2005-2008 RAV4 · Service Manual TRANSMISSION

REASSEMBLY

Removal / installation · Vehicles built from Nov 2005


1. INSTALL SYNCHRONIZER PULL RING

C069514E01
  1. Install the No. 5 synchronizer ring middle, No. 5 synchronizer ring outer and synchronizer pull ring to the No. 5 synchronizer ring inner. Using a screwdriver, fix them in place with the synchronizer pull ring snap ring.


2. INSTALL NO. 5 SYNCHRONIZER RING MIDDLE

C069510E01
  1. Check that the No. 5 synchronizer ring middle rotates smoothly.

  1. C069511E01
    Check that the No. 5 synchronizer ring middle does not rotate while being pushed against the No. 3 clutch hub.


3. INSTALL NO. 3 SYNCHROMESH SHIFTING KEY SPRING

C069515E01
  1. Install the No. 3 synchromesh shifting key spring to the No. 3 transaxle clutch hub.

    NOTICE:
    Align the projection of the shifting key spring with the hole of the No. 3 clutch hub and install it.

  1. Install the synchronizer ring set and No. 3 synchromesh shifting key spring to the No. 3 transaxle clutch hub.

    NOTICE:
    1. Engage the shifting key spring claw to the center of the teeth of the synchronizer ring.
    2. Align the projection of the shifting key spring with the hole of the No. 3 clutch hub and install it.


4. INSTALL FRONT TRANSAXLE CASE COVER OIL SEAL

C087990E01
  1. Using SST and a hammer, tap in a new front transaxle case cover oil seal.

    SST
    09316-20011  
    09950-60020   (09951-00910)
    09950-70010   (09951-07150)

    Standard depth:
    -0.5 to 0.5 mm (-0.020 to 0.020 in.)

  1. Coat the lip of the oil seal with MP grease.


5. INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

C087991E01
  1. Using SST and a hammer, tap in the front tapered roller bearing (outer race) to the front differential case.

    SST
    09950-60020   (09951-00910)
    09950-70010   (09951-07100, 09951-07150)

  1. C070823E01
    Using SST and a press, press in the front tapered roller bearing (inner race) to the front differential case.
    SST
    09950-70010   (09951-07100, 09951-07150)
    09608-10010  


6. INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

C087992E01
  1. Install the rear shim.

  1. Using SST and a hammer, tap in the rear tapered roller bearing (outer race).

    SST
    09950-60020   (09951-00890)
    09950-70010   (09951-07100)

  1. C090204E03
    Using SST and a press, press in the rear tapered roller bearing (inner race).
    SST
    09631-12090  
    09950-60010   (09951-00600)
    09950-70010   (09951-07100)


7. INSTALL TRANSAXLE CASE OIL SEAL

C087993E03
  1. Using SST and a hammer, tap in a new oil seal to the transaxle case.

    SST
    09608-32010  
    09950-70010   (09951-07150)

    Standard depth:
    3.0 to 4.0 mm (0.118 to 0.158 in.)

  1. Coat the oil seal lip with MP grease.


8. INSTALL REAR OUTPUT SHAFT BEARING

C087994E03
  1. Using SST and a hammer, tap in the rear bearing (outer race) to the transaxle case.

    SST
    09950-60020   (09951-00680)
    09950-70010   (09951-07100)

    Standard clearance:
    3.8 to 4.4 mm (0.150 to 0.173 in.)


9. INSTALL OUTPUT SHAFT COVER

C069709E01
  1. Coat the shaft cover with MP grease, and install it to the transaxle case.

    NOTICE:
    Align the projection of the output shaft with the transaxle groove and install it.


10. INSTALL FRONT OUTPUT SHAFT BEARING

C087995E01
  1. Using SST and a hammer, tap in the front bearing (outer race).

    SST
    09950-60020   (09951-00730)
    09950-70010   (09951-07100)


11. ADJUST OUTPUT SHAFT BEARING PRELOAD

C083254E01
  1. Install the output shaft to the transaxle case.

