2005-2008 RAV4 · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built Aug 2007 – Jul 2008

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 Aug 2007 – Jul 2008 from Aug 2008


1. INSTALL ABS AND TRACTION ACTUATOR ASSEMBLY WITH BRACKET

NOTICE:
Do not remove the hole plug before connecting the brake tube. New actuators are filled with brake fluid.

  1. C127318E01
    Install the actuator with bracket with the 3 nuts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

    HINT:
    The nuts should be tightened in order from 1 to 3 as shown in the illustration.

    NOTICE:
    Be careful not to damage the brake tubes.

  1. C128743
    Connect the brake tube clamp to the bracket.

  1. C128530
    Connect the connector and push the lock lever downward.


2. CONNECT BRAKE LINES

  1. C127316E01
    Using SST, connect the 6 brake lines to the correct locations on the actuator, as shown in the illustration.
    SST
    09023-00101  

    Torque:
    15.2 N*m{ 155 kgf*cm , 11 ft.*lbf } without SST
    14 N*m{ 144 kgf*cm , 10 ft.*lbf } with SST

    HINT:
    Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).


3. FILL RESERVOIR WITH BRAKE FLUID

  1. C126432
    Set the brake fluid can upside down on the reservoir.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3

    NOTICE:
    1. Make sure there is sufficient brake fluid in the can.
    2. After adding braking fluid, make sure the reservoir is sufficiently full.


4. BLEED AIR FROM BRAKE MASTER CYLINDER

C126433

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed air from the master cylinder.

  1. Using SST, disconnect the 2 brake lines from the master cylinder.

    SST
    09023-00101  

  1. Slowly depress and hold the brake pedal.

  1. C126434
    Block the outer holes with your fingers, and release the pedal.

  1. Repeat the 2 previous steps 3 or 4 times.

  1. Using SST, connect the 2 brake lines to the master cylinder.

    SST
    09023-00101  

    Torque:
    15.2 N*m{ 155 kgf*cm , 11 ft.*lbf } without SST
    14 N*m{ 144 kgf*cm , 10 ft.*lbf } with SST

    HINT:
    Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).


5. BLEED AIR FROM BRAKE LINE

C126435E01
  1. Remove the bleeder plug cap.

  1. Connect the vinyl tube to the bleeder plugs.

  1. Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.

  1. Repeat the 2 previous steps until all the air in the brake fluid is gone.

  1. Tighten the bleeder plug.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

  1. Install the cap.

  1. Bleed air from the brake line for each wheel by repeating the above procedures.


6. BLEED AIR FROM ABS AND TRACTION ACTUATOR ASSEMBLY

NOTICE:
After bleeding the air from the brake system, if the height or feel of the brake pedal cannot be obtained, perform air bleeding of the brake actuator with an intelligent tester by following the procedure below.

  1. Depress the brake pedal more than 20 times with the engine off.

  1. B127990E01
    Connect the intelligent tester to the DLC3, and turn the ignition switch on (IG).

    NOTICE:
    Do not start the engine.

  1. Select AIR BLEEDING on the intelligent tester.

    HINT:
    Refer to the intelligent tester operator's manual for further details.

  1. Bleed the air out of the suction line.

    NOTICE:
    1. Perform the bleeding at the right front wheel and right rear wheel.
    2. Bleed the air by following the steps displayed on the intelligent tester.


    1. Connect a vinyl tube to the bleeder plug at the right front wheel or the right rear wheel.

    2. Loosen the bleeder plug.

    3. Operate the brake actuator to bleed the air using the intelligent tester.

      NOTICE:
      Release the brake pedal at this time.

      HINT:
      This operation stops automatically after 4 seconds.

    4. Check if the operation has stopped by referring to the intelligent tester display.

    5. Temporarily tighten the bleeder plug.

    6. Repeat the 4 previous steps until all air in the fluid is completely bled out.

    7. Tighten the bleeder plug.

      Torque:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

    8. Repeat all of the above procedures for the right rear wheel to bleed the air out of the suction line.

  1. Bleed the air out of the pressure reduction line.

    NOTICE:
    1. Perform the bleeding at the 4 wheels.
    2. Bleed the air by following the steps displayed on the intelligent tester.


    1. Connect a vinyl tube to either one of the bleeder plugs.

    2. Loosen the bleeder plug.

    3. Using the intelligent tester, operate the brake actuator assembly, completely depress the brake pedal and hold it there.

      NOTICE:
      1. During this procedure, the pedal will feel heavy, but completely depress it so that the brake fluid comes out of the bleeder plug.
      2. Hold the brake pedal depressed. Do not depress and release the pedal repeatedly.

      HINT:
      The operation stops automatically after 4 seconds. When performing this procedure continuously, set an interval of at least 20 seconds.

    4. Tighten the bleeder plug, then release the brake pedal.

    5. Repeat the 3 previous steps until all air in the fluid is completely bled out.

    6. Tighten the bleeder plug.

      Torque:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

    7. Repeat all of the above procedures for the other wheels to bleed the air out of the pressure reduction line.


7. BLEED AIR FROM CLUTCH LINE (for Manual Transaxle)
  1. Fill the brake reservoir with brake fluid and bleed the clutch system.

    Torque:
    8.3 N*m{ 85 kgf*cm , 74 in.*lbf }


8. CHECK BRAKE FLUID LEVEL IN RESERVOIR

C126431
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3

    HINT:
    Add fluid to a level between the reservoir's MIN and MAX lines.


9. CHECK FOR BRAKE FLUID LEAKAGE

10. INSTALL AIR CLEANER BRACKET (for 2AD-FHV)
  1. Install the air cleaner bracket (Click here).

    HINT:
    Refer to the procedures from the installation of the air cleaner bracket up until the installation of the air cleaner cap sub-assembly.


11. INSTALL AIR CLEANER BRACKET (for 2AD-FTV)
  1. Install the air cleaner bracket (Click here).

    HINT:
    Refer to the procedures from the installation of the air cleaner bracket up until the installation of the air cleaner cap sub-assembly.


12. INSTALL AIR CLEANER CASE SUB-ASSEMBLY (for 2GR-FE)

  1. A137898
    Install the air cleaner case with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the harness clamp.


13. INSTALL AIR CLEANER CASE SUB-ASSEMBLY (for 2AZ-FE)
  1. Install the air cleaner case (Click here).

    HINT:
    Refer to the procedures from the installation of the air cleaner case up until the installation of the purge VSV.


14. INSTALL AIR CLEANER CASE SUB-ASSEMBLY (for 1AZ-FE)
  1. Install the air cleaner case (Click here).

    HINT:
    Refer to the procedures from the installation of the air cleaner case up until the installation of the purge VSV.


15. INSTALL AIR CLEANER CAP SUB-ASSEMBLY (for 2GR-FE)
  1. Install the air cleaner filter element onto the air cleaner case.

  1. A137901E01
    Insert the hinge part of the air cleaner cap into the air cleaner case, then hang the 2 hook clamps.

  1. A173728
    Tighten the No. 1 air cleaner hose clamp.

  1. Connect the No. 2 ventilation hose to the air cleaner hose.

  1. Connect the 2 wire harness clamps and 2 vacuum hoses.

  1. Connect the VSV (intake air control) connector.

  1. Connect the mass air flow meter connector.


16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

17. CHECK ABS AND TRACTION ACTUATOR ASSEMBLY WITH INTELLIGENT TESTER
  1. Check the ABS and traction actuator with the intelligent tester (Click here).

← INSTALLATION (Jan 2007 – Jul 2007)INSTALLATION (from Aug 2008) →