Align the input shaft with the clutch disc and install the transaxle to the engine.
Install the 10 bolts.
Torque:
64 N*m{
653 kgf*cm
, 47 ft.*lbf
}
for bolt A
46 N*m{
469 kgf*cm
, 34 ft.*lbf
}
for bolt B
44 N*m{
449 kgf*cm
, 32 ft.*lbf
}
for bolt C
3.
INSTALL STIFFENER PLATE RH
Install the stiffener plate with the 4 bolts.
Torque:
46 N*m{
469 kgf*cm
, 34 ft.*lbf
}
4.
INSTALL STIFFENER PLATE LH
Install the stiffener plate with the 4 bolts.
Torque:
46 N*m{
469 kgf*cm
, 34 ft.*lbf
}
5.
INSTALL OIL PAN INSULATOR
Install the insulator with the 2 bolts.
Torque:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
6.
INSTALL REAR ENGINE MOUNTING BRACKET
Install the bracket with the 3 bolts.
Torque:
45 N*m{
459 kgf*cm
, 33 ft.*lbf
}
7.
INSTALL ENGINE MOUNTING BRACKET LH
Install the bracket with the 3 bolts.
Torque:
64 N*m{
653 kgf*cm
, 47 ft.*lbf
}
8.
INSTALL FRONT ENGINE MOUNTING BRACKET
Install the bracket with the 3 bolts.
Torque:
64 N*m{
653 kgf*cm
, 47 ft.*lbf
}
9.
INSTALL TRANSAXLE CONTROL CABLE ASSEMBLY
Connect the 2 cable ends with the 2 washers and 2 clips.
Install 2 new clips to the control cable bracket.
10.
INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY
1AZ-FE: Install the clutch release cylinder (Click here).
2AZ-FE: Install the clutch release cylinder (Click here).
11.
INSTALL BACK-UP LIGHT SWITCH ASSEMBLY
Install the back-up light switch and gasket to the manual transaxle case.
Torque:
40 N*m{
410 kgf*cm
, 30 ft.*lbf
}
Connect the back-up light switch connector.
12.
INSTALL TRANSFER ASSEMBLY
Install the transfer to the transaxle with the 6 nuts and 2 bolts.
Torque:
69 N*m{
700 kgf*cm
, 51 ft.*lbf
}
13.
INSTALL ENGINE ASSEMBLY WITH MANUAL TRANSAXLE
for 1AZ-FE: Install the engine with manual transaxle (Click here).
for 2AZ-FE: Install the engine with manual transaxle (Click here).
14.
ADD TRANSAXLE OIL
15.
INSPECT TRANSAXLE OIL
Stop the vehicle in a level place.
Remove the transaxle filler plug and gasket.
Check that the oil level is between 0 to 5 mm (0 to 0.20 in.) from the bottom lip of the filler plug opening. If the result is not as specified, add transaxle oil.
Oil grade:
GL-4
Viscosity:
SAE 75W
Standard capacity:
2.5 liters (2.6 US qts, 2.2 Imp. qts)
NOTICE:
Too much or too little oil will lead to transaxle problems.
After adjusting the oil level, drive the vehicle and check the oil level again.
Check for oil leakage if the oil level is low.
Install the transaxle filler plug and a new gasket.
Torque:
49 N*m{
500 kgf*cm
, 36 ft.*lbf
}
16.
ADD TRANSFER OIL
17.
INSPECT TRANSFER OIL
Remove the transfer case plug No. 2 (for filler) and gasket.
Check that the oil level is between 0 to 5.0 mm (0 to 0.20 in.) from the bottom lip of the case plug (for filler) hole. If the result is not as specified, add transfer oil.
Oil grade:
GL-5
Viscosity:
SAE 80W-90
Standard capacity:
0.45 liter (0.48 US qts, 0.40 Imp. qts)
NOTICE:
When adding oil, pour it slowly.
Too much or too little oil will lead to transfer problems.
When the oil level is too low, check for oil leakage.
Install a new gasket into the case plug (for filler) and then tighten the plug.