2005-2008 RAV4 · Service Manual BODY ELECTRICAL

INSPECTION

Inspection · Vehicles built from Nov 2005


INSPECT FRONT DOOR WITH MOTOR LOCK ASSEMBLY (for Driver Side)

  1. for LHD:

    1. E123888E01
      Apply the battery voltage to the motor terminals and check the operation of the door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 4 (L)
      Battery negative (-) → 1 (UL)
      Lock
      Battery positive (+) → 1 (UL)
      Battery negative (-) → 4 (L)
      Unlock

      1. If the result is not as specified, replace the door lock assembly.

    2. Measure the resistance of the door lock position switch.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      8 (LSSR) - 7 (E)
      Lock
      10 kΩ or higher
      8 (LSSR) - 7 (E)
      Unlock
      Below 1 Ω

      1. If the result is not as specified, replace the door lock assembly.

    3. B112017E02
      Measure the resistance of the door key lock and unlock switch operation.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      9 (L) - 7 (E)
      Lock
      Below 1 Ω
      9 (L) - 7 (E)
      OFF
      10 kΩ or higher
      10 (UL) - 7 (E)
      Unlock
      Below 1 Ω
      10 (UL) - 7 (E)
      OFF
      10 kΩ or higher

      1. If the result is not as specified, replace the door lock assembly.

  1. E123889E02
    for RHD (w/o Double Locking System):

    1. Apply the battery voltage to the motor terminals and check the operation of the door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 4 (L)
      Battery negative (-) → 1 (UL)
      Lock
      Battery positive (+) → 1 (UL)
      Battery negative (-) → 4 (L)
      Unlock

      1. If the result is not as specified, replace the door lock assembly.

    2. Measure the resistance of the position switch.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      7 (LSSR) - 8 (E)
      Lock
      10 kΩ or higher
      7 (LSSR) - 8 (E)
      Unlock
      Below 1 Ω

      1. If the result is not as specified, replace the door lock assembly.

    3. B117135E02
      Measure the resistance of the door lock and unlock switch.

      Standard resistance:
      Measurement Condition
      Switch Condition
      Specified Condition
      5 (UL) -8 (E)
      Lock
      Below 1 Ω
      5 (UL) -8 (E)
      OFF
      10 kΩ or higher
      6 (L) - 8 (E)
      Unlock
      Below 1 Ω
      6 (L) - 8 (E)
      OFF
      10 kΩ or higher

      1. If the result is not as specified, replace the door lock assembly.

  1. E123913E03
    for RHD (w/ Double Locking System):

    1. Apply the battery voltage to the motor terminals and check the operation of the door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 2 (L)
      Battery negative (-) → 1 (UL)
      Lock
      Battery positive (+) → 1 (UL)
      Battery negative (-) → 2 (L)
      Unlock

      1. If the result is not as specified, replace the door lock assembly.

    2. Measure the resistance of the position switch.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      7 (LSSR) - 8 (E)
      Lock
      10 kΩ or higher
      7 (LSSR) - 8 (E)
      Unlock
      Below 1 Ω

      1. If the result is not as specified, replace the door lock assembly.

    3. E123940E01
      Measure the resistance of the door lock and unlock switch.

      Standard resistance:
      Measurement Condition
      Switch Condition
      Specified Condition
      5 (UL) -8 (E)
      Lock
      Below 1 Ω
      5 (UL) -8 (E)
      OFF
      10 kΩ or higher
      6 (L) - 8 (E)
      Unlock
      Below 1 Ω
      6 (L) - 8 (E)
      OFF
      10 kΩ or higher

      1. If the result is not as specified, replace the door lock assembly.


INSPECT FRONT DOOR WITH MOTOR LOCK ASSEMBLY (for Passenger Side)

  1. for LHD:

    1. E123889E02
      Apply the battery voltage to the door lock motor and check the operation of the door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 4 (L)
      Battery negative (-) → 1 (UL)
      Lock
      Battery positive (+) → 1 (UL)
      Battery negative (-) → 4 (L)
      Unlock

      1. If the result is not as specified, replace the door lock assembly.

    2. Measure the resistance of the door lock position switch.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      7 (LSSR) - 8 (E)
      Lock
      10 kΩ or higher
      7 (LSSR) - 8 (E)
      Unlock
      Below 1 Ω

      1. If the result is not as specified, replace the door lock assembly.

  1. E123888E01
    for RHD (w/o Double Locking System):

    1. Apply the battery voltage to the door lock motor and check the operation of the door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 4 (L)
      Battery negative (-) → 1 (UL)
      Lock
      Battery positive (+) → 1 (UL)
      Battery negative (-) → 4 (L)
      Unlock

      1. If the result is not as specified, replace the door lock assembly.

    2. Measure the resistance of the door lock position switch.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      8 (LSSR) - 7 (E)
      Lock
      10 kΩ or higher
      8 (LSSR) - 7 (E)
      Unlock
      Below 1 Ω

      1. If the result is not as specified, replace the door lock assembly.

  1. E123912E04
    for RHD (w/ Double Locking System):

    1. Apply the battery voltage to the door lock motor and check the operation of the door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 4 (L)
      Battery negative (-) → 3 (UL)
      Lock
      Battery positive (+) → 3 (UL)
      Battery negative (-) → 4 (L)
      Unlock

      1. If the result is not as specified, replace the door lock assembly.

    2. Measure the resistance of the door lock position switch.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      8 (LSSR) - 7 (E)
      Lock
      10 kΩ or higher
      8 (LSSR) - 7 (E)
      Unlock
      Below 1 Ω

      1. If the result is not as specified, replace the door lock assembly.

← INSPECTION (from Nov 2005)INSPECTION (from Nov 2005) →