Turn Signal Light Circuit
Circuit diagnosis · Vehicles built from Aug 2008
Versions by build date: Nov 2005 – Jul 2008 from Aug 2008
DESCRIPTION
The turn signal flasher relay (marking for LHD: turn signal flasher) turns on when it receives signals from the headlight dimmer switch integrated with the turn signal switch, causing the turn signal lights to flash.WIRING DIAGRAM




INSPECTION PROCEDURE
| 1. INSPECT VEHICLE CONDITION |
Check the vehicle condition.
Result Result
Proceed to
RHD
A
LHD
B
|
|
||||
| A | |
| 2. CHECK OPERATION OF TURN SIGNAL LIGHT |
When the turn signal light switch is operated, check that the appropriate turn signal light flashes.
*1: w/o Door Mirror Turn Signal Light*2: w/ Door Mirror Turn Signal LightResult Condition
Proceed to
All lights do not flash
A
Front turn signal light (LH or RH) does not flash
B
Door mirror turn signal light (LH or RH) does not flash*2
C
Rear turn signal light (LH or RH) does not flash
D
Front side turn signal light (LH or RH) does not flash*1
E
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | |
| 3. INSPECT FUSE (ECU-IG2, HAZ) |
Remove the ECU-IG2 fuse from the instrument panel junction block.
Remove the HAZ fuse from the engine room No. 1 relay block.
Measure the resistance of the fuse.
- Standard resistance:
- Below 1 Ω
|
|
||||
| OK | |
| 4. CHECK WIRE HARNESS (BATTERY - TURN SIGNAL FLASHER RELAY) |
![]() ![]() |
Disconnect the E81 turn signal flasher relay connector.
Measure the voltage of the wire harness side connector.
- Standard voltage:
Tester Connection
Condition
Specified Condition
E81-1 (IG) - Body ground
Ignition switch on (IG)
11 to 14 V
E81-4 (B) - Body ground
Always
11 to 14 V
|
|
||||
| OK | |
| 5. INSPECT HEADLIGHT DIMMER SWITCH |
![]() ![]() |
Remove the headlight dimmer switch.
Measure the resistance of the switch.
- Standard resistance:
Tester Connection
Condition
Specified Condition
16 (TR) - 19 (EL)
Right turn
Below 1 Ω
18 (TL) - 19 (EL)
Left turn
Below 1 Ω
16 (TR) - 19 (EL)
Neutral
10 kΩ or higher
18 (TL) - 19 (EL)
Neutral
10 kΩ or higher
|
|
||||
| OK | |
| 6. CHECK WIRE HARNESS (TURN SIGNAL FLASHER RELAY - DIMMER SWITCH AND BODY GROUND) |
![]() ![]() |
Disconnect the E15 headlight dimmer switch connector.
Disconnect the E81 turn signal flasher relay connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
E15-16 (TR) - E81-6 (ER)
Below 1 Ω
E15-16 (TR) or E81-6 (ER) - Body ground
10 kΩ or higher
E15-18 (TL) - E81-5 (EL)
Below 1 Ω
E15-18 (TL) or - E81-5 (EL) - Body ground
10 kΩ or higher
E15-19 (EL) - Body ground
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 7. INSPECT BULB (FRONT TURN SIGNAL BULB) |
![]() ![]() |
Remove the front turn signal light bulb.
Connect the positive (+) lead from the battery to terminal 2 and the negative (-) lead to terminal 1, then check that the bulb illuminates.
- OK:
- Bulb illuminates.
|
|
||||
| OK | |
| 8. CHECK WIRE HARNESS (TURN SIGNAL FLASHER RELAY - FRONT TURN SIGNAL LIGHT) |
![]() ![]() |
Disconnect the A16 (for LH) and A37 (for RH) front turn signal light connectors.
Disconnect the E81 turn signal flasher relay connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
for LH side: Tester Connection
Specified Condition
E81-3 (LL) - A16-2
Below 1 Ω
E81-3 (LL) or A16-2 - Body ground
10 kΩ or higher
for RH side: Tester Connection
Specified Condition
E81-2 (LR) - A37-2
Below 1 Ω
E81-2 (LR) or A37-2 - Body ground
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 9. INSPECT DOOR MIRROR TURN SIGNAL LIGHT |
Remove the door mirror turn signal light.

Connect the positive (+) lead from the battery to terminal 1 and the negative (-) lead to terminal 2, and then check that the light comes on.
- OK:
- Light comes on.
|
|
||||
| OK | |
| 10. CHECK WIRE HARNESS (OUTER REAR VIEW MIRROR - TURN SIGNAL FLASHER RELAY) |
![]() ![]() |
Disconnect the H11 (for LH) and G10 (for RH) outer rear view mirror connectors.
