2005-2008 RAV4 · Service Manual DRIVE LINE

REASSEMBLY

Removal / installation · Vehicles built from Nov 2005


1. INSTALL DRIVE SHAFT BEARING CASE SUB-ASSEMBLY

C127674E01
  1. Using SST and a press, press in the drive shaft bearing case to the inboard joint RH.

    SST
    09527-10011  
    09710-04081  

    NOTICE:
    The bearing should be installed completely.

  1. C127675
    Using a snap ring expander, install a new drive shaft hole snap ring.


2. INSTALL FRONT DRIVE SHAFT DUST COVER

C127676E01
  1. Using SST and a press, press in a new drive shaft dust cover.

    SST
    09726-40010  
    09527-10011  

    NOTICE:
    Be careful not to damage the dust cover.


3. INSTALL FRONT DRIVE SHAFT DUST COVER RH

C127678E01
  1. Using SST and a press, press in a new drive shaft dust cover until the distance from the tip of the center drive shaft to the drive shaft dust cover reaches the specification, as shown in the illustration.

    SST
    09527-10011  

    Standard distance:
    91.0 to 92.0 mm (3.583 to 3.622 in.)

    NOTICE:
    1. The dust cover should be installed completely.
    2. Be careful not to damage the dust cover.


4. INSTALL FRONT DRIVE SHAFT DUST COVER LH

C127677E01
  1. Using SST and a press, press in a new drive shaft dust cover.

    SST
    09527-10011  

    NOTICE:
    1. The dust cover should be installed completely.
    2. Be careful not to damage the dust cover.


5. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH
  1. Install a new hole snap ring.


6. INSTALL FRONT AXLE OUTBOARD JOINT BOOT

C127681E01

HINT:
Before installing the boots, wrap the spline of the drive shaft with vinyl tape to prevent the boots from being damaged.

  1. Install new parts to the outboard joint shaft in the following order.

    1. No. 2 outboard joint boot clamp

    2. Outboard joint boot

    3. Outboard joint boot clamp

  1. Pack the outboard joint shaft and boot with grease from the boot kit.

    Standard grease capacity:
    Item
    Capacity
    A/T
    190 to 200 g (6.7 to 7.1 oz.)
    M/T
    205 to 215 g (7.2 to 7.6 oz.)


7. INSTALL FRONT AXLE OUTBOARD JOINT BOOT NO. 2 CLAMP LH

C127683

CAUTION:
Wear protective gloves while performing the operation and be careful to avoid cutting your hands or other body parts.

  1. Install a new boot clamp to the outboard joint boot and temporarily bend the lever.

    NOTICE:
    1. When temporarily bending the lever, make sure not to deform the band and lever.
    2. Set the clamp correctly in the guide groove and align it with the interior of the vehicle as much as possible.

  1. C127684
    With the joint on the working surface, use your body weight to press down on the joint with one hand. Then, roll the joint forward, as shown in the illustration, and press the lever in until a "click" sound is heard.

    NOTICE:
    1. Do not damage the deflector.
    2. Make sure the joint is in full contact with the joint surface at all times.

  1. C127685
    Using a plastic-faced hammer, fix the buckle into place by tapping it. At the same time, use the plastic-faced hammer to adjust the lift of the lever so that the gaps between the buckle flange and lever end flange become even.

    NOTICE:
    Do not damage the boot.


8. INSTALL FRONT AXLE OUTBOARD JOINT BOOT NO. 2 CLAMP RH

HINT:
Use the same procedures described for the LH side.


9. INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP LH

C129510

CAUTION:
Wear protective gloves while performing the operation and be careful to avoid cutting your hands or other body parts.

  1. Install a new boot clamp to the outboard joint boot and temporarily bend the lever.

    NOTICE:
    When temporarily bending the lever, make sure not to deform the band and lever.

  1. C129511
    Using water pump pliers, temporarily lock the boot clamp by clamping it down until a "click" sound is heard.

  1. C129512
    Using a plastic-faced hammer, fix the buckle into place by tapping it. At the same time, use the plastic-faced hammer to adjust the lift of the lever so that the gaps between the buckle flange and lever end flange become even.

