2005-2008 RAV4 · Service Manual TRANSMISSION

DISASSEMBLY

Removal / installation · Vehicles built from Nov 2005


1. INSPECT 1ST GEAR THRUST CLEARANCE

C068252E01
  1. Using a feeler gauge, measure the thrust clearance.

    Standard clearance:
    0.25 to 0.40 mm (0.0098 to 0.0157 in.)

    If the clearance is out of the specification, replace the 1st gear or No. 1 transaxle clutch hub.


2. INSPECT 2ND GEAR THRUST CLEARANCE

C069637E02
  1. Using a dial indicator, measure the thrust clearance.

    Standard clearance:
    0.10 to 0.35 mm (0.0039 to 0.0138 in.)

    If the clearance is out of the specification, replace the No. 1 transaxle clutch hub, 2nd gear or 3rd driven gear.


3. INSPECT 1ST GEAR RADIAL CLEARANCE

C069638E01
  1. Using a dial indicator, measure the radial clearance.

    Standard clearance:
    Bearing
    Specified Condition
    KOYO made
    0.009 to 0.053 mm (0.0004 to 0.0021 in.)
    NSK made
    0.009 to 0.051 mm (0.0004 to 0.0020 in.)

    If the clearance is out of the specification, replace the 1st gear and 1st gear needle roller bearing.


4. INSPECT 2ND GEAR RADIAL CLEARANCE

C069639E01
  1. Using a dial indicator, measure the radial clearance.

    Standard clearance:
    Bearing
    Specified Condition
    KOYO made
    0.009 to 0.053 mm (0.0004 to 0.0021 in.)
    NSK made
    0.009 to 0.051 mm (0.0004 to 0.0020 in.)

    If the clearance is out of the specification, replace the 2nd gear, 2nd gear bush and 2nd gear needle roller bearing.


5. REMOVE 4TH DRIVEN GEAR

C092858E01
  1. Using SST and a press, press out the output shaft rear bearing (inner race) and 4th driven gear.

    SST
    09950-00020  


6. REMOVE OUTPUT GEAR SPACER

C069641E01
  1. Remove the output gear spacer from the output shaft.


7. REMOVE 2ND GEAR

C092859E01
  1. Using SST and a press, press out the 3rd driven gear and 2nd gear from the output shaft.

    SST
    09950-00020  


8. REMOVE NO. 2 SYNCHRONIZER RING SET

C069643E01
  1. Remove the No. 2 synchronizer ring set from the No. 1 transaxle clutch hub.


9. REMOVE 2ND GEAR NEEDLE ROLLER BEARING

C069644E01
  1. Remove the needle roller bearing from the output shaft.


10. REMOVE 2ND GEAR BEARING SPACER

C069645E01
  1. Remove the bearing spacer from the output shaft.


11. REMOVE 2ND GEAR BUSH

C069646E01
  1. Remove the bush from the output shaft.


12. REMOVE 2ND GEAR BUSH BALL

C083814E01
  1. Using a magnetic finger, remove the bush ball from the output shaft.


13. REMOVE 1ST GEAR

C092860E01
  1. Using SST and a press, remove the No. 1 transaxle clutch hub and 1st gear from the output shaft.

    SST
    09950-00020  


14. REMOVE NO. 1 SYNCHRONIZER RING SET

C069649E01
  1. Remove the No. 1 synchronizer ring set from the 1st gear.


15. REMOVE 1ST GEAR NEEDLE ROLLER BEARING

C069650E01
  1. Remove the needle roller bearing from the output shaft.


16. REMOVE FRONT OUTPUT SHAFT BEARING

C092861E01
  1. Using SST and a press, press out the front bearing (inner race) from the output shaft.

    SST
    09950-00020  
    09950-60010   (09951-00320)
    09950-70010   (09951-07150)

    NOTICE:
    Do not overtighten SST.


17. REMOVE REVERSE GEAR

C069652E01
  1. Remove the No. 1 transaxle clutch hub, 3 No. 1 synchromesh shifting keys and 3 No. 1 synchromesh shifting key springs from the reverse gear.

← COMPONENTS (from Nov 2005)REASSEMBLY (from Nov 2005) →