2005-2008 RAV4 · Service Manual DRIVE LINE

DISASSEMBLY

Removal / installation · Vehicles built from Nov 2005


1. REMOVE TRANSFER & TRANSAXLE SETTING STUD BOLT

C126625
  1. Remove the stud bolt.


2. REMOVE TRANSFER CASE STRAIGHT PIN

C127246E01
  1. Remove the 2 straight pins.


3. REMOVE TRANSFER CASE NO. 1 PLUG
  1. Remove the No. 1 plug.

  1. Remove the gasket from the No. 1 plug.


4. REMOVE TRANSFER CASE NO. 2 PLUG

C126626E01
  1. Remove the No. 2 plug.

  1. Remove the gasket from the No. 2 plug.


5. REMOVE TRANSFER DRAIN PLUG

C126627E01
  1. Remove the drain plug.

  1. Remove the gasket from the drain plug.


6. REMOVE TRANSFER CASE OIL SEAL LH

C126628E01
  1. Using SST, tap out the oil seal from the case.

    SST
    09308-00010  

    NOTICE:
    Do not damage the oil seal lip.


7. REMOVE TRANSFER CASE OIL SEAL RH

C126629
  1. Using SST, tap out the oil seal from the case.

    SST
    09308-00010  

    NOTICE:
    Do not damage the oil seal lip.


8. INSPECT RING GEAR BACKLASH

C126630E01
  1. Using a dial indicator, measure the backlash of the ring gear at 3 points.

    Standard backlash:
    0.10 to 0.20 mm (0.0039 to 0.0079 in.)

    If the backlash is not within the specified range, adjust the backlash or repair as necessary.


9. REMOVE NO. 1 TRANSFER CASE COVER

  1. C126631
    Remove the 8 bolts.

  1. C126632
    Using a brass bar and hammer, tap out the cover from the case.


10. REMOVE TRANSFER RING GEAR

C126633
  1. Remove the ring gear from the transfer case.


11. REMOVE TRANSFER CASE STRAIGHT PIN
  1. Remove the 2 straight pins from the transfer case.


12. REMOVE TRANSFER OUTPUT REAR SHAFT SUB-ASSEMBLY

C126635
  1. Remove the 5 bolts and transfer output rear shaft.

  1. C109626E01
    Using SST and a hammer, unstake the lock nut.
    SST
    09930-00010  

  1. Remove the lock nut.


13. REMOVE TRANSFER DRIVEN PINION

C109627E01
  1. Using SST and a press, press out the driven pinion from the output shaft.

    SST
    09950-00020  
    09950-60010   (09951-00220)
    09950-70010   (09951-07100)


14. REMOVE TRANSFER OUTPUT REAR SHAFT DUST DEFLECTOR

  1. C109629E01
    Using SST and a press, press out the dust deflector from the output rear shaft.


15. REMOVE TRANSFER DRIVEN PINION FRONT BEARING

C109628E02
  1. Using SST and a press, press out the driven pinion from the bearing.

    SST
    09950-00020  
    09950-60010   (09951-00220)
    09950-70010   (09951-07100)

  1. C109630
    Remove the O-ring from the bearing.


16. REMOVE TRANSFER OUTPUT SHAFT WASHER

C110759
  1. Remove the washer from the transfer pinion gear.


17. REMOVE RING GEAR MOUNTING CASE BEARING (for LH side)

C109631E01
  1. Using SST, remove the bearing from the mounting case.

    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
    09950-60010   (09951-00540)

  1. C109633E01
    Using SST and a hammer, tap out the bearing.
    SST
    09310-35010  


18. REMOVE RING GEAR MOUNTING CASE WASHER

19. REMOVE RING GEAR MOUNTING CASE BEARING (for RH side)

C109632
  1. Using SST, remove the bearing from the mounting case.

    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
    09950-60010   (09951-00540)

  1. Using SST and a hammer, tap out the bearing (race) from the cover.

    SST
    09636-20010  


20. REMOVE TRANSFER RING GEAR MOUNTING CASE NO. 2 WASHER

21. REMOVE SHAFT SNAP RING

C109636
  1. Using a snap ring expander, remove the snap ring.


22. REMOVE TRANSFER RING GEAR MOUNTING CASE

C109637E01
  1. Using SST and a press, press out the ring gear from the mounting case.

    SST
    09950-60010   (09951-00400)


23. REMOVE BREATHER OIL DEFLECTOR

C109640
  1. Remove the 2 bolts and oil deflector.


24. REMOVE TRANSFER CASE BREATHER PLUG

C109638
  1. Remove the breather plug from the transfer case.

← REMOVAL (from Aug 2007)REASSEMBLY (Nov 2005 – Dec 2006) →