DIAGNOSIS SYSTEM
Troubleshooting · Vehicles built Jan 2007 – Jul 2007
Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007
| DESCRIPTION |
- SST
- 09843-18040
| CHECK DLC3 |
![]() ![]() |
The vehicle's ECU uses the ISO 15765-4 communication protocol. The terminal arrangement of the DLC3 complies with SAE J1962 and matches the ISO 15765-4 format.
Verify the conditions listed in the table below.Symbols (Terminal No.)
Terminal Description
Condition
Specified Condition
SIL (7) - SG (5)
Bus + line
During transmission
Pulse generation
CG (4) - Body Ground
Chassis ground
Always
Below 1Ω
SG (5) - Body Ground
Signal ground
Always
Below 1Ω
BAT (16) - Body Ground
Battery positive
Always
11 to 14 V
CANH (6) - CANL (14)
HIGH-level CAN bus line
Ignition switch off *
54 to 69 Ω
CANH (6) - BAT (16)
HIGH-level CAN bus line
Ignition switch off *
1 MΩ or higher
CANH (6) - CG (4)
HIGH-level CAN bus line
Ignition switch off *
200 Ω or higher
CANL (14) - BAT (16)
LOW-level CAN bus line
Ignition switch off *
1 MΩ or higher
CANL (14) -CG (4)
LOW-level CAN bus line
Ignition switch off *
200 Ω or higher
- NOTICE:
- *: Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, other switches or the doors.
- HINT:
- Connect the cable of the intelligent tester to the DLC3, turn the ignition switch on (IG) and attempt to use the tester. If the display indicates that a communication error has occurred, there is a problem either with the vehicle or with the tester.
- If communication is normal when the tester is connected to another vehicle, inspect the DLC3 of the original vehicle.
- If communication is still not possible when the tester is connected to another vehicle, the problem may be in the tester itself. Consult the Service Department listed in the tester's instruction manual.
| FUNCTION OF 4WD INDICATOR LIGHT |
The 4WD indicator light in the combination meter (multi-information display) warns the driver of abnormal or poor condition of the 4WD control system.
w/o Multi-information display:
If the 4WD control ECU detects a malfunction, the 4WD indicator lights comes on in accordance with the trouble area to warn the driver.w/ Multi-information display:
If the 4WD control ECU detects a malfunction, the check master caution indicator comes on (*1) and the multi-information display displays warning messages (*2) in accordance with the trouble area to warn the driver.- HINT:
- Check that the master caution indicator comes on for approximately 4 seconds. (*1)


| CHECK 4WD INDICATOR LIGHT (w/ Multi-information Display) |
![]() ![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3 (to enter diagnostic mode).
- SST
- 09843-18040
Turn the ignition switch on (IG).
"DIAG" is displayed on the multi-information display, and the 4WD control ECU checks the system for malfunctions.



- If the 4WD control system is normal, "4WD FF" will be displayed on the multi-information display.
- If the 4WD control system is not normal, " 4WD XX (DTC)" will be displayed on the multi-information display.
-
Although the test mode is not set for the 4WD control system, the message shown in the illustration will be displayed on the multi-information display when the test mode is activated for checking the VSC, etc.

- HINT:
- Test mode DTCs will not be stored because the test mode is not set.
- Test mode DTCs will not be stored because the test mode is not set.
- On the multi-information display, VSC, TIRE PRESSURE and 4WD are displayed in order.
- On the multi-information display, VSC, TIRE PRESSURE and 4WD are displayed in order.
- If the systems above are not displayed on the multi-information display, there may be a malfunction in "TC and CG Terminal Circuit".
- If the systems above are not displayed on the multi-information display, there may be a malfunction in "TC and CG Terminal Circuit".
- If the 4WD indicator light check result is not normal, proceed to troubleshooting for the 4WD indicator light circuit.
- If the 4WD indicator light check result is not normal, proceed to troubleshooting for the 4WD indicator light circuit.
Trouble Area
See procedure
4WD indicator light (Remains on)
Click here
4WD indicator light (Does not come on)
Click here
- If the 4WD control system is normal, "4WD FF" will be displayed on the multi-information display.

