2005-2008 RAV4 · Service Manual BODY ELECTRICAL

Turn Signal Light Circuit

Circuit diagnosis · Vehicles built Nov 2005 – Jul 2008

Versions by build date: Nov 2005 – Jul 2008 from Aug 2008

DESCRIPTION

The turn signal flasher relay (marking for LHD: turn signal flasher) turns on when it receives signals from the headlight dimmer switch integrated with the turn signal switch, causing the turn signal lights to flash.

WIRING DIAGRAM

B128015E01
B128013E01

INSPECTION PROCEDURE


1. INSPECT VEHICLE CONDITION
  1. Check the vehicle condition.

    Result 
    Result
    Proceed to
    RHD
    A
    LHD
    B



B
Go to step 13
A


2. CHECK OPERATION OF TURN SIGNAL LIGHT
  1. When the turn signal light switch is operated, check that the appropriate turn signal light flashes.

    Result 
    Condition
    Proceed to
    All lights do not flash
    A
    Front turn signal light (LH or RH) does not flash
    B
    Front side turn signal light (LH or RH) does not flash
    C
    Rear turn signal light (LH or RH) does not flash
    D



B
Go to step 7

C
Go to step 9

D
Go to step 11
A


3. INSPECT FUSE (ECU-IG2, HAZ)
  1. Remove the ECU-IG2 fuse from the instrument panel junction block.

  1. Remove the HAZ fuse from the engine room No. 1 relay block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


4. CHECK WIRE HARNESS (BATTERY - TURN SIGNAL FLASHER RELAY)
E120966E04
  1. Disconnect the E81 turn signal flasher relay connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E81-1 (IG) - Body ground
    Ignition switch on (IG)
    10 to 14 V
    E81-4 (B) - Body ground
    Always
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


5. INSPECT HEADLIGHT DIMMER SWITCH
B128006E07
  1. Remove the headlight dimmer switch.

  1. Measure the resistance of the switch.

    Standard resistance:
    for LH side 
    Tester Connection
    Condition
    Specified Condition
    13 (TR) - 12 (EL)
    Right turn
    Below 1 Ω
    15 (TL) - 12 (EL)
    Left turn
    Below 1 Ω
    13 (TR) - 12 (EL)
    Neutral
    10 kΩ or higher
    15 (TL) - 12 (EL)
    Neutral
    10 kΩ or higher
    for RH side 
    Tester Connection
    Condition
    Specified Condition
    16 (TR) - 19 (EL)
    Right turn
    Below 1 Ω
    18 (TL) - 19 (EL)
    Left turn
    Below 1 Ω
    16 (TR) - 19 (EL)
    Neutral
    10 kΩ or higher
    18 (TL) - 19 (EL)
    Neutral
    10 kΩ or higher



NG
REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY
OK


6. CHECK WIRE HARNESS (TURN SIGNAL FLASHER RELAY - DIMMER SWITCH AND BODY GROUND)
B128016E02
  1. Disconnect the E15 headlight dimmer switch connector.

  1. Disconnect the E81 turn signal flasher relay connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    for LH side 
    Tester Connection
    Specified Condition
    E15-13 (TR) - E81-6 (ER)
    Below 1 Ω
    E15-13 (TR) or E81-6 (ER) - Body ground
    10 kΩ or higher
    E15-15 (TL) - E81-5 (EL)
    Below 1 Ω
    E15-15 (TL) or - E81-5 (EL) - Body ground
    10 kΩ or higher
    E15-12 (EL) - Body ground
    Below 1 Ω
    for RH side 
    Tester Connection
    Specified Condition
    E15-16 (TR) - E81-6 (ER)
    Below 1 Ω
    E15-16 (TR) or E81-6 (ER) - Body ground
    10 kΩ or higher
    E15-18 (TL) - E81-5 (EL)
    Below 1 Ω
    E15-18 (TL) or - E81-5 (EL) - Body ground
    10 kΩ or higher
    E15-19 (EL) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE TURN SIGNAL FLASHER RELAY

7. INSPECT BULB (FRONT TURN SIGNAL BULB)
  1. Remove the front turn signal light bulb.

  1. Connect the positive (+) lead from the battery to terminal 2 and the negative (-) lead to terminal 1, then check that the bulb illuminates.

    OK:
    Bulb illuminates.



