMO (A12-10) - EOM (A12-9)
Tool Setting
10 V/DIV., 500 msec./DIV.
Condition
Ignition switch on (IG)
| CHECK ECM (for 2AD-FHV, 2AD-FTV) |


Measure the resistance and voltage of the wire harness side connector.
If the result is not as specified, there may be a malfunction in the wire harness.Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
EOM (A12-37) - Body ground
V - Body ground
Ground
Always
Below 1 Ω
IMI (A12-16) - EOM (A12-37)
P - V
Transponder key ECU input signal
Ignition switch off
Below 1 V
Ignition switch on (IG)
Pulse generation (see waveform 1)
IMO (A12-15) - EOM (A12-37)
LG - V
Transponder key ECU output signal
Ignition switch off
Below 1 V
Ignition switch on (IG)
Pulse generation (see waveform 2)
Using an oscilloscope, check the waveform 1.

Waveform 1 (Reference): Item
Content
Symbols (Terminal No.)
IMI (A12-16) - EOM (A12-37)
Tool Setting
10 V/DIV., 500 msec./DIV.
Condition
Ignition switch on (IG)
Using an oscilloscope, check the waveform 2.

Waveform 2 (Reference): Item
Content
Symbols (Terminal No.)
IMO (A12-15) - EOM (A12-37)
Tool Setting
10 V/DIV., 500 msec./DIV.
Condition
Ignition switch on (IG)