  1. C083227E02
    Install the transaxle case to the transaxle case with the 14 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

  1. C083226E02
    Install the 3 bolts on the transaxle side.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

  1. C083255E01
    Install the output shaft rear bearing shim to the output shaft.

  1. C083256E01
    Using a T45 "torx" socket, install the rear bearing retainer to the transaxle case with the 7 "torx" screws.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. C069773E01
    Turn the output shaft in both directions and check that it turns smoothly.

  1. Temporarily install the output shaft rear set nut.

  1. Using a socket wrench and torque wrench, inspect the preload.

    Standard preload:
    Bearing
    Specified Condition
    New
    0.8 to 1.6 N*m (8.16 to 16.32 kgf*cm, 7.1 to 14.2 in.lbf)
    Used
    0.5 to 1.0 N*m (5.10 to 10.20 kgf*cm, 4.4 to 8.9 in.lbf)

  1. If preload is out of the specification, select a proper output shaft rear bearing shim and adjust the preload.

    HINT:
    The preload of all the output shaft rear bearing shims varies in torque from about 0.04 to 0.06 N*m (0.408 to 0.612 kgf*cm, 0.354 to 0.531 in.*lbf).

    Standard shim thickness:
    Part No
    Mark
    Thickness
    90564-59001
    0
    1.30 mm (0.0512 in.)
    90564-59002
    1
    1.35 mm (0.0531 in.)
    90564-59003
    2
    1.40 mm (0.0551 in.)
    90564-59004
    3
    1.45 mm (0.0571 in.)
    90564-59005
    4
    1.50 mm (0.0591 in.)
    90564-59006
    5
    1.55 mm (0.0610 in.)
    90564-59007
    6
    1.60 mm (0.0630 in.)
    90564-59008
    7
    1.65 mm (0.0650 in.)
    90564-59009
    8
    1.70 mm (0.0669 in.)
    90564-59010
    9
    1.75 mm (0.0689 in.)
    90564-59011
    A
    1.80 mm (0.0669 in.)
    90564-59012
    B
    1.85 mm (0.0728 in.)
    90564-59013
    C
    1.90 mm (0.0748 in.)
    90564-59014
    D
    1.95 mm (0.0768 in.)
    90564-59015
    E
    2.00 mm (0.787 in.)
    90564-59016
    F
    2.05 mm (0.0807 in.)
    90564-59017
    G
    2.10 mm (0.0827 in.)
    90564-59018
    H
    2.15 mm (0.0846 in.)
    90564-59019
    J
    2.20 mm (0.0866 in. )
    90564-59020
    K
    2.25 mm (0.0886 in.)
    90564-59021
    L
    2.30 mm (0.0906 in.)
    90564-59022
    M
    2.35 mm (0.0925 in.)
    90564-59023
    N
    2.40 mm (0.0945 in.)
    90564-59024
    P
    2.45 mm (0.0965 in.)
    90564-59025
    Q
    2.50 mm (0.0984 in.)

  1. Remove the output shaft rear set nut from the output shaft.

  1. C083258E01
    Using a T45 "torx" socket, remove the 7 "torx" screws and rear bearing retainer from the manual transaxle case.

  1. C083255E02
    Remove the output shaft rear bearing shim from the output shaft.

  1. C083226E03
    Remove the 3 bolts.

  1. C083227E03
    Remove the 14 bolts and transaxle case from the transaxle case.

  1. C083254E02
    Remove the output shaft assembly from the front transaxle case.


12. ADJUST TAPERED ROLLER BEARING PRELOAD

  1. C083242E02
    Install the bearing to the transaxle case.

  1. C083227E04
    Install the 14 bolts and transaxle case to the transaxle case.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

  1. C083226E04
    Install the 3 bolts on the front transaxle case side.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

  1. Turn the differential case in both directions and check that it turns smoothly.

  1. C087996E01
    Using SST and a torque wrench, measure the preload.
    SST
    09564-32011  

    Standard preload:
    Bearing
    Specified Condition
    New
    0.8 to 1.6 N*m (8.16 to 16.32 kgf*cm, 7.1 to 14.2 in.*lbf)
    Used
    0.5 to 1.0 N*m (5.10 to 10.2 kgf*cm, 4.4 to 8.9 in.*lbf)

    If the preload is out of the specification, select a proper front differential case rear shim and adjust the preload.