NG
REPLACE FRONT TURN SIGNAL LIGHT BULB
OK


8. CHECK WIRE HARNESS (INSTRUMENT PANEL JUNCTION BLOCK - FRONT TURN SIGNAL LIGHT)
B128017E02
  1. Disconnect the A16 and A37 front turn signal light connectors.

  1. Disconnect the IB instrument panel junction block connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    IB-14 (LL) - A16-2
    Below 1 Ω
    IB-14 (LL) or A16-2 - Body ground
    10 kΩ or higher
    IB-31 (LR) - A37-2
    Below 1 Ω
    IB-31 (LR) or A37-2 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPAIR OR REPLACE HARNESS AND CONNECTOR (FRONT TURN SIGNAL LIGHT - BODY GROUND)

9. INSPECT FRONT TURN SIGNAL LIGHT BULB (FRONT SIDE TURN SIGNAL LIGHT BULB)
  1. Remove the front side turn signal light bulb.

  1. Connect the positive (+) lead from the battery to terminal 2 and the negative (-) lead to terminal 1, then check that the bulb illuminates.

    OK:
    Bulb illuminates.



NG
REPLACE FRONT SIDE TURN SIGNAL LIGHT BULB
OK


10. CHECK WIRE HARNESS (JUNCTION BLOCK - FRONT SIDE TURN SIGNAL LIGHT BULB)
E120451E04
  1. Disconnect the A14 and A39 front side turn signal light connectors.

  1. Disconnect the IB instrument panel junction block connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    IB-14 (LL) - A14-2
    Below 1 Ω
    IB-14 (LL) or A14-2 - Body ground
    10 kΩ or higher
    IB-31 (LR) - A39-2
    Below 1 Ω
    IB-31 (LR) or A39-2 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPAIR OR REPLACE HARNESS AND CONNECTOR (SIDE TURN SIGNAL LIGHT - BODY GROUND)

11. INSPECT BULB (REAR TURN SIGNAL LIGHT BULB)
B118217E04
  1. Remove the rear combination light.

  1. Connect the positive (+) lead from the battery to terminal 5 and the negative (-) lead to terminal 1, then check that the bulb illuminates.

    OK:
    Bulb illuminates.



NG
REPLACE REAR TURN SIGNAL LIGHT BULB
OK


12. CHECK WIRE HARNESS (INSTRUMENT PANEL JUNCTION BLOCK - REAR TURN SIGNAL LIGHT)
E125284E06
  1. Disconnect the K13 and K15 rear combination light connectors.

  1. Disconnect the IA instrument panel junction block connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    IA-27 (LL) - K15-5
    Below 1 Ω
    IA-27 (LL) or K15-5 - Body ground
    10 kΩ or higher
    IA-28 (LR) - K13-5
    Below 1 Ω
    IA-28 (LR) or K13-5 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPAIR OR REPLACE HARNESS AND CONNECTOR (REAR COMBINATION LIGHT - BODY GROUND)

13. CHECK OPERATION OF TURN SIGNAL LIGHT
  1. When the turn signal light switch is operated, check that the appropriate turn signal light flashes.

    Result 
    Condition
    Proceed to
    All lights do not flash
    A
    Front turn signal light (LH or RH) does not flash
    B
    Front side turn signal light (LH or RH) does not flash
    C
    Rear turn signal light (LH or RH) does not flash
    D



B
Go to step 18

C
Go to step 20

D
Go to step 22
A


14. INSPECT FUSE (ECU-IG2, HAZ)
  1. Remove the ECU-IG2 fuse from the instrument panel junction block.

  1. Remove the HAZ fuse from the engine room No. 1 relay block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


15. CHECK WIRE HARNESS (TURN SIGNAL FLASHER RELAY - BATTERY)
B128069E01
  1. Remove the turn signal flasher relay from the instrument panel junction block.

  1. Measure the voltage of the relay block.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    Turn signal flasher relay terminal 1 (IG) - Body ground
    Ignition switch on (IG)
    10 to 14 V
    Turn signal flasher relay terminal 4 (+B) - Body ground
    Always
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


16. INSPECT HEADLIGHT DIMMER SWITCH
E068152E08
  1. Remove the headlight dimmer switch.

  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    13 (TR) - 12 (EL)
    Right turn
    Below 1 Ω
    15 (TL) - 12 (EL)
    Left turn
    Below 1 Ω
    13 (TR) - 12 (EL)
    Neutral
    10 kΩ or higher
    15 (TL) - 12 (EL)
    Neutral
    10 kΩ or higher



NG
REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY
OK


17. CHECK WIRE HARNESS (TURN SIGNAL FLASHER RELAY - DIMMER SWITCH)
B128070E01
  1. Remove the turn signal flasher relay from the instrument panel junction block.

