Front Passenger Side Door Entry Unlock Function does not Operate
Circuit diagnosis · Vehicles built from Nov 2005
DESCRIPTION
- for LHD
When an ID code from the door electrical key oscillator RH matches the ID code from the key, the certification ECU outputs an SEL signal (Lo when output) to the door electrical key oscillator RH, activates the touch sensor located on the backside of the outside door handle, and enters unlock standby mode. When the touch sensor is touched, the door electrical key oscillator RH sends a SENS signal (Lo when output) to the certification ECU and the certification ECU sends an unlock signal to the front passenger side door lock.
- for RHD
When an ID code from the door electrical key oscillator LH matches the ID code from the key, the certification ECU outputs an SEL signal (Lo when output) to the door electrical key oscillator LH, activates the touch sensor located on the backside of the outside door handle, and enters unlock standby mode. When the touch sensor is touched, the door electrical key oscillator LH sends a SENS signal (Lo when output) to the certification ECU and the certification ECU sends an unlock signal to the front passenger side door lock.
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK FOR DTC |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
By following the tester screen display, check whether any DTCs are output.
- OK:
- No DTC output.
|
|
||||
| OK | |
| 2. CHECK MANUAL DOOR UNLOCK OPERATION |
Check that all the doors unlock when the door control switch (for manual operation) is turned to UNLOCK.
- OK:
- All doors can be unlocked with door control switch.
|
|
||||
| OK | |
| 3. CHECK WIRELESS DOOR LOCK CONTROL OPERATION |
Check that the wireless door lock and unlock functions operates normally (Click here).
- OK:
- Wireless door lock and unlock functions operate normally.
|
|
||||
| OK | |
| 4. READ VALUE USING INTELLIGENT TESTER (DOOR COURTESY LIGHT SWITCH) |
Check the Data List for proper functioning of the door courtesy light switch (passenger side).
Main body ECU: Item
Measurement Item / Range (Display)
Normal Condition
Diagnostic Note
P Door Courtesy SW
Passenger side courtesy light switch signal / ON or OFF
ON: Passenger side door is open
OFF: Passenger side door is closed
-
- OK:
- On tester screen, item changes between ON and OFF according to above chart.
|
|
||||
| OK | |
| 5. READ VALUE USING INTELLIGENT TESTER (LOCK POSITION SWITCH) |
Check the Data List for proper functioning of the door lock position switch (passenger side).
Main body ECU: Item
Measurement Item / Range (Display)
Normal Condition
Diagnostic Note
P-Door Lock Pos SW
Passenger side door unlock detection switch signal / ON or OFF
ON: Door is unlocked
OFF: Door is locked
-
- OK:
- On tester screen, item changes between ON and OFF according to above chart.
|
|
||||
| OK | |
| 6. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FRONT PASSENGER SIDE SELECT) |
Select the Active Test, use the intelligent tester to generate a control command, and then check that the door electrical key oscillator operates.
Certification ECU: Item
Test Details
Diagnostic Note
P-Seat Select
Passenger side electrical key oscillator ON / OFF
-
- OK:
- ON (P-Seat Select is ON) appears on screen.
|
|
||||
| OK | |
| 7. READ VALUE USING INTELLIGENT TESTER (TOUCH SENSOR) |
With "P-Seat Select" ON, check the Data List to confirm the operation of the touch sensor.
Certification ECU: Item
Measurement Item / Range (Display)
Normal Condition
Diagnostic Note
P-Door Touch Sensor
Front passenger side door touch sensor / ON or OFF
ON: Sensor is touched
OFF: Sensor is not touched
-
- OK:
- When passenger side door touch sensor is set to ON, ON (sensor is touched) appears on screen.
|
|
||||
| OK | |
| 8. CHECK ECU AGGREGATION BOX (OPERATION) |
Temporarily replace the ECU aggregation box (certification ECU) with a new or normally functioning one.
Check that the entry unlock function operates normally (Click here).