    HINT:
    The preload of all the front differential case rear shims varies in torque from about 0.04 to 0.06 N*m (0.408 to 0.612 kgf*cm, 0.354 to 0.531 in.*lbf).

    Standard shim thickness:
    Part No.
    Mark
    Thickness
    90564-56055
    0
    2.00 mm (0.0787 in.)
    90564-56056
    1
    2.05 mm (0.0807 in.)
    90564-56057
    2
    2.10 mm (0.0827 in.)
    90564-56058
    3
    2.15 mm (0.0846 in.)
    90564-56059
    4
    2.20 mm (0.0866 in.)
    90564-56060
    5
    2.25 mm (0.0886 in.)
    90564-56061
    6
    2.30 mm (0.0906 in.)
    90564-56062
    7
    2.35 mm (0.0925 in.)
    90564-56063
    8
    2.40 mm (0.0945 in.)
    90564-56064
    9
    2.45 mm (0.0965 in.)
    90564-56065
    A
    2.50 mm (0.0984 in.)
    90564-56066
    B
    2.55 mm (0.1004 in.)
    90564-56067
    C
    2.60 mm (0.1024 in.)
    90564-56068
    D
    2.65 mm (0.1043 in.)
    90564-56069
    E
    2.70 mm (0.1063 in.)
    90564-56070
    F
    2.75 mm (0.1083 in.)
    90564-56071
    G
    2.80 mm (0.1102 in.)
    90564-56072
    H
    2.85 mm (0.1122 in.)

  1. C083226E05
    Remove the 3 bolts.

  1. C083227E05
    Remove the 14 bolts and transaxle case from the transaxle case.

  1. C083242E04
    Remove the bearing from the transaxle case.


13. INSTALL FRONT TRANSAXLE CASE OIL SEAL

C087997E01
  1. Using SST and a hammer, tap in a new oil seal to the transaxle case.

    SST
    09950-60010   (09951-00420)
    09950-70010   (09951-07150)

    Standard distance:
    1 to 2 mm (0.04 to 0.08 in.)

  1. Coat the lip of the oil seal with MP grease.


14. INSTALL FRONT INPUT SHAFT BEARING

C087998E01
  1. Coat the input shaft front bearing with gear oil, and using SST, tap in it to the transaxle case.

    SST
    09950-60010   (09951-00570)
    09950-70010   (09951-07150)

    Standard distance:
    4.28 to 4.60 mm (0.1685 to 0.1811 in.)


15. INSTALL MANUAL TRANSAXLE CASE RECEIVER

C083243E02
  1. Install the receiver to the transaxle case with the 3 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }


16. INSTALL DIFFERENTIAL CASE ASSEMBLY

C083242E05
  1. Coat the differential case tapered roller bearing with gear oil, and install the differential case to the transaxle case.


17. INSTALL OUTPUT SHAFT ASSEMBLY

C083241E02
  1. Apply gear oil to each sliding part of the output shaft.

  1. Slightly lift up on the differential case at an angle, and install the output shaft to the transaxle case.


18. INSTALL INPUT SHAFT ASSEMBLY

C083240E02
  1. Apply gear oil to each sliding part of the input shaft.

  1. Install the input shaft to the transaxle case while tilting the output shaft.


19. INSTALL NO. 2 GEAR SHIFT FORK

C087999E01
  1. Coat the No. 2 gear shift fork with gear oil, and install it to the input shaft assembly.