  1. Disconnect the E15 headlight dimmer switch connector.

  1. Measure the resistance of the wire harness side connectors and junction block.

    Tester Connection
    Specified Condition
    Turn signal flasher relay terminal 5 (EL) - E15-15 (TL)
    Below 1 Ω
    Turn signal flasher relay terminal 5 (EL) or E15-15 (TL) - Body ground
    10 kΩ or higher
    Turn signal flasher relay terminal 6 (ER) - E15-13 (TR)
    Below 1 Ω
    Turn signal flasher relay terminal 6 (ER) or E15-13 (TR) - Body ground
    10 kΩ or higher
    E15-12 (EL) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE TURN SIGNAL FLASHER RELAY

18. INSPECT FRONT TURN SIGNAL LIGHT BULB
  1. Remove the front turn signal light bulb.

  1. Connect the positive (+) lead from the battery to terminal 2 and the negative (-) lead to terminal 1, then check that the bulb illuminates.

    OK:
    Bulb illuminates.



NG
REPLACE FRONT TURN SIGNAL LIGHT BULB
OK


19. CHECK WIRE HARNESS (INSTRUMENT PANEL JUNCTION BLOCK - FRONT TURN SIGNAL LIGHT)
B128017E02
  1. Disconnect the IB instrument panel junction block connector.

  1. Disconnect the A16 and A37 front turn signal light connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    IB-14 (LL) - A16-2
    Below 1 Ω
    IB-14 (LL) or A16-2 - Body ground
    10 kΩ or higher
    IB-31 (LR) - A37-2
    Below 1 Ω
    IB-31 (LR) or A37-2 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPAIR OR REPLACE HARNESS AND CONNECTOR (FRONT TURN SIGNAL LIGHT - BODY GROUND)

20. CHECK FRONT SIDE TURN SIGNAL LIGHT BULB
  1. Remove the front side turn signal light bulb.

  1. Connect the positive (+) lead from the battery to terminal 2 and the negative (-) lead to terminal 1, then check that the bulb illuminates.

    OK:
    Bulb illuminates.



NG
REPLACE FRONT SIDE TURN SIGNAL LIGHT BULB
OK


21. CHECK WIRE HARNESS (JUNCTION BLOCK - FRONT SIDE TURN SIGNAL LIGHT)
E120451E04
  1. Disconnect the A14 and A39 front side turn signal light connectors.

  1. Disconnect the IB instrument panel junction block connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    IB-14 (LL) - A14-2
    Below 1 Ω
    IB-14 (LL) or A14-2 - Body ground
    10 kΩ or higher
    IB-31 (LR) - A39-2
    Below 1 Ω
    IB-31 (LR) or A39-2 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPAIR OR REPLACE HARNESS AND CONNECTOR (SIDE TURN SIGNAL LIGHT - BODY GROUND)

22. INSPECT REAR TURN SIGNAL LIGHT BULB
B118217E07
  1. Remove the rear combination light.

  1. Connect the positive (+) lead from the battery to terminal 5 and the negative (-) lead to terminal 1, then check that the bulb illuminates.

    OK:
    Bulb illuminates.



NG
REPLACE REAR TURN SIGNAL LIGHT BULB
OK


23. CHECK WIRE HARNESS (INSTRUMENT PANEL JUNCTION BLOCK - REAR TURN SIGNAL LIGHT)
E125284E06
  1. Disconnect the K13 and K15 rear combination light connectors.

  1. Disconnect the IA instrument panel junction block connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    IA-27 (LL) - K15-5
    Below 1 Ω
    IA-27 (LL) or K15-5 - Body ground
    10 kΩ or higher
    IA-28 (LR) - K13-5
    Below 1 Ω
    IA-28 (LR) or K13-5 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPAIR OR REPLACE HARNESS AND CONNECTOR (REAR COMBINATION LIGHT - BODY GROUND)


← Rear Fog Light Circuit (from Nov 2005)Turn Signal Light Circuit (from Aug 2008) →