INSTALLATION
Removal / installation · Vehicles built Jan 2007 – Jul 2007
Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007
| 1.
INSTALL REAR SEAT INNER BELT ASSEMBLY RH (for 60/40 Split Seat Type RH Side) |
 |
Install the belt with the bolt.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
| 2.
INSTALL REAR NO. 1 SEAT ASSEMBLY RH
|
 |
Fully tilt the seatback forward.
Place the seat in the cabin.
- NOTICE:
- Be careful not to damage the vehicle body.
Connection procedures of seat to lock cable when reusing seat:
- Using a screwdriver, detach the claw and remove the connector case from the seat.
- HINT:
- Tape the screwdriver tip before use.
- Install the connector case to the body's cap.
- Pull out the joint piece. Align the slits of the joint piece and connector case.
- Compress the spring of the adjuster, and pull out the cable from the seat's cap.
- HINT:
- Perform this procedure with the lock of the adjuster released.
- Install the seat cable's end part to the connector case's slit.
- HINT:
- Position the joint piece cable's end part as shown in the illustration.
- Install the seat's cap to the connector case.
Temporarily place the seat into the vehicle where it will be installed.
- Return the seatback to the upright position.
- Attach the claws of the connector and adjuster, and install them to the seat.
- Press the adjuster's lock piece to lock it.
- NOTICE:
- When pressing the lock piece, make sure the adjuster's spring is not compress.
Connection procedures of seat to lock cable when replacing seat:
- Cut the joint piece on the lock cable, and remove it.
- HINT:
- A joint piece is included with new seats.
- This procedure is not necessary when the lock cable is replaced with a new one.
Temporarily place the seat into the vehicle where it will be installed.
- Install the body's cap to the connector case.
- Press the adjuster's lock pin.
- Return the seatback to the upright position.
- Press the adjuster's lock piece to lock it.
- NOTICE:
- When pressing the lock piece, make sure the adjuster's spring is not compressed.
Lift up the seat track adjusting handle and move the seat to the foremost position.
- Tighten the 2 bolts on the rear side of the seat.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
- HINT:
- Tighten the bolts in the order indicated in the illustration.
Lift up the seat track adjusting handle and move the seat to the rearmost position.
- Tighten the 2 bolts on the front side of the seat.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
- HINT:
- Tighten the bolts in the order indicated in the illustration.
| 3.
INSTALL REAR SEAT INNER BELT ASSEMBLY RH (for 60/40 Split Seat Type LH Side) |
 |
Install the belt with the bolt.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
| 4.
INSTALL REAR SEAT LAP TYPE BELT ASSEMBLY CENTER LH |
 |
Install the belt with the bolt.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
| 5.
INSTALL REAR SEAT REAR BRACKET COVER LH
|
 |
- Open the lower part of the seatback cover. Then attach the 4 clips to install the bracket cover.
Install the 2 screws.
| 6.
INSTALL REAR NO. 1 SEAT ASSEMBLY LH
|
 |
Fully tilt the seatback forward.
Place the seat in the cabin.
- NOTICE:
- Be careful not to damage the vehicle body.
- Connection procedures of seat to lock cable when reusing seat:
Using a screwdriver, detach the claw and remove the connector case from the seat.
- HINT:
- Tape the screwdriver tip before use.
- Install the connector case to the body's cap.
- Pull out the joint piece. Align the slits of the joint piece and connector case.
- Compress the spring of the adjuster, and pull out the cable from the seat's cap.
- HINT:
- Perform this procedure with the lock of the adjuster released.
- Install the seat cable's end part to the connector case's slit.
- HINT:
- Position the joint piece cable's end part as shown in the illustration.
- Install the seat's cap to the connector case.
Temporarily place the seat into the vehicle where it will be installed.
- Return the seatback to the upright position.
- Attach the claws of the connector and adjuster, and install them to the seat.
- Press the adjuster's lock piece to lock it.
- NOTICE:
- When pressing the lock piece, make sure the adjuster's spring is not compress.
- Connection procedures of seat to lock cable when replacing seat:
Cut the joint piece on the lock cable, and remove it.
- HINT:
- A joint piece is included with new seats.
- This procedure is not necessary when the lock cable is replaced with a new one.
Temporarily place the seat into the vehicle where it will be installed.
- Install the body's cap to the connector case.
- Press the adjuster's lock pin.
- Return the seatback to the upright position.
- Press the adjuster's lock piece to lock it.
- NOTICE:
- When pressing the lock piece, make sure the adjuster's spring is not compress.
Lift up the seat track adjusting handle and move the seat to the foremost position.
- Tighten the 3 bolts on the rear side of the seat.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
- HINT:
- Tighten the bolts in the order indicated in the illustration.
Lift up the seat track adjusting handle and move the seat to the rearmost position.
- Tighten the 2 bolts on the front side of the seat.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
- HINT:
- Tighten the bolts in the order indicated in the illustration.
| 7.
INSTALL REAR SEAT LAP TYPE BELT ASSEMBLY CENTER RH |
 |
Install the belt with the bolt.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
- NOTICE:
- The anchor part of the seat belt must not overlap the protruding part.
| 8.
INSTALL REAR NO. 5 SEAT LEG SIDE COVER |
|
| 9.
INSTALL REAR NO. 4 SEAT LEG SIDE COVER |
|
| 10.
INSTALL REAR NO. 3 SEAT LEG SIDE COVER
|
 |
Attach the 4 claws to install the side cover.
| 11.
INSTALL REAR NO. 2 SEAT LEG SIDE COVER |
|
| 12.
INSTALL REAR SEAT LEG COVER |
|