2005-2008 RAV4 · Service Manual DRIVE LINE

REMOVAL

Removal / installation · Vehicles built Jan 2007 – Jul 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007


1. REMOVE FRONT WHEEL

2. DRAIN AUTOMATIC TRANSAXLE FLUID
  1. Remove the drain plug and gasket, and drain ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    47 N*m{ 479 kgf*cm , 35 ft.*lbf }


3. DRAIN TRANSAXLE OIL
  1. Remove the filler plug and gasket.

  1. Remove the drain plug and gasket, and drain the oil.

  1. Install a new gasket and the drain plug.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


4. REMOVE FRONT AXLE HUB NUT

C129483E01
  1. Using SST and a hammer, unstake the staked part of the nut.

    SST
    09930-00010  

    NOTICE:
    Loosen the staked part of the nut completely, otherwise the screw of the drive shaft may be damaged.

  1. While applying the brakes, remove the lock axle hub nut.


5. REMOVE FRONT SPEED SENSOR LH

  1. C127964E01
    Disconnect the sensor connector.

  1. C127963E01
    Remove the sensor clip (labeled A), bolt (labeled B) and sensor clamp (labeled C).

  1. Remove the sensor clip (labeled D), bolt (labeled E) and sensor clamp (labeled F).

    C127962E01

  1. C127961E01
    Remove the bolt and sensor body from the knuckle.

    NOTICE:
    Keep the sensor tip and sensor installation hole free from foreign matter.


6. REMOVE FRONT SPEED SENSOR RH

HINT:
Use the same procedures described for the LH side.


7. DISCONNECT FRONT DISC BRAKE CYLINDER ASSEMBLY LH

C127286
  1. Remove the 2 bolts and cylinder.


8. DISCONNECT FRONT DISC BRAKE CYLINDER ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


9. REMOVE FRONT STABILIZER LINK ASSEMBLY LH

  1. C127528
    Remove the 2 nuts and stabilizer link.


10. REMOVE FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


11. DISCONNECT FRONT SUSPENSION LOWER NO. 1 ARM SUB-ASSEMBLY LH

C127531
  1. Remove the bolt and 2 nuts.

  1. Disconnect the lower arm from the ball joint.


12. DISCONNECT FRONT SUSPENSION LOWER NO. 1 ARM SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


13. DISCONNECT STEERING KNUCKLE WITH AXLE HUB LH

C129488E01
  1. Put matchmarks on the drive shaft and axle hub.

    NOTICE:
    Do not punch the marks.

  1. Using a plastic-faced hammer, disconnect the steering knuckle with axle hub.

    NOTICE:
    Be careful not to damage the boot and speed sensor rotor.
    Do not excessively push out the drive shaft from the axle assembly.


14. DISCONNECT STEERING KNUCKLE WITH AXLE HUB RH

15. DISCONNECT TIE ROD END SUB-ASSEMBLY LH
  1. Remove the cotter pin and castle nut.

  1. C132680E01
    Using SST, disconnect the tie rod end from the steering knuckle.

    NOTICE:
    Do not damage the tie rod end dust cover.

    SST
    09628-62011  


16. DISCONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


17. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH

  1. C127631E01
    Using SST, remove the front drive shaft.
    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    1. Be careful not to damage the transaxle case oil seal, inboard joint boot and drive shaft dust cover.
    2. Be careful not to drop the drive shaft.


18. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

  1. C127638
    Remove the 2 bolts and pull out the drive shaft together with the drive shaft bearing case.

  1. Remove the drive shaft from the transaxle.

    NOTICE:
    1. Be careful not to damage the inboard joint boot and drive shaft dust cover.
    2. Be careful not to drop the drive shaft.


19. FIX FRONT AXLE ASSEMBLY

C129482E01

NOTICE:
The hub bearing could be damaged if it is subjected to the vehicle weight, such as when moving the vehicle with the drive shaft removed. Therefore, if it is absolutely necessary to place the vehicle weight on the hub bearing, first support it with SST.

SST
09608-16042   (09608-02021, 09608-02041)
← REMOVAL (Nov 2005 – Dec 2006)REMOVAL (from Aug 2007) →