Back Door Entry Unlock Function does not Operate
Circuit diagnosis · Vehicles built from Nov 2005
DESCRIPTION
When an ID code from the door electrical key oscillator (back door) matches the ID code from the key, the certification ECU outputs an SEL signal (Lo when output) to the door electrical key oscillator (back door), activates the touch sensor located on the backside of the outside door handle, and enters unlock standby mode. When the touch sensor is touched, the door electrical key oscillator (back door) sends an SENS signal (Lo when output) to the certification ECU and the certification ECU sends an unlock signal to the back door lock.WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK FOR DTC |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
By following the tester screen display, check whether any DTCs are output.
- OK:
- No DTC output.
|
|
||||
| OK | |
| 2. CHECK MANUAL DOOR UNLOCK OPERATION |
Check that all the doors unlock when the door control switch (for manual operation) is turned to UNLOCK.
- OK:
- All doors can be unlocked with door control switch.
|
|
||||
| OK | |
| 3. CHECK WIRELESS DOOR LOCK CONTROL OPERATION |
Check that the wireless door lock and unlock functions operate normally (Click here).
- OK:
- Wireless door lock and unlock functions operate normally.
|
|
||||
| OK | |
| 4. READ VALUE USING INTELLIGENT TESTER (DOOR COURTESY SWITCH) |
Check the Data List for proper functioning of the back door courtesy light switch.
Main body ECU: Item
Measurement Item / Range (Display)
Normal Condition
Diagnostic Note
Back Door Courtesy SW
Back door courtesy light switch signal / ON or OFF
ON: Back door is open
OFF: Back door is closed
-
- OK:
- On tester screen, item changes between ON and OFF according to above chart.
|
|
||||
| OK | |
| 5. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (BACK DOOR SELECT) |
Select the Active Test, use the intelligent tester to generate a control command, and then check that the door electrical key oscillator operates.
Certification ECU: Item
Test Details
Diagnostic Note
Back Door Select
Door electrical key oscillator (back door) ON / OFF
-
- OK:
- ON (Outside Trunk/Backdoor Transmitter is ON) appears on screen.
|
|
||||
| OK | |
| 6. READ VALUE USING INTELLIGENT TESTER (BACK DOOR UNLOCK SWITCH) |
With "Back Door Select" ON, check the Data List to confirm the operation of the touch sensor.
Certification ECU: Item
Measurement Item / Range (Display)
Normal Condition
Diagnostic Note
B-Door Touch Sensor
Back door touch sensor / ON or OFF
ON: Sensor touch is touched
OFF: Sensor touch is not touched
-
- OK:
- When back door sensor is set to ON, ON (sensor is touched) appears on screen.
|
|
||||
| OK | |
| 7. CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (OPERATION) |
Temporarily replace the instrument panel junction block (main body ECU) with a new or normally functioning one.
Check that the entry back door unlock function operates normally.
- OK:
- Entry back door unlock function operates normally.
|
|
||||
| OK | ||
| ||
| 8. CHECK DOOR ELECTRICAL KEY OSCILLATOR (for Back Door) |
![]() ![]() |
Measure the resistance of the oscillator.
- Standard voltage:
Tester Connection
Condition
Specified Condition
4 (SEL) - Body ground
During Active Test
Below 1 V
6 (SENS) - Body ground
Touch sensor is touched during Active Test
Below 1 V
Touch sensor is not touched during Active Test
10 to 14 V
|
|
||||
| NG | |
| 9. CHECK WIRE HARNESS (DOOR ELECTRICAL KEY OSCILLATOR - ELECTRICAL KEY ANTENNA) |
![]() ![]() |
Disconnect the S8 oscillator connector.
Disconnect the S9 antenna connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
S8-2 (SGT) - S9-6 (SGT)
Below 1 Ω
S8-3 (ANT1) - S9-5 (ANT1)
S8-8 (ANT2) - S9-2 (ANT2)
S8-9 (TRG-) - S9-1 (TRG-)
S8-2 (SGT) or S9-6 (SGT) - Body ground
10 kΩ or higher
S8-3 (ANT1) or S9-5 (ANT1) - Body ground
S8-8 (ANT2) or S9-2 (ANT2) - Body ground
S8-9 (TRG-) or S9-1 (TRG-) - Body ground
|
|
||||
| OK | |
| 10. CHECK WIRE HARNESS (CERTIFICATION ECU - DOOR ELECTRICAL KEY OSCILLATOR) |
![]() ![]() |
Disconnect the E63 ECU connector.
Disconnect the S8 oscillator connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
E63-37 (SEL9) - S8-4 (SEL)
Below 1 Ω
E63-26 (SEN9) - S8-6 (SENS)
E63-31 (CLG9) - S8-10 (CLG)
E63-32 (CG9B) - S8-5 (CLGB)
E63-37 (SEL9) or S8-4 (SEL) - Body ground
10 kΩ or higher
E63-26 (SEN9) or S8-6 (SENS) - Body ground
E63-31 (CLG9) or S8-10 (CLG) - Body ground
E63-32 (CG9B) or S8-5 (CLGB) - Body ground
|
|
||||
| OK | ||
| ||



