Driver Side Door Entry Lock and Unlock Functions do not Operate
Circuit diagnosis · Vehicles built from Nov 2005
DESCRIPTION
Neither the entry lock nor unlock functions operate when: 1) nothing is output from the door electrical key oscillator (driver side), 2) the entry and start system is disabled through customization, or 3) the entire power door lock control system is malfunctioning.WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK FOR DTC |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
By following the tester screen display, check whether any DTCs are output.
- OK:
- No DTC output.
|
|
||||
| OK | |
| 2. CHECK MANUAL DOOR LOCK AND UNLOCK OPERATION |
Check that all the doors lock when the door control switch (for manual operation) is turned to LOCK and all doors unlock when turned to UNLOCK.
- OK:
- All doors can be locked and unlocked with door control switch.
|
|
||||
| OK | |
| 3. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DOOR ELECTRICAL KEY OSCILLATOR) |
Select the Active Test, use the intelligent tester to generate a control command, and then check that the oscillator operates.
Certification ECU: Item
Test Details
Diagnostic Note
D-Seat Outside Transmitter
Driver side door electrical key oscillator ON / OFF
-
- OK:
- When key is brought close to door oscillator that is ON, indicator light on key illuminates.
|
|
||||
| NG | |
| 4. CHECK WIRE HARNESS (CERTIFICATION ECU - DOOR ELECTRICAL KEY OSCILLATOR) |
![]() ![]() |
Disconnect the E63 ECU connector.
Disconnect the Z2*1 or Y2*2 oscillator connector.
Measure the resistance of the wire harness side connectors.
- HINT:
- *1: for LHD
- *2: for RHD
- Standard resistance:
- for LHD:
Tester Connection
Specified Condition
E63-33 (CLG1) - Z2-10 (CLG)
Below 1 Ω
E63-34 (CG1B) - Z2-5 (CLGB)
E63-33 (CLG1) or Z2-10 (CLG) - Body ground
10 kΩ or higher
E63-34 (CG1B) or Z2-5 (CLGB) - Body ground
- for RHD:
Tester Connection
Specified Condition
E63-33 (CLG1) - Z2-10 (CLG)
Below 1 Ω
E63-34 (CG1B) - Z2-5 (CLGB)
E63-33 (CLG1) or Z2-10 (CLG) - Body ground
10 kΩ or higher
E63-34 (CG1B) or Z2-5 (CLGB) - Body ground
|
|
||||
| OK | |
| 5. CHECK WIRE HARNESS (DOOR ELECTRICAL KEY OSCILLATOR - DOOR ELECTRICAL KEY ANTENNA) |
![]() ![]() |
Disconnect the Z2*1 or Y2*2 oscillator connector.
Disconnect the Z1*1 or Y1*2 antenna connector.
Measure the resistance of the wire harness side connectors.
- HINT:
- *1: for LHD
- *2: for RHD
- Standard resistance:
- for LHD:
Tester Connection
Specified Condition
Z2-2 (SGT) - Z1-6 (SGT)
Below 1 Ω
Z2-3 (ANT1) - Z1-5 (ANT1)
Z2-8 (ANT2) - Z1-2 (ANT2)
Z2-9 (TRG-) - Z1-1 (TRG-)
Z2-2 (SGT) or Z1-6 (SGT) - Body ground
10 kΩ or higher
Z2-3 (ANT1) or Z1-5 (ANT1) - Body ground
Z2-8 (ANT2) or Z1-2 (ANT2) - Body ground
Z2-9 (TRG-) or Z1-1 (TRG-) - Body ground
- for RHD:
Tester Connection
Specified Condition
Y2-2 (SGT) - Y1-6 (SGT)
Below 1 Ω
Y2-3 (ANT1) - Y1-5 (ANT1)
Y2-8 (ANT2) - Y1-2 (ANT2)
Y2-9 (TRG-) - Y1-1 (TRG-)
Y2-2 (SGT) or Y1-6 (SGT) - Body ground
10 kΩ or higher
Y2-3 (ANT1) or Y1-5 (ANT1) - Body ground
Y2-8 (ANT2) or Y1-2 (ANT2) - Body ground
Y2-9 (TRG-) or Y1-1 (TRG-) - Body ground
|
|
||||
| OK | |
| 6. CHECK WIRE HARNESS (DOOR ELECTRICAL KEY OSCILLATOR - BATTERY AND BODY GROUND) |
![]() ![]() |
Disconnect the Z2*1 or Y2*2 oscillator connector.
Measure the resistance and voltage of the wire harness side connector.
- HINT:
- *1: for LHD
- *2: for RHD
- Standard resistance:
- for LHD:
Tester Connection
Specified Condition
Z2-7 (GND) - Body ground
Below 1 Ω
- for RHD:
Tester Connection
Specified Condition
Y2-7 (GND) - Body ground
Below 1 Ω
- Standard voltage:
- for LHD:
Tester Connection
Specified Condition
Z2-1 (+B) - Body ground
10 to 14 V
- for RHD:
Tester Connection
Specified Condition
Y2-1 (+B) - Body ground
10 to 14 V
|
|
||||
| OK | |
| 7. CHECK WIRE HARNESS (DOOR ELECTRICAL KEY ANTENNA - CERTIFICATION ECU) |
![]() ![]() |
Disconnect the Z1*1 or Y1*2 antenna connector.
Disconnect the E63 ECU connector.
Measure the resistance of the wire harness side connectors.
- HINT:
- *1: for LHD
- *2: for RHD
- Standard resistance:
- for LHD:
Tester Connection
Specified Condition
Z1-3 (TRG+) - E63-3 (TSW1)
Below 1 Ω
Z1-3 (TRG+) or E63-3 (TSW1) - Body ground
10 kΩ or higher
- for RHD:
Tester Connection
Specified Condition
Y1-3 (TRG+) - E63-3 (TSW1)
Below 1 Ω
Y1-3 (TRG+) or E63-3 (TSW1) - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 8. CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (OPERATION) |
Temporarily replace the front door outside handle (electrical key antenna) with a new or normally functioning one.
Check that the entry lock and unlock functions operate normally (Click here).
- OK:
- Entry lock and unlock functions operate normally.
|
|
||||
| NG | |
| 9. CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION) |
Temporarily replace the door electrical key oscillator (driver side) with a new or normally functioning one.
Check that the entry lock and unlock functions operate normally.
- OK:
- Entry lock and unlock functions operate normally.
|
|
||||
| OK | ||
| ||