- OK:
- Entry unlock function operates normally.
|
|
||||
| OK | ||
| ||
| 9. CHECK DOOR ELECTRICAL KEY OSCILLATOR (for Passenger Side) |
![]() ![]() |
Measure the voltage of the oscillator.
- Standard voltage:
Tester Connection
Condition
Specified Condition
4 (SEL) - Body ground
During Active Test
Below 1 V
6 (SENS) - Body ground
Touch sensor is touched during Active Test
Below 1 V
Touch sensor is not touched during Active Test
10 to 14 V
|
|
||||
| NG | |
| 10. CHECK WIRE HARNESS (DOOR ELECTRICAL KEY OSCILLATOR - ELECTRICAL KEY ANTENNA) |
![]() ![]() |
Disconnect the Y2*1 or Z2*2 oscillator connector.
Disconnect the Y1*1 or Z1*2 antenna connector.
Measure the resistance of the wire harness side connectors.
- HINT:
- *1: for LHD
- *2: for RHD
- Standard resistance:
- for LHD:
Tester Connection
Specified Condition
Y2-2 (SGT) - Y1-6 (SGT)
Below 1 Ω
Y2-3 (ANT1) - Y1-5 (ANT1)
Y2-8 (ANT2) - Y1-2 (ANT2)
Y2-9 (TRG-) - Y1-1 (TRG-)
Y2-2 (SGT) or Y1-6 (SGT) - Body ground
10 kΩ or higher
Y2-3 (ANT1) or Y1-5 (ANT1) - Body ground
Y2-8 (ANT2) or Y1-2 (ANT2) - Body ground
Y2-9 (TRG-) or Y1-1 (TRG-) - Body ground
- for RHD:
Tester Connection
Specified Condition
Z2-2 (SGT) - Z1-6 (SGT)
Below 1 Ω
Z2-3 (ANT1) - Z1-5 (ANT1)
Z2-8 (ANT2) - Z1-2 (ANT2)
Z2-9 (TRG-) - Z1-1 (TRG-)
Z2-2 (SGT) or Z1-6 (SGT) - Body ground
10 kΩ or higher
Z2-3 (ANT1) or Z1-5 (ANT1) - Body ground
Z2-8 (ANT2) or Z1-2 (ANT2) - Body ground
Z2-9 (TRG-) or Z1-1 (TRG-) - Body ground
|
|
||||
| OK | |
| 11. CHECK WIRE HARNESS (CERTIFICATION ECU - DOOR ELECTRICAL KEY OSCILLATOR) |
![]() ![]() |
Disconnect the E63 ECU connector.
Disconnect the Y2*1 or Z2*2 oscillator connector.
Measure the resistance of the wire harness side connectors.
- HINT:
- *1: for LHD
- *2: for RHD
- Standard resistance:
- for LHD:
Tester Connection
Specified Condition
E63-6 (SEL2) - Y2-4 (SEL)
Below 1 Ω
E63-23 (SEN2) - Y2-6 (SEN2)
E63-35 (CLG2) - Y2-10 (CLG)
E63-36 (DG2B) - Y2-5 (CLGB)
E63-6 (SEL2) or Y2-4 (SEL) - Body ground
10 kΩ or higher
E63-23 (SEN2) or Y2-6 (SEN2) - Body ground
E63-35 (CLG2) or Y2-10 (CLG) - Body ground
E63-36 (DG2B) or Y2-5 (CLGB) - Body ground
- for RHD:
Tester Connection
Specified Condition
E63-6 (SEL2) - Z2-4 (SEL)
Below 1 Ω
E63-23 (SEN2) - Z2-6 (SEN2)
E63-35 (CLG2) - Z2-10 (CLG)
E63-36 (DG2B) - Z2-5 (CLGB)
E63-6 (SEL2) or Z2-4 (SEL) - Body ground
10 kΩ or higher
E63-23 (SEN2) or Z2-6 (SEN2) - Body ground
E63-35 (CLG2) or Z2-10 (CLG) - Body ground
E63-36 (DG2B) or Z2-5 (CLGB) - Body ground
|
|
||||
| OK | ||
| ||



