2005-2008 RAV4 · Service Manual BODY ELECTRICAL

Door Courtesy Switch Circuit

Circuit diagnosis · Vehicles built from Nov 2005

DESCRIPTION

The main body ECU detects the condition of the door courtesy switch assembly.

WIRING DIAGRAM

E124999E01

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (DOOR COURTESY SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and press the intelligent tester main switch ON.

  1. Select the items below in the Data List, and read the displays on the intelligent tester.

    Main body ECU:
    Item
    Measurement Item/Display (Range)
    Normal Condition
    Diagnostic Note
    D Dor Cty SW
    Driver's door courtesy switch signal/ON or OFF
    ON: Driver side door is open
    OFF: Driver side door is closed
    -
    P Dor Cty SW
    Passenger's door courtesy switch signal/ON or OFF
    ON: Front passenger side door is open
    OFF: Front passenger door is closed
    -
    RR Dor Cty SW
    Rear door courtesy switch signal/ON or OFF
    ON: Rear right passenger side door is open
    OFF: Rear right passenger side door is closed
    -
    RL Dor Cty SW
    Rear door courtesy switch signal/ON or OFF
    ON: Rear left passenger side door is open
    OFF: Rear left passenger side door is closed
    -
    Back Dor Cty SW
    Back door courtesy switch signal/ON or OFF
    ON: Back door is open
    OFF: Back door is closed
    -

    OK:
    Condition sign can be displayed.



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG


2. INSPECT COURTESY LIGHT SWITCH
E071371E07
  1. Remove the door courtesy light switch.

  1. Measure the resistance of the switch.

    Standard resistance:
    Front LH, Front RH, Rear LH, Rear RH, Back door 
    Tester Connection
    Condition
    Specified Condition
    1 - Body ground
    OFF
    10 kΩ or higher
    ON
    Below 1 Ω



NG
REPLACE DOOR COURTESY LIGHT SWITCH
OK


3. CHECK WIRE HARNESS (MAIN BODY ECU - COURTESY LIGHT SWITCH)
  1. Connect the courtesy light switch.

  1. Disconnect the IA, IC and ID instrument panel junction block connectors.

  1. Disconnect the E18 main body ECU connector.

B118226E02
  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    for LHD (front driver side)  
    Tester Connection
    Condition
    Specified Condition
    IA-21 (DCTY) - Body ground
    Front driver side door is opened
    Below 1 Ω
    Front driver side door is closed
    10 kΩ or higher
    for RHD (front driver side)  
    Tester Connection
    Condition
    Specified Condition
    IC-6 (DCTY) - Body ground
    Front driver side door is opened
    Below 1 Ω
    Front driver side door is closed
    10 kΩ or higher


    for LHD (front passenger side):
    Tester Connection
    Condition
    Specified Condition
    IC-14 (PCTY) - Body ground
    Front passenger side door is opened
    Below 1 Ω
    Front passenger side door is closed
    10 kΩ or higher
    for RHD (front passenger side) 
    Tester Connection
    Condition
    Specified Condition
    IA-24 (PCTY) - Body ground
    Front passenger side door is opened
    Below 1 Ω
    Front passenger side door is closed
    10 kΩ or higher

    for Rear door RH:
    Tester Connection
    Condition
    Specified Condition
    ID-7 (RRCY) - Body ground
    Rear door RH is opened
    Below 1 Ω
    Rear door RH is closed
    10 kΩ or higher

    for Rear door LH:
    Tester Connection
    Condition
    Specified Condition
    E18-8 (LCTY) - Body ground
    Rear door LH is opened
    Below 1 Ω
    Rear door LH is closed
    10 kΩ or higher

    for Back door:
    Tester Connection
    Condition
    Specified Condition
    IA-7 (BCTY) - Body ground
    Back door is opened
    Below 1 Ω
    Back door is closed
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU)


← Automatic Light Control Sensor Circuit (from Nov 2005)Door LOCK Position Circuit (from Nov 2005) →