    NOTICE:
    Do not strike the drive shaft forcefully with the plastic-faced hammer.


10. INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP RH

HINT:
Use the same procedures described for the LH side.


11. INSTALL FRONT DRIVE SHAFT DAMPER LH (for Automatic Transaxle)

C127690E01

HINT:
Install the damper clamp to outboard joint side.

  1. Install a new drive shaft damper clamp and the drive shaft damper to the drive shaft.

  1. Make sure that the damper is on the shaft groove.

  1. Set the distance, as described below.

    Standard distance:
    161 to 165 mm (6.339 to 6.496 in.)


12. INSTALL FRONT DRIVE SHAFT DAMPER CLAMP LH (for Automatic Transaxle)

C127651E01
  1. Hold the front drive shaft lightly in a soft vise.

  1. Install the drive shaft damper clamp to the damper.

    NOTICE:
    Be sure to install the clamp in the correct position.

  1. One touch type:

    1. Using a screwdriver, install the drive shaft damper clamp, as shown in the illustration.

  1. Claw engagement type:

    1. Using needle-nose pliers, install the drive shaft damper clamp, as shown in the illustration.


13. INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY LH
  1. Wrap the spline of the outboard joint shaft with vinyl tape to prevent the boots from being damaged.

  1. Install new parts to the outboard joint shaft in the following order.

    1. Inboard joint boot clamp

    2. No. 2 inboard joint boot clamp

    3. Inboard joint clamp

  1. C127694E02
    Place the beveled side of the tripod axial spline toward the outboard joint.

  1. Align the matchmarks placed before removal.

  1. Using a brass bar and hammer, tap the tripod joint onto the drive shaft.

    NOTICE:
    1. Do not tap the rollers.
    2. Be sure to install the tripod joint in the correct direction.

  1. Pack the inboard joint shaft and boot with grease from the boot kit.

    Standard grease capacity:
    175 to 185 g (6.2 to 6.5 oz.)

  1. C127695
    Using a snap ring expander, install a new shaft snap ring.

  1. Align the matchmarks, and install the inboard joint to the outboard joint shaft.


14. INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


15. INSTALL FRONT AXLE INBOARD JOINT BOOT
  1. Install the inboard joint boot to the inboard joint.


16. INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP LH

C127696E01
  1. One touch type:

    1. Using a screwdriver, install the inboard joint boot clamp, as shown in the illustration.

      NOTICE:
      Be careful not to damage the boot.

  1. Claw engagement type:

    1. Using needle-nose pliers, install the inboard joint boot clamp, as shown in the illustration.

      NOTICE:
      Be careful not to damage the boot.


17. INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP RH

HINT:
Use the same procedures described for the LH side.


18. INSTALL FRONT AXLE INBOARD JOINT BOOT NO. 2 CLAMP LH

C127697E01
  1. One touch type:

    1. Using a screwdriver, install the inboard joint boot clamp, as shown in the illustration.

      NOTICE:
      Be careful not to damage the boot.

  1. Claw engagement type:

    1. Using needle-nose pliers, install the inboard joint boot clamp, as shown in the illustration.

      NOTICE:
      Be careful not to damage the boot.


19. INSTALL FRONT AXLE INBOARD JOINT BOOT NO. 2 CLAMP RH

HINT:
Use the same procedures described for the LH side.


20. INSPECT FRONT DRIVE SHAFT

C127698
  1. Check that there is no severe play in the radial direction of the outboard joint.

  1. Check that the inboard joint slides smoothly in the thrust direction.

  1. Check that there is no severe play in the radial direction of the inboard joint.

  1. C127699E01
    Check the boots for damage.

    NOTICE:
    Keep the drive shaft assembly level during inspection.

    HINT:
    For dimension (A), refer to the following values.

    Standard reference value:
    Item
    Drive shaft LH (Dimension)
    Drive shaft RH (Dimension)
    2AZ-FE 4A/T
    585.2 mm (23.039 in.)
    902.0 mm (35.512 in.)
    2AZ-FE 5M/T
    583.6 mm (22.976 in.)
    906.4 mm (35.685 in.)

← DISASSEMBLY (from Nov 2005)INSTALLATION (Nov 2005 – Dec 2006) →