2005-2008 RAV4 · Service Manual DRIVE LINE

DATA LIST / ACTIVE TEST

System information · Vehicles built from Nov 2005


READ DATA LIST

HINT:
Using the intelligent tester's Data List allows switch, sensor and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch on (IG).

  3. Read the Data List according to the display on the tester.

4WD control ECU 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
4WD warning lamp
4WD indicator light /OFF or ON
OFF: 4WD indicator light off
ON: 4WD indicator light on
-
4WD Lock lamp
4WD lock light /OFF or ON
OFF: 4WD lock light off
ON: 4WD lock light on
-
Stop lamp SW
Stop light switch /OFF or ON
OFF: Brake pedal released
ON: Brake pedal depressed
-
Steering angle
Steering angle value /
Min.: -3276.8 deg
Max.: 3276.7 deg
Min.: -3276.8 deg
Max.: 3276.7 deg
-
FR wheel SPD
FR wheel speed /
Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202.8 mph)
Actual wheel speed
Almost no difference from the speedometer
FL wheel SPD
FL wheel speed /
Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202.8 mph)
Actual wheel speed
Almost no difference from the speedometer
RR wheel SPD
RR wheel speed /
Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202.8 mph)
Actual wheel speed
Almost no difference from the speedometer
RL wheel SPD
RL wheel speed /
Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202.8 mph)
Actual wheel speed
Almost no difference from the speedometer
Ambi temp
Ambient temperature /
Min.: -128 °C (198.4 °F)
Max.: 127 °C (260.6 °F)
Min.: -128 (198.4 °F)
Max.: 127 (260.6 °F)
-
Coolant temp
Engine coolant temperature /
Min.: 0 °C (32 °F)
Max.: 127.5 °C (261.5 °F)
Min.: 0 °C (32 °F)
Max.: 127.5 °C (261.5 °F)
-
Lock SW
4WD lock switch / OFF or ON
OFF: 4WD lock switch off
ON: 4WD lock switch on
-
SLC CUR
SLC solenoid (4WD linear solenoid) current /
Min.: 0 A
Max.: 3 A
Min.: 0 A
Max.: 3 A
-

PERFORM ACTIVE TEST

HINT:
Performing the intelligent tester's Active Test allows switch and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time. The Data List can be displayed during the Active Test.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the engine switch on (IG).

  3. Perform the Active Test according to the display on the tester.

    4WD control ECU 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    4WD warn light
    4WD indicator light
    ON: 4WD indicator light on
    OFF: 4WD indicator light off
    ON / OFF
    Observe combination meter
    Lock light
    4WD lock light
    OFF: 4WD lock switch off
    ON: 4WD lock switch on
    ON / OFF
    Observe combination meter
    Skid control ECU 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Slip Indi light (w/ VSC)
    SLIP indicator light
    ON: SLIP indicator light on
    OFF: SLIP indicator light off
    ON / OFF
    Observe combination meter

← FAIL-SAFE CHART (from Nov 2005)DIAGNOSTIC TROUBLE CODE CHART (Nov 2005 – Dec 2006) →