All Doors LOCK/UNLOCK Functions do not Operate Via Master Switch, Driver Side Door Key Cylinder
Circuit diagnosis · Vehicles built from Nov 2005
DESCRIPTION
The main body ECU receives switch signals from the door control switch on the power window regulator master switch, door control switch, driver side door key cylinder, passenger side door key cylinder and passenger side door lock switch, and activates the door lock motor on each door accordingly.WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DOOR LOCK) |
Select the Active Test, use the intelligent tester to generate a control command, and then check that the doors lock / unlock.
Main body ECU Item
Test Details
Diagnostic Note
DOOR LOCK
Operate door lock motor
LOCK / UNLOCK
-
- OK:
- Doors can lock / unlock.
|
|
||||
| NG | |
| 2. INSPECT FUSE (ECU - B) |
Remove the ECU-B fuse from the engine room No. 2 relay block.
Measure the resistance of the fuse.
- Standard resistance:
- Below 1 Ω
|
|
||||
| OK | |
| 3. CHECK WIRE HARNESS (ECU - BATTERY AND BODY GROUND) |


Disconnect the IB and IE junction block connectors.
Measure the voltage of the wire harness side connector.
- Standard voltage:
Tester Connection
Specified Condition
IB-30 (BECU) - Body ground
10 to 14 V
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
IE-17 (GND1) - Body ground
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 4. CHECK DRIVER SIDE DOOR LOCK / UNLOCK OPERATION |
Proceed to the next step according to the symptom listed in the table below.
Symptom
Proceed to
All doors cannot be locked / unlocked at once using door control switch on power window regulator master switch.
A
All doors cannot be locked / unlocked at once using door key cylinder on driver side.
B
All doors cannot be locked / unlocked at once using both door control switch on master switch and door key cylinder on driver side.
C
|
|
||||
|
|
||||
| A | |
| 5. READ VALUE USING INTELLIGENT TESTER (DOOR CONTROL SWITCH ON MASTER SWITCH) |
Use the Data List to check if the door control switch is functioning properly.
Main body ECU Item
Measurement / Display (Range)
Normal Condition
Diagnostic Note
Door Lock SW-Lock
Door manual lock switch signal / ON or OFF
ON: Door control switch on power window regulator master switch is pushed to lock position
OFF: Door control switch on power window regulator master switch is pushed
-
Door Lock SW-Unlock
Door manual unlock switch signal / ON or OFF
ON: Door control switch on power window regulator master switch is pushed to unlock position
OFF: Door control switch on power window regulator master switch is pushed
-
- OK:
- When the switch is operating, the intelligent tester should display as shown in the table.
|
|
||||
| NG | |
| 6. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY |
Remove the master switch.

Measure the resistance of the door control switch.
- Standard resistance:
- for LHD:
Tester Connection
Switch Condition
Specified Condition
2 (L) - 1 (E)
Lock
Below 80 Ω
2 (L) - 1 (E)
OFF
10 kΩ or higher
9 (UL) - 1 (E)
Unlock
Below 80 Ω
9 (UL) - 1 (E)
OFF
10 kΩ or higher
- for RHD:
Tester Connection
Switch Condition
Specified Condition
2 (L) - 9 (E)
Lock
Below 80 Ω
2 (L) - 9 (E)
OFF
10 kΩ or higher
8 (UL) - 9 (E)
Unlock
Below 80 Ω
8 (UL) - 9 (E)
OFF
10 kΩ or higher
|
|
||||
| OK | |
| 7. CHECK WIRE HARNESS (MASTER SWITCH - ECU AND BODY GROUND) |


