2005-2008 RAV4 · Service Manual DRIVE LINE

INSTALLATION

Removal / installation · Vehicles built Nov 2005 – Dec 2006

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007


1. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH

C127700
  1. Coat the spline of the inboard joint shaft with gear oil.

  1. Using a brass bar and hammer, align the shaft splines in the drive shaft.

    NOTICE:
    1. Set the snap ring with the opening side facing downwards.
    2. Be careful not to damage the oil seal, boot and dust cover.


2. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH
  1. Coat the spline of the inboard joint shaft with gear oil.

  1. C127638
    Align the shaft spline and install the drive shaft with 2 bolts.

    Torque:
    63.7 N*m{ 650 kgf*cm , 47 ft.*lbf }

    NOTICE:
    Do not damage the oil seal, boot and dust cover.


3. CONNECT STEERING KNUCKLE WITH AXLE HUB LH
  1. Align the shaft splines in the drive shaft to the steering knuckle with axle hub.


4. CONNECT STEERING KNUCKLE WITH AXLE HUB RH

HINT:
Use the same procedures described for the LH side.


5. CONNECT FRONT SUSPENSION NO. 1 LOWER ARM SUB-ASSEMBLY LH

C127531
  1. Remove the bolt and 2 nuts.

  1. Disconnect the lower arm from the ball joint.


6. CONNECT FRONT SUSPENSION NO. 1 LOWER ARM SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


7. INSTALL FRONT STABILIZER LINK ASSEMBLY LH
  1. Install the link with the 2 nuts.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }


8. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


9. CONNECT TIE ROD END SUB-ASSEMBLY LH

C132132
  1. Connect the tie rod end onto the steering knuckle with the castle nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

    NOTICE:
    If the holes for the clip are not aligned, tighten the nut up to 60° further.

  1. Install a new cotter pin.


10. CONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


11. INSTALL FRONT SPEED SENSOR LH

NOTICE:
To prevent interference with other parts, do not twist the sensor wire's painted line areas when installing it.

  1. C127961E01
    Set the sensor body to the knuckle, and then install the sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    1. Keep the sensor tip and sensor installation hole free from foreign matter.
    2. Firmly insert the sensor body into the knuckle before tightening the bolt.
    3. After installing the sensor to the knuckle, make sure that there is no clearance between the sensor stay and knuckle. Also make sure that no foreign matter is stuck between the parts.
    4. To prevent interference between the sensor and magnetic rotor, do not rotate the sensor body during or after the insertion of the sensor body to the knuckle.

  1. Install the sensor clamp and sensor clip as follows.

    C127962E02

    1. Set the flexible hose clamp on the flexible hose bracket.

    2. Simultaneously perform the following: 1) hang the hook part of the sensor clamp (labeled A) on the part of the flexible hose bracket (labeled C); and 2) insert the hook part of the sensor clamp (labeled B) to the part of the flexible hose bracket (labeled D).

      NOTICE:
      Do not twist the sensor wire when installing the clamp.

    3. Tighten together the sensor clamp and the flexible hose clamp to the flexible hose bracket with the bolt (labeled E).

      Torque:
      18.5 N*m{ 189 kgf*cm , 14 ft.*lbf }

    4. Insert the sensor clip (labeled F) into the hole on the absorber lower bracket.

  1. C127963E02
    Install the sensor clamp, and sensor clip as follows.

    1. Set the sensor clamp (labeled G) on the side member, and then tighten it with the bolt (labeled H).

      Torque:
      8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

      NOTICE:
      Do not twist the sensor wire when installing the clamp.

    2. Insert the sensor clip (labeled I) into the hole on the apron.

  1. C127964E01
    Connect the sensor connector.


12. INSTALL FRONT SPEED SENSOR RH

HINT:
Use the same procedures described for the LH side.


13. INSTALL FRONT AXLE HUB NUT
  1. Install a new hub nut.

    Torque:
    216 N*m{ 2,203 kgf*cm , 159 ft.*lbf } for φ 26
    292 N*m{ 2,978 kgf*cm , 215 ft.*lbf } for φ 30

  1. C129484
    Using a chisel and hammer, stake the hub nut.


14. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }


15. ADD AUTOMATIC TRANSAXLE FLUID

Fluid type:
Toyota Genuine ATF WS


16. ADD TRANSAXLE OIL
  1. Stop the vehicle in a level place.

  1. Remove the transaxle filler plug and gasket.

  1. D025304E21
    Check that the oil level is between 0 to 5 mm (0 to 0.20 in.) from the bottom lip of the filler plug opening. If the result is not as specified, add transaxle oil.

    Oil grade:
    GL-4

    Viscosity:
    SAE 75W

    Standard capacity:
    2.5 liters (2.6 US qts, 2.2 Imp. qts)

    NOTICE:
    1. Too much or too little oil will lead to transaxle problems.
    2. After adjusting the oil level, drive the vehicle and check the oil level again.

  1. Check for oil leakage if the oil level is low.

  1. Install the transaxle filler plug and a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


17. CHECK FOR AUTOMATIC TRANSAXLE OIL LEAKAGE

18. CHECK FOR TRANSAXLE OIL LEAKAGE

19. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
  1. Inspect and adjust the front wheel alignment (Click here).

← REASSEMBLY (from Nov 2005)INSTALLATION (Jan 2007 – Jul 2007) →