REASSEMBLY
Removal / installation · Vehicles built from Nov 2005
| 1.
INSTALL REVERSE GEAR |
 |
Coat the reverse gear with gear oil.
Install the 3 No. 1 synchromesh shifting key springs and No. 1 transaxle clutch hub to the reverse gear.
- NOTICE:
- Assemble the reverse gear and the No. 1 transaxle clutch hub in the correct direction.
Using a screwdriver, install the 3 No. 1 synchromesh shifting keys to the reverse gear.
| 2.
INSTALL FRONT OUTPUT SHAFT BEARING |
 |
Using SST and a press, press in the front bearing (inner race) to the output shaft.
- SST
- 09950-60010
(09951-00430)
09950-70010
(09951-07150)
| 3.
INSTALL NO. 1 SYNCHRONIZER RING SET |
 |
Coat the No. 1 synchronizer ring set with gear oil, and install it to the 1st gear.
- NOTICE:
- Align the claw of the No. 1 synchronizer ring set (middle) with the hole of the 1st gear and install it.
| 4.
INSTALL 1ST GEAR NEEDLE ROLLER BEARING |
 |
Coat the needle roller bearing with gear oil, and install it to the output shaft.
| 5.
INSTALL 1ST GEAR |
 |
Coat the 1st gear with gear oil, and install it to the output shaft.
| 6.
INSTALL NO. 1 TRANSAXLE CLUTCH HUB |
 |
Using SST and a press, press in the No. 1 transaxle clutch hub to the output shaft.
- SST
- 09316-60011
(09316-00031)
09950-60010
(09951-00320)
09950-70010
(09951-07100)
- NOTICE:
- Align the claw of the No. 1 synchronizer ring set (outer) with the hole of the No. 1 transaxle clutch hub and install it.
- Make sure that the 1st gear rotates.
| 7.
INSTALL 2ND GEAR BUSH BALL |
 |
Coat the bush ball with MP grease, and install it to the output shaft.
| 8.
INSTALL 2ND GEAR BUSH |
 |
Coat the bush with gear oil, and install it to the output shaft.
| 9.
INSTALL 2ND GEAR BEARING SPACER |
 |
Coat the bearing spacer with gear oil, and install it to the output shaft.
| 10.
INSTALL 2ND GEAR NEEDLE ROLLER BEARING |
 |
Coat the needle roller bearing with gear oil, and install it to the output shaft.
| 11.
INSTALL NO. 2 SYNCHRONIZER RING SET |
 |
Coat the No. 2 synchronizer ring set with gear oil, and install it to the No. 1 transaxle clutch hub.
- NOTICE:
- Align the key groove on the No. 2 synchronizer ring set with the No. 1 synchromesh shifting key.
| 12.
INSTALL 2ND GEAR |
 |
Coat the 2nd gear with gear oil, and install it to the output shaft.
| 13.
INSTALL 3RD DRIVEN GEAR |
 |
Using SST and a press, press in the 3rd driven gear to the output shaft.
- SST
- 09608-00071
09950-60010
(09951-00320)
09950-70010
(09951-07100)
| 14.
INSTALL OUTPUT GEAR SPACER |
 |
Install the output gear spacer to the output shaft.
| 15.
INSTALL 4TH DRIVEN GEAR |
 |
Using SST and a press, press in the 4th driven gear to the output shaft.
- SST
- 09608-00071
09950-60010
(09951-00320)
09950-70010
(09951-07100)
| 16.
INSTALL FRONT OUTPUT SHAFT BEARING |
 |
Using SST and a press, press in the front bearing (inner race) to the output shaft.
- SST
- 09506-30012
09950-60010
(09951-00320)
09950-70010
(09951-07100)
| 17.
INSPECT 2ND GEAR RADIAL CLEARANCE |
 |
Using a dial indicator, measure the radial clearance.
- Standard clearance:
Bearing
|
Specified Condition
|
KOYO made
|
0.009 to 0.053 mm (0.0004 to 0.0021 in.)
|
NSK made
|
0.009 to 0.051 mm (0.0004 to 0.0020 in.)
|
If the clearance is out of the specification, replace the 2nd gear, 2nd gear bush and 2nd gear needle roller bearing.
| 18.
INSPECT 1ST GEAR RADIAL CLEARANCE |
 |
Using a dial indicator, measure the radial clearance.
- Standard clearance:
Bearing
|
Specified Condition
|
KOYO made
|
0.009 to 0.053 mm (0.0004 to 0.0021 in.)
|
NSK made
|
0.009 to 0.051 mm (0.0004 to 0.0020 in.)
|
If the clearance is out of the specification, replace the 1st gear and 1st gear needle roller bearing.
| 19.
INSPECT 2ND GEAR THRUST CLEARANCE |
 |
Using a dial indicator, measure the thrust clearance.
- Standard clearance:
- 0.10 to 0.35 mm (0.0039 to 0.0138 in.)
If the clearance is out of the specification, replace the No. 1 transaxle clutch hub, 2nd gear or 3rd driven gear.
| 20.
INSPECT 1ST GEAR THRUST CLEARANCE |
 |
Using a feeler gauge, measure the thrust clearance.
- Standard clearance:
- 0.25 to 0.40 mm (0.0098 to 0.0157 in.)
If the clearance is out of the specification, replace the 1st gear or No. 1 transaxle clutch hub.