Disconnect the E81 turn signal flasher relay connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
for LH side: Tester Connection
Specified Condition
E81-3 (LL) - H11-10
Below 1 Ω
E81-3 (LL) or H11-10 - Body ground
10 kΩ or higher
H11-11 - Body ground
Below 1 Ω
for RH side: Tester Connection
Specified Condition
E81-2 (LR) - G10-10
Below 1 Ω
E81-2 (LR) or G10-10 - Body ground
10 kΩ or higher
G10-11 - Body ground
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 11. INSPECT REAR COMBINATION LIGHT |
![]() ![]() |
Remove the rear combination light.
Connect the positive (+) lead from the battery to terminal 5 and the negative (-) lead to terminal 1, then check that the bulb illuminates.
- HINT:
- Be sure to check the bulb first.
- OK:
- Bulb illuminates.
|
|
||||
| OK | |
| 12. CHECK WIRE HARNESS (TURN SIGNAL FLASHER RELAY - REAR COMBINATION LIGHT) |
![]() ![]() |
Disconnect the K13 (for RH) and K15 (for LH) rear combination light connectors.
Disconnect the E81 turn signal flasher relay connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
for LH side: Tester Connection
Specified Condition
E81-3 (LL) - K15-5
Below 1 Ω
E81-3 (LL) or K15-5 - Body ground
10 kΩ or higher
for RH side: Tester Connection
Specified Condition
E81-2 (LR) - K13-5
Below 1 Ω
E81-2 (LR) or K13-5 - Body ground
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 13. CHECK OPERATION OF TURN SIGNAL LIGHT |
When the turn signal light switch is operated, check that the appropriate turn signal light flashes.
*1: w/o Door Mirror Turn Signal Light*2: w/ Door Mirror Turn Signal LightResult Condition
Proceed to
All lights do not flash
A
Front turn signal light (LH or RH) does not flash
B
Front side turn signal light (LH or RH) does not flash*1
C
Rear turn signal light (LH or RH) does not flash
D
Door mirror turn signal light (LH or RH) does not flash*2
E
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | |
| 14. INSPECT FUSE (ECU-IG2, HAZ) |
Remove the ECU-IG2 fuse from the instrument panel junction block.
Remove the HAZ fuse from the engine room No. 1 relay block.
Measure the resistance of the fuse.
- Standard resistance:
- Below 1 Ω
|
|
||||
| OK | |
| 15. CHECK WIRE HARNESS (TURN SIGNAL FLASHER RELAY - BATTERY) |
![]() ![]() |
Remove the turn signal flasher relay from the instrument panel junction block.
Measure the voltage of the relay block.
- Standard voltage:
Tester Connection
Condition
Specified Condition
Turn signal flasher relay terminal 1 (IG) - Body ground
Ignition switch on (IG)
11 to 14 V
Turn signal flasher relay terminal 4 (+B) - Body ground
Always
11 to 14 V
|
|
||||
| OK | |
| 16. INSPECT HEADLIGHT DIMMER SWITCH |
![]() ![]() |
Remove the headlight dimmer switch.
Measure the resistance of the switch.
- Standard resistance:
Tester Connection
Condition
Specified Condition
13 (TR) - 12 (EL)
Right turn
Below 1 Ω
15 (TL) - 12 (EL)
Left turn
Below 1 Ω
13 (TR) - 12 (EL)
Neutral
10 kΩ or higher
15 (TL) - 12 (EL)
Neutral
10 kΩ or higher
|
|
||||
| OK | |
| 17. CHECK WIRE HARNESS (TURN SIGNAL FLASHER RELAY - DIMMER SWITCH) |


Remove the turn signal flasher relay from the instrument panel junction block.
Disconnect the E15 headlight dimmer switch connector.
Measure the resistance of the wire harness side connectors and junction block.
Tester Connection
Specified Condition
Turn signal flasher relay terminal 5 (EL) - E15-15 (TL)
Below 1 Ω
Turn signal flasher relay terminal 5 (EL) or E15-15 (TL) - Body ground
10 kΩ or higher
Turn signal flasher relay terminal 6 (ER) - E15-13 (TR)
Below 1 Ω
Turn signal flasher relay terminal 6 (ER) or E15-13 (TR) - Body ground
10 kΩ or higher
E15-12 (EL) - Body ground
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 18. INSPECT FRONT TURN SIGNAL LIGHT BULB |
![]() ![]() |
Remove the front turn signal light bulb.
Connect the positive (+) lead from the battery to terminal 2 and the negative (-) lead to terminal 1, then check that the bulb illuminates.
- OK:
- Bulb illuminates.
|
|
||||
| OK | |
| 19. CHECK WIRE HARNESS (INSTRUMENT PANEL JUNCTION BLOCK - FRONT TURN SIGNAL LIGHT) |
![]() ![]() |
Remove the turn signal flasher relay.
