Back Door Entry Lock and Unlock Functions do not Operate
Circuit diagnosis · Vehicles built from Nov 2005
DESCRIPTION
Neither the entry nor unlock functions operate when: 1) nothing is output from the door electrical key oscillator (back door), 2) the entry and start system is disabled through customization, or 3) the entire power door lock control system is malfunctioning.WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK FOR DTC |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
By following the tester screen display, check whether any DTCs are output.
- OK:
- No DTC output.
|
|
||||
| OK | |
| 2. CHECK MANUAL DOOR LOCK AND UNLOCK OPERATION |
Check that all the doors lock when the door control switch (for manual operation) is turned to LOCK and all doors unlock when turned to UNLOCK.
- OK:
- All doors can be locked and unlocked with door control switch.
|
|
||||
| OK | |
| 3. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DOOR ELECTRICAL KEY OSCILLATOR) |
Select the Active Test, use the intelligent tester to generate a control command, and then check that the oscillator operates.
Certification ECU: Item
Test Details
Diagnostic Note
Outside Trunk/Backdoor Transmitter
Door electrical key oscillator (back door) ON / OFF
-
- OK:
- When key is brought close to door oscillator that is ON, indicator light on key illuminates.
|
|
||||
| NG | |
| 4. CHECK WIRE HARNESS (CERTIFICATION ECU - DOOR ELECTRICAL KEY OSCILLATOR) |
![]() ![]() |
Disconnect the E63 ECU connector.
Disconnect the S8 oscillator connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
E63-31 (CLG9) - S8-5 (CLGB)
Below 1 Ω
E63-32 (CG9B) - S8-10 (CLG)
E63-31 (CLG9) or S8-5 (CLGB) - Body ground
10 kΩ or higher
E63-32 (CG9B) or S8-10 (CLG) - Body ground
|
|
||||
| OK | |
| 5. CHECK WIRE HARNESS (DOOR ELECTRICAL KEY OSCILLATOR - DOOR ELECTRICAL KEY ANTENNA) |
![]() ![]() |
Disconnect the S8 oscillator connector.
Disconnect the S9 antenna connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
S8-2 (SGT) - S9-6 (SGT)
Below 1 Ω
S8-3 (ANT1) - S9-5 (ANT1)
S8-8 (ANT2) - S9-2 (ANT2)
S8-9 (TRG-) - S9-1 (TRG-)
S8-2 (SGT) or S9-6 (SGT) - Body ground
10 kΩ or higher
S8-3 (ANT1) or S9-5 (ANT1) - Body ground
S8-8 (ANT2) or S9-2 (ANT2) - Body ground
S8-9 (TRG-) or S9-1 (TRG-) - Body ground
|
|
||||
| OK | |
| 6. CHECK WIRE HARNESS (DOOR ELECTRICAL KEY OSCILLATOR - BATTERY AND BODY GROUND) |
![]() ![]() |
Disconnect the S8 oscillator connector.
Measure the resistance and voltage of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
S9-7 (GND) - Body ground
Below 1 Ω
- Standard voltage:
Tester Connection
Specified Condition
S9-1 (+B) - Body ground
10 to 14 V
|
|
||||
| OK | |
| 7. CHECK WIRE HARNESS (DOOR ELECTRICAL KEY ANTENNA - CERTIFICATION ECU) |
![]() ![]() |
Disconnect the S9 antenna connector.
Disconnect the E62 ECU connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
S9-3 (TRG+) - E63-7 (TSW9)
Below 1 Ω
S9-3 (TRG+) or E63-7 (TSW9) - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 8. CHECK BACK DOOR OUTSIDE HANDLE (OPERATION) |
Temporarily replace the back door outside handle with a new or normally functioning one.
Check that the entry lock and unlock functions operate normally (Click here).
- OK:
- Entry lock and unlock functions operate normally.
|
|
||||
| OK | |
| 9. CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION) |
Temporarily replace the door electrical key oscillator (back door) with a new or normally
Check that the entry lock and unlock functions operate normally.
- OK:
- Entry lock and unlock functions operate normally.
|
|
||||
| OK | ||
| ||