for LHD:
Disconnect the H2 master switch connector.
Disconnect the IH junction block connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
H2-2 (L) - IH-4 (L1)
Below 1 Ω
H2-2 (L) - Body ground
10 kΩ or higher
IH-4 (L1) - Body ground
10 kΩ or higher
H2-9 (UL) - IH-5 (UL1)
Below 1 Ω
H2-9 (UL) - Body ground
10 kΩ or higher
IH-5 (UL1) - Body ground
10 kΩ or higher
H2-1 (E) - Body ground
Below 1 Ω
for RHD:
Disconnect the G8 master switch connector.
Disconnect the IH junction block connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
G8-2 (L) - IH-13 (L1)
Below 1 Ω
G8-2 (L) - Body ground
10 kΩ or higher
IH-13 (L1) - Body ground
10 kΩ or higher
G8-8 (UL) - IH-14 (UL1)
Below 1 Ω
G8-8 (UL) - Body ground
10 kΩ or higher
IH-14 (UL1) - Body ground
10 kΩ or higher
G8-9 (E) - Body ground
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 8. READ VALUE USING INTELLIGENT TESTER (DOOR KEY SWITCH) |
Use the Data List to check if the door key is functioning properly.
Main body ECU Item
Measurement / Display (Range)
Normal Condition
Diagnostic Note
Door Key SW-Lock
Door key linked lock switch signal / ON or OFF
ON: Driver side door key cylinder is turned to lock position
OFF: Driver side door key cylinder is not turned
-
Door Key SW-Unlock
Door key linked lock switch signal / ON or OFF
ON: Driver side door key cylinder is turned to unlock position
OFF: Driver side door key cylinder is not turned
-
- OK:
- When the door key is operating, the intelligent tester should display as shown in the table.
|
|
||||
| NG | |
| 9. INSPECT FRONT DOOR WITH MOTOR LOCK ASSEMBLY (DRIVER SIDE) |
for LHD:

Remove the front door lock.
Measure the resistance of the door lock and unlock switch.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
9 (L) -7 (E)
Lock
Below 1 Ω
9 (L) -7 (E)
OFF
10 kΩ or higher
10 (UL) - 7 (E)
Unlock
Below 1 Ω
10 (UL) - 7 (E)
OFF
10 kΩ or higher
for RHD (w/o Double Locking System):

Remove the front door lock.
Measure the resistance of the door key lock and unlock switch operation.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
5 (UL) -8 (E)
Lock
Below 1 Ω
5 (UL) -8 (E)
OFF
10 kΩ or higher
6 (L) - 8 (E)
Unlock
Below 1 Ω
6 (L) - 8 (E)
OFF
10 kΩ or higher
for RHD (w/ Double Locking System):

Remove the front door lock.
Measure the resistance of the door lock and unlock switch.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
5 (UL) -8 (E)
Lock
Below 1 Ω
5 (UL) -8 (E)
OFF
10 kΩ or higher
6 (L) - 8 (E)
Unlock
Below 1 Ω
6 (L) - 8 (E)
OFF
10 kΩ or higher
|
|
||||
| OK | |
| 10. CHECK WIRE HARNESS (MOTOR - ECU AND BODY GROUND) |


for LHD:
Disconnect the H5 door lock motor connector.
Disconnect the IH junction block connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
H5-9 (L) - IH-7 (L2)
Below 1 Ω
H5-9 (L) - Body ground
10 kΩ or higher
IH-7 (L2) - Body ground
10 kΩ or higher
H5-10 (UL) - IH-6 (UL2)
Below 1 Ω
H5-10 (UL) - Body ground
10 kΩ or higher
IH-6 (UL2) - Body ground
10 kΩ or higher
for RHD:
Disconnect the G5 door lock motor connector.
Disconnect the IH junction block connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
G5-6 (L) - IH-16 (L2)
Below 1 Ω
G5-6 (L) - Body ground
10 kΩ or higher
IH-16 (L2) - Body ground
10 kΩ or higher
G5-5 (UL) - IH-15 (UL2)
Below 1 Ω
G5-5 (UL) - Body ground
10 kΩ or higher
IH-15 (UL2) - Body ground
10 kΩ or higher
|
|
||||
| OK | ||
| ||
