TERMINALS OF ECU
System information · Vehicles built from Nov 2005
| CHECK AUTO WIPER RELAY |


Disconnect the E66 relay connector.
Measure the voltage and resistance of the wire harness side connector.
If the result is not as specified, there may be a malfunction on the wire harness side.Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
IG (E66-12) - Body ground
L - Body ground
IG signal circuit
Ignition switch on (IG)
10 to 14 V
Ignition switch off
Below 1 V
WIG (E66-23) - Body ground
L - Body ground
WIG signal circuit
Ignition switch on (IG)
10 to 14 V
Ignition switch off
Below 1 V
W (E66-4) - Body ground
W - Body ground
Front washer switch circuit
Front washer switch is ON
Below 1 Ω
Front washer switch is OFF
10 kΩ or higher
E (E66-26) - Body ground
W-B - Body ground
Body ground
Always
Below 1 Ω
Reconnect the E66 relay connector.
Measure the voltage of the connector.
If the result is not as specified, the ECU may have a malfunction.Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
+2S (E66-1) - Body ground
B - Body ground
Front wiper LO speed signal circuit
Ignition switch on (IG),
front wiper switch LO
10 to 14 V
Ignition switch on (IG),
front wiper switch except LO
Below 1 V
+2 (E66-3) - Body ground
R - Body ground
Front wiper motor HI speed signal circuit
Front wiper motor is in HI operation
10 to 14 V
Front wiper motor is OFF
Below 1 V
C1 (E66-17) - C0 (E66-16)
O - L
IG signal circuit
Ignition switch on (IG)
10 to 14 V
Ignition switch off
Below 1 V
W (E66-4) - Body ground
W - Body ground
Front washer motor circuit
Front washer switch is ON
Below 1 V
Front washer switch is OFF
10 to 14 V
+1 (E66-2) - Body ground
B - Body ground
Front wiper motor LO speed signal circuit
Front wiper motor is in LO operation
10 to 14 V
Front wiper motor is OFF
Below 1 V
+SM (E66-10) - Body ground
G- Body ground
Front wiper motor operation signal
Front wiper motor is in LO or HI operation
10 to 14 V
Front wiper motor is OFF
Below 1 V
| CHECK HEADLIGHT CLEANER CONTROL RELAY |


Disconnect the A44 relay connector.
Measure the voltage and resistance of the wire harness side connector.
If the result is not as specified, there may be a malfunction on the wire harness side.Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
IG (A44-3) - Body ground
L - Body ground
IG signal circuit
Ignition switch on (IG)
10 to 14 V
Ignition switch off
Below 1 V
E (A44-4) - Body ground
W-B - Body ground
Body ground
Always
Below 1 Ω
Reconnect the A44 relay connector.
Measure the voltage of the connector.
If the result is not as specified, the relay may have a malfunction.Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
HDLO (A44-1) - Body ground
BR - Body ground
Headlight LO signal
Headlight control switch LO
10 to 14 V
Headlight control switch except LO
Below 1 V
H (A44-2) - Body ground
R - Body ground
Headlight cleaner switch signal
Headlight cleaner switch ON,
headlight control switch LO
10 to 14 V
Headlight cleaner switch ON,
headlight control switch except LO
Below 1 V
PB (A44-6) - Body ground
B - Body ground
Headlight cleaner motor signal
Headlight cleaner switch ON,
headlight control switch except LO
10 to 14 V
Headlight cleaner switch ON,
headlight control switch LO
Below 1 V