20. INSTALL NO. 3 GEAR SHIFT FORK

C083257E01
  1. Install the reverse shift fork to the No. 3 gear shift fork shaft.

  1. Using a brass bar and hammer, tap in the 2 shift fork shaft snap rings to the No. 3 gear shift fork shaft.

  1. C088000E01
    Apply gear oil to each sliding part of the No. 3 gear shift fork shaft, and install it to the transaxle case.


21. INSTALL NO. 1 GEAR SHIFT FORK

C088001E01
  1. Apply gear oil to each sliding part of the No. 1 gear shift fork, and install it to the output shaft assembly.


22. INSTALL NO. 2 GEAR SHIFT FORK

C088002E01
  1. Apply gear oil to each sliding part of the No. 2 gear shift fork shaft and No. 1 gear shift head, and install them to the transaxle case.

  1. C083234E02
    Install the shift fork set bolt and shift head set bolt to the No. 1 gear shift head and No. 2 gear shift fork.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }


23. INSTALL REVERSE SHIFT FORK ROLLER

C083233E02
  1. Using a magnetic finger, install the reverse shift fork roller to the reverse shift fork.


24. INSTALL NO. 1 GEAR SHIFT FORK SHAFT

C069752E01
  1. Using a brass bar and hammer, tap in the shaft snap ring to the No. 1 shift fork shaft.

  1. C088003E01
    Install the No. 1 gear shift fork shaft to the transaxle case.

  1. C083231E02
    Install the shift fork set bolt to the No. 1 gear shift fork.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }


25. INSTALL REVERSE SHIFT ARM BRACKET ASSEMBLY

C083230E02
  1. Install the reverse shift arm bracket to the transaxle case with the 2 bolts.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }


26. INSTALL REVERSE IDLER GEAR SUB-ASSEMBLY

C070512E02
  1. Coat the reverse idler gear and thrust washer with gear oil, and install them to the reverse idler gear shaft.

  1. C069753E01
    Install the reverse idler gear with the reverse idler gear shaft to the transaxle case.

    HINT:
    Align the mark of the reverse idler gear shaft with the hole of the bolts.


27. INSTALL TRANSAXLE MAGNET

C083229E01
  1. Clean the transaxle magnet, and install it to the transaxle case.


28. INSTALL REVERSE RESTRICT PIN ASSEMBLY

  1. C135411
    Install the transmission oil baffle and reverse restrict pin with the bolt.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }

  1. C069759E01
    Install the reverse restrict pin to the transaxle case.

  1. Using a 5 mm pin punch and hammer, tap in the slotted spring pin.

    Standard clearance:
    12.5 to 13.5 mm (0.492 to 0.531 in.)

  1. C070521E02
    Coat the reverse restrict pin plug with adhesive. Using a 6 mm hexagon wrench, install the plug to the manual transaxle case.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or Equivalent

    Torque:
    13 N*m{ 133 kgf*cm , 9.6 ft.*lbf }


29. INSTALL NO. 1 OIL RECEIVER PIPE

C138375
  1. Install the oil receiver pipe to the transaxle case with the bolt.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }

    NOTICE:
    Do not damage the pipe.


30. INSTALL NO. 2 OIL RECEIVER PIPE

C138376
  1. Install the oil receiver pipe to the transaxle case with the bolt.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }

    NOTICE:
    Do not damage the pipe.


31. INSTALL MANUAL TRANSAXLE CASE

C069755E02
  1. Apply seal packing to the transaxle case in a continuous line, as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent

    NOTICE:
    Install the part within 10 minutes after applying packing material.

