2005-2008 RAV4 · Service Manual RESTRAINTS

INSTALLATION

Removal / installation · Vehicles built Nov 2005 – Dec 2006

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007


1. INSTALL REAR SEAT INNER BELT ASSEMBLY RH (for 60/40 Split Seat Type RH Side)

B138223
  1. Install the belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


2. INSTALL REAR NO. 1 SEAT ASSEMBLY RH
  1. Fully tilt the seatback forward.

  1. Place the seat in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Connection procedures of seat to lock cable when reusing seat:

    1. B140440E01
      Using a screwdriver, detach the claw and remove the connector case from the seat.

      HINT:
      Tape the screwdriver tip before use.

    2. B140542E01
      Install the connector case to the body's cap.

    3. B140544E01
      Pull out the joint piece. Align the slits of the joint piece and connector case.

    4. B140545E01
      Compress the spring of the adjuster, and pull out the cable from the seat's cap.

      HINT:
      Perform this procedure with the lock of the adjuster released.

    5. B140546E01
      B140547E01
      Install the seat cable's end part to the connector case's slit.

      HINT:
      Position the joint piece cable's end part as shown in the illustration.

    6. B140551E01
      Install the seat's cap to the connector case.

    7. Temporarily place the seat into the vehicle where it will be installed.

    8. B140548E01
      Return the seatback to the upright position.

    9. B140553E01
      Attach the claws of the connector and adjuster, and install them to the seat.

    10. B140550E01
      Press the adjuster's lock piece to lock it.

      NOTICE:
      When pressing the lock piece, make sure the adjuster's spring is not compress.

  1. Connection procedures of seat to lock cable when replacing seat:

    1. B140437E01
      Cut the joint piece on the lock cable, and remove it.

      HINT:
      1. A joint piece is included with new seats.
      2. This procedure is not necessary when the lock cable is replaced with a new one.

    2. Temporarily place the seat into the vehicle where it will be installed.

    3. B140438E01
      Install the body's cap to the connector case.

    4. B140439E01
      Press the adjuster's lock pin.

    5. B140548E01
      Return the seatback to the upright position.

    6. B140550E01
      Press the adjuster's lock piece to lock it.

      NOTICE:
      When pressing the lock piece, make sure the adjuster's spring is not compressed.

  1. Lift up the seat track adjusting handle and move the seat to the foremost position.

  1. B131535E01
    Tighten the 2 bolts on the rear side of the seat.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    HINT:
    Tighten the bolts in the order indicated in the illustration.

  1. Lift up the seat track adjusting handle and move the seat to the rearmost position.

  1. B131536E02
    Tighten the 2 bolts on the front side of the seat.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    HINT:
    Tighten the bolts in the order indicated in the illustration.


3. INSTALL REAR SEAT INNER BELT ASSEMBLY RH (for 60/40 Split Seat Type LH Side)

B138224
  1. Install the belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


4. INSTALL REAR SEAT LAP TYPE BELT ASSEMBLY CENTER LH

B130992
  1. Install the belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


5. INSTALL REAR SEAT REAR BRACKET COVER LH

  1. B135844
    Open the lower part of the seatback cover. Then attach the 4 clips to install the bracket cover.

  1. Install the 2 screws.


6. INSTALL REAR NO. 1 SEAT ASSEMBLY LH
  1. Fully tilt the seatback forward.

  1. Place the seat in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. B140441E01
    Connection procedures of seat to lock cable when reusing seat:

    1. Using a screwdriver, detach the claw and remove the connector case from the seat.

      HINT:
      Tape the screwdriver tip before use.

    2. B141253E01
      Install the connector case to the body's cap.

    3. B140544E01
      Pull out the joint piece. Align the slits of the joint piece and connector case.

    4. B140545E01
      Compress the spring of the adjuster, and pull out the cable from the seat's cap.

      HINT:
      Perform this procedure with the lock of the adjuster released.

    5. B141254E01
      B140547E01
      Install the seat cable's end part to the connector case's slit.

      HINT:
      Position the joint piece cable's end part as shown in the illustration.

    6. B140551E01
      Install the seat's cap to the connector case.

    7. Temporarily place the seat into the vehicle where it will be installed.

    8. B140549E01
      Return the seatback to the upright position.

    9. B140552E01
      Attach the claws of the connector and adjuster, and install them to the seat.

    10. B140550E01
      Press the adjuster's lock piece to lock it.

      NOTICE:
      When pressing the lock piece, make sure the adjuster's spring is not compress.

  1. B140437E01
    Connection procedures of seat to lock cable when replacing seat:

    1. Cut the joint piece on the lock cable, and remove it.

      HINT:
      1. A joint piece is included with new seats.
      2. This procedure is not necessary when the lock cable is replaced with a new one.

    2. Temporarily place the seat into the vehicle where it will be installed.

    3. B140438E01
      Install the body's cap to the connector case.

    4. B140439E01
      Press the adjuster's lock pin.

    5. B140549E01
      Return the seatback to the upright position.

    6. B140550E01
      Press the adjuster's lock piece to lock it.

      NOTICE:
      When pressing the lock piece, make sure the adjuster's spring is not compress.

  1. Lift up the seat track adjusting handle and move the seat to the foremost position.

  1. B135840E01
    Tighten the 3 bolts on the rear side of the seat.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    HINT:
    Tighten the bolts in the order indicated in the illustration.

  1. Lift up the seat track adjusting handle and move the seat to the rearmost position.

  1. B131536E01
    Tighten the 2 bolts on the front side of the seat.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    HINT:
    Tighten the bolts in the order indicated in the illustration.


7. INSTALL REAR SEAT LAP TYPE BELT ASSEMBLY CENTER RH

B138225E01
  1. Install the belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    The anchor part of the seat belt must not overlap the protruding part.


8. INSTALL REAR NO. 5 SEAT LEG SIDE COVER

9. INSTALL REAR NO. 4 SEAT LEG SIDE COVER

10. INSTALL REAR NO. 3 SEAT LEG SIDE COVER

B131530
Attach the 4 claws to install the side cover.

11. INSTALL REAR NO. 2 SEAT LEG SIDE COVER

12. INSTALL REAR SEAT LEG COVER
← REMOVAL (from Jan 2007)INSTALLATION (Jan 2007 – Jul 2007) →