Disconnect the A16 (for LH) and A37 (for RH) front turn signal light connectors.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
for LH side: Tester Connection
Specified Condition
Junction block turn signal flasher relay terminal 3 (LL) - A16-2
Below 1 Ω
Junction block turn signal flasher relay terminal 3 (LL) or A16-2 - Body ground
10 kΩ or higher
for RH side: Tester Connection
Specified Condition
Junction block turn signal flasher relay terminal 2 (LR) - A37-2
Below 1 Ω
Junction block turn signal flasher relay terminal 2 (LR) or A37-2 - Body ground
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 20. INSPECT FRONT SIDE TURN SIGNAL LIGHT BULB |
![]() ![]() |
Remove the front side turn signal light bulb.
Connect the positive (+) lead from the battery to terminal 2 and the negative (-) lead to terminal 1, then check that the bulb illuminates.
- OK:
- Bulb illuminates.
|
|
||||
| OK | |
| 21. CHECK WIRE HARNESS (JUNCTION BLOCK - FRONT SIDE TURN SIGNAL LIGHT) |
![]() ![]() |
Disconnect the A14 (for LH) and A39 (for RH) front side turn signal light connectors.
Remove the turn signal flasher relay.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
for LH side: Tester Connection
Specified Condition
Junction block turn signal flasher relay terminal 3 (LL) - A14-2
Below 1 Ω
Junction block turn signal flasher relay terminal 3 (LL) or A14-2 - Body ground
10 kΩ or higher
for RH side: Tester Connection
Specified Condition
Junction block turn signal flasher relay terminal 2 (LR) - A39-2
Below 1 Ω
Junction block turn signal flasher relay terminal 2 (LR) or A39-2 - Body ground
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 22. INSPECT REAR COMBINATION LIGHT |
![]() ![]() |
Remove the rear combination light.
Connect the positive (+) lead from the battery to terminal 5 and the negative (-) lead to terminal 1, then check that the bulb illuminates.
- HINT:
- Be sure to check the bulb first.
- OK:
- Bulb illuminates.
|
|
||||
| OK | |
| 23. CHECK WIRE HARNESS (INSTRUMENT PANEL JUNCTION BLOCK - REAR COMBINATION LIGHT) |
![]() ![]() |
Disconnect the K13 (for RH) and K15 (for LH) rear combination light connectors.
Remove the turn signal flasher relay.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
for LH side: Tester Connection
Specified Condition
Junction block turn signal flasher relay terminal 3 (LL) - K15-5
Below 1 Ω
Junction block turn signal flasher relay terminal 3 (LL) or K15-5 - Body ground
10 kΩ or higher
for RH side: Tester Connection
Specified Condition
Junction block turn signal flasher relay terminal 2 (LR) - K13-5
Below 1 Ω
Junction block turn signal flasher relay terminal 2 (LR) or K13-5 - Body ground
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 24. INSPECT DOOR MIRROR TURN SIGNAL LIGHT |
Remove the door mirror turn signal light.

Connect the positive (+) lead from the battery to terminal 1 and the negative (-) lead to terminal 2, and then check that the light comes on.
- OK:
- Light comes on.
|
|
||||
| OK | |
| 25. CHECK WIRE HARNESS (INSTRUMENT PANEL JUNCTION BLOCK - OUTER REAR VIEW MIRROR) |
![]() ![]() |
Disconnect the H11 (for LH) and G10 (for RH) outer rear view mirror connectors.
Remove the turn signal flasher relay.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
for LH side: Tester Connection
Specified Condition
Junction block turn signal flasher relay terminal 3 (LL) - H11-10
Below 1 Ω
Junction block turn signal flasher relay terminal 3 (LL) or H11-10 - Body ground
10 kΩ or higher
H11-11 - Body ground
Below 1 Ω
for RH side: Tester Connection
Specified Condition
Junction block turn signal flasher relay terminal 2 (LR) - G10-10
Below 1 Ω
Junction block turn signal flasher relay terminal 2 (LR) or G10-10 - Body ground
10 kΩ or higher
G10-11 - Body ground
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 26. INSPECT FRONT SIDE TURN SIGNAL LIGHT BULB |
![]() ![]() |
Remove the front side turn signal light bulb.
Connect the positive (+) lead from the battery to terminal 2 and the negative (-) lead to terminal 1, then check that the bulb illuminates.
- OK:
- Bulb illuminates.
|
|
||||
| OK | |
| 27. CHECK WIRE HARNESS (TURN SIGNAL FLASHER RELAY - FRONT SIDE TURN SIGNAL LIGHT) |
![]() ![]() |
Disconnect the A14 (for LH) and A39 (for RH) front side turn signal light connectors.
Disconnect the E81 turn signal flasher relay connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
for LH side: Tester Connection
Specified Condition
E81-3 (LL) - A14-2
Below 1 Ω
E81-3 (LL) or A14-2 - Body ground
10 kΩ or higher
for RH side: Tester Connection
Specified Condition
E81-2 (LR) - A39-2
Below 1 Ω
E81-2 (LR) or A39-2 - Body ground
10 kΩ or higher
|
|
||||
| OK | ||
| ||

