  1. C083227E06
    Install the transaxle case to the transaxle case with the 14 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

  1. C083226E06
    Coat the 3 bolts with adhesive, and install them on the transaxle case side.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or Equivalent


32. INSTALL CLUTCH TUBE BRACKET
  1. Install the clutch tube bracket with the bolt.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }


33. INSTALL REVERSE IDLER GEAR SHAFT BOLT

C083225E02
  1. Coat the reverse idler gear shaft bolt with adhesive, and install a new reverse idler gear shaft gasket and the reverse idler gear shaft bolt to the transaxle case.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or Equivalent


34. INSTALL SHIFT FORK SHAFT SHAFT SNAP RING

C069758E01
  1. Using a brass bar and hammer, tap in the shaft snap ring to the No. 1 gear shift fork shaft.

  1. C069757E02
    Using a brass bar and hammer, tap in the shaft snap ring to the No. 2 gear shift fork shaft.


35. INSTALL INPUT SHAFT REAR BEARING SHAFT SNAP RING

C088004E01
  1. Using a snap ring expander, install the shaft snap ring.


36. INSTALL OUTPUT SHAFT REAR BEARING SHIM

C069458E02
  1. Install the output shaft rear bearing shim to the output shaft.


37. INSTALL REAR BEARING RETAINER

C083259E01
  1. Coat the 7 bolts with adhesive. Using a T45 "torx" socket, install the bearing retainer with the bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or Equivalent


38. INSTALL 5TH DRIVEN GEAR

C095786E01
  1. Using SST, install the 5th driven gear to the output shaft.

    SST
    09309-12020  


39. INSTALL 5TH GEAR NEEDLE ROLLER BEARING

C069455E02
  1. Coat the needle roller bearing with gear oil, and install it to the input shaft.


40. INSTALL 5TH GEAR

C069454E02
  1. Coat the 5th gear with gear oil, and install it to the input shaft.


41. INSTALL NO. 3 TRANSAXLE CLUTCH HUB

C088006E01
  1. Using SST, install the No. 3 transaxle clutch hub to the input shaft.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010)

    NOTICE:
    Align the projection of the synchronizer ring with the hole of the 5th gear and install it.

  1. C069746E01
    Install the No. 3 transaxle hub sleeve and No. 3 gear shift fork to the No. 3 transaxle clutch hub.

  1. C083260E01
    Coat the shift fork set bolt with adhesive, and install it to the No. 3 gear shift fork.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or Equivalent

  1. C069763E01
    Select an appropriate No. 3 transaxle clutch hub shaft snap ring that allows the minimum amount of axial play. Using a brass bar and hammer, tap in the No. 3 transaxle clutch hub shaft snap ring.

    Standard clearance:
    0.1 mm (0.004 in.) or less

    Standard snap ring:
    Part No.
    Mark
    Thickness
    90520-27061
    a
    1.75 to 1.80 mm (0.0689 to 0.0709 in.)
    90520-27062
    b
    1.80 to 1.85 mm (0.0709 to 0.0728 in.)
    90520-27063
    c
    1.85 to 1.90 mm (0.0728 to 0.0748 in.)
    90520-27064
    d
    1.90 to 1.95 mm (0.0748 to 0.0768 in.)
    90520-27065
    e
    1.95 to 2.00 mm (0.0768 to 0.0787 in.)
    90520-27066
    f
    2.00 to 2.05 mm (0.0787 to 0.0807 in.)
    90520-27067
    g
    2.05 to 2.10 mm (0.0807 to 0.0827 in.)
    90520-27068
    h
    2.10 to 2.15 mm (0.0827 to 0.0846 in.)
    90520-27069
    j
    2.15 to 2.20 mm (0.0846 to 0.0866 in.)


42. INSPECT 5TH GEAR RADIAL CLEARANCE

C069516E03
  1. Using a dial indicator, measure the 5th gear radial clearance.

    Standard clearance:
    0.009 to 0.050 mm (0.0004 to 0.0020 in.)
    If the clearance is out of the specification, replace the 5th gear, 5th gear needle roller bearing or input shaft.


43. INSPECT 5TH GEAR THRUST CLEARANCE

C069517E03
  1. Using a dial indicator, measure the 5th gear thrust clearance.

    Standard clearance:
    0.10 to 0.65 mm (0.0039 to 0.0260 in.)
    If the clearance is out of the specification, replace the No. 3 transaxle clutch hub, 5th gear or input shaft rear radial ball bearing.


44. INSTALL MANUAL TRANSAXLE OUTPUT SHAFT REAR SET NUT

C069266E03
  1. Engage the 2 gears simultaneously to lock the transaxle.

  1. C090287E02
    Install a new transaxle output shaft rear set nut.

    Torque:
    123 N*m{ 1,254 kgf*cm , 90 ft.*lbf }

  1. C069766E02
    Using a chisel and hammer, stake the rear set nut.

  1. Disengage the 2 gears.


45. INSTALL MANUAL TRANSAXLE CASE COVER SUB-ASSEMBLY

C069756E02
  1. Apply seal packing to the transaxle case cover, as shown in the illustration.

    Seal packing:
    Toyota genuine seal packing black, Three Bond 1207B or Equivalent

    NOTICE:
    Install the part within 10 minutes after applying packing material.

  1. C083219E02
    Install the transaxle case cover to the transaxle case with the 10 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


46. INSTALL DRAIN PLUG SUB-ASSEMBLY

C087967E03
  1. Install a new gasket and the drain plug to the transaxle case.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


47. INSTALL MANUAL TRANSAXLE FILLER PLUG

C070824E03
  1. Install a new gasket and the filler plug to the transaxle case.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


48. INSTALL SHIFT AND SELECT LEVER SHAFT ASSEMBLY

C138371
  1. Coat the shift and select lever shaft with gear oil, and install it to the transaxle case.


49. INSTALL CONTROL SHAFT COVER

C092834E02
  1. Coat the 4 bolts with adhesive, and install a new gasket and the control shaft cover with the 4 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or Equivalent

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


50. INSTALL BACK-UP LIGHT SWITCH ASSEMBLY

C087966E03
  1. Install a new gasket and the back-up light switch to the manual transaxle case.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }


51. INSTALL MANUAL TRANSAXLE BREATHER PLUG

C087965E03
  1. Install a new gasket and the breather plug to the case.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


52. INSTALL NO. 1 LOCK BALL ASSEMBLY

C087964E02
  1. Install the No. 1 lock ball to the transaxle case.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


53. INSTALL CONTROL SHIFT LEVER

C092832E02
  1. Install the control shift lever with the shift outer lever lock pin to the shift and select lever shaft.

  1. Install the spring washer with the nut.

    Torque:
    6.4 N*m{ 65 kgf*cm , 57 in.*lbf }


54. INSTALL SELECTING BELLCRANK ASSEMBLY

C092831E02
  1. Install the shift and select lever bush to the selecting bellcrank.

  1. Coat the 2 bolts with adhesive, and install the selecting bellcrank to the transaxle case with the bolts.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or Equivalent

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


55. INSTALL SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY
  1. Install a new O-ring to the hole cover.

  1. Install the hole cover to the transaxle case with the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 48 ft.*lbf }


56. INSTALL CLUTCH RELEASE FORK BOOT
  1. Install the clutch release fork boot to the transaxle case.


57. INSTALL RELEASE FORK SUPPORT

C083809E02
  1. Using a deep socket wrench, install the release fork support to the transaxle case.

    Torque:
    47 N*m{ 480 kgf*cm , 35 in.*lbf }


58. INSTALL CLUTCH RELEASE BEARING ASSEMBLY
  1. Coat the clutch release bearing with release hub grease, and install it to the clutch release fork with the clutch release bearing clip.

    Release hub grease:
    Part No. 08887-01806, Release Hub Grease or Equivalent


59. INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY

C069774E02
  1. Apply clutch spline grease to the input shaft spline.

    Clutch spline grease:
    Part No. 08887-01806, Clutch Spline Grease or Equivalent

  1. Install the clutch release fork to the input shaft.

← INSPECTION (from Nov 2005)COMPONENTS (from Nov 2005) →