2005-2008 RAV4 · Service Manual DRIVE LINE

REMOVAL

Removal / installation · Vehicles built Nov 2005 – Dec 2006

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007


1. REMOVE FRONT WHEEL

2. DRAIN AUTOMATIC TRANSAXLE FLUID (for 1AZ-FE, 2AZ-FE)
  1. Drain the automatic transaxle fluid for U140F (Click here).

  1. Drain the automatic transaxle fluid for U241E (Click here).


3. DRAIN TRANSAXLE OIL
  1. Drain the transaxle oil for E352F/E359F (Click here).

  1. Drain the transaxle oil for E352 (Click here).

  1. Drain the transaxle oil for EA64F (Click here).


4. REMOVE FRONT AXLE HUB NUT

C129483E01
  1. Using SST and a hammer, unstake the staked part of the nut.

    SST
    09930-00010  

    NOTICE:
    Loosen the staked part of the nut completely, otherwise the screw of the drive shaft may be damaged.

  1. While applying the brakes, remove the lock axle hub nut.


5. REMOVE FRONT SPEED SENSOR LH

  1. C127964E01
    Disconnect the sensor connector.

  1. C127963E01
    Remove the sensor clip (labeled A), bolt (labeled B) and sensor clamp (labeled C).

  1. Remove the sensor clip (labeled D), bolt (labeled E) and sensor clamp (labeled F).

    C127962E01

  1. C127961E01
    Remove the bolt and sensor body from the knuckle.

    NOTICE:
    Keep the sensor tip and sensor installation hole free from foreign matter.


6. REMOVE FRONT SPEED SENSOR RH

HINT:
Use the same procedures described for the LH side.


7. DISCONNECT FRONT DISC BRAKE CYLINDER ASSEMBLY LH

C127058
  1. Remove the 2 bolts and cylinder.


8. DISCONNECT FRONT DISC BRAKE CYLINDER ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


9. REMOVE FRONT STABILIZER LINK ASSEMBLY LH

  1. C127528
    Remove the 2 nuts and stabilizer link.


10. REMOVE FRONT STABILIZER LINK ASSEMBLY RH

11. DISCONNECT FRONT SUSPENSION LOWER NO. 1 ARM SUB-ASSEMBLY LH

C127531
  1. Remove the bolt and 2 nuts.

  1. Disconnect the lower arm from the ball joint.


12. DISCONNECT FRONT SUSPENSION LOWER NO. 1 ARM SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


13. DISCONNECT STEERING KNUCKLE WITH AXLE HUB LH

C129488E01
  1. Put matchmarks on the drive shaft and axle hub.

    NOTICE:
    Do not punch the marks.

  1. Using a plastic-faced hammer, disconnect the steering knuckle with axle hub.

    NOTICE:
    Be careful not to damage the boot and speed sensor rotor.
    1. Do not excessively push out the drive shaft from the axle assembly.


14. DISCONNECT STEERING KNUCKLE WITH AXLE HUB RH

HINT:
Use the same procedures described for the LH side.


15. DISCONNECT TIE ROD END SUB-ASSEMBLY LH
  1. Remove the cotter pin and castle nut.

  1. C132680E01
    Using SST, disconnect the tie rod end from the steering knuckle.

    NOTICE:
    Do not damage the tie rod end dust cover.

    SST
    09628-62011  


16. DISCONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


17. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH

C127631E01
  1. Using SST, remove the front drive shaft.

    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    1. Be careful not to damage the transaxle case oil seal, inboard joint boot and drive shaft dust cover.
    2. Be careful not to drop the drive shaft assembly.


18. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

C127633E01
  1. Using a brass bar and hammer, set the brass bar against position (1) as shown in the illustration and remove the drive shaft.

    NOTICE:
    1. Do not damage the oil seal.
    2. Do not damage the drive shaft boot.
    3. Do not allow the drive shaft to fall off.

  1. C127640
    Squeeze the ends of the snap ring, and remove the snap ring from the bearing bracket.

  1. Remove the bearing bracket bolt and remove the front drive shaft from the bearing bracket.

    NOTICE:
    1. Do not damage the oil seal.
    2. Do not damage the boot.
    3. Do not allow the drive shaft to fall off.

    HINT:
    If the connection is stiff, use a brass bar and hammer to lightly tap the edge of the inboard joint assembly RH and remove it.


19. FIX FRONT AXLE ASSEMBLY

C129482E01

NOTICE:
The hub bearing could be damaged if it is subjected to the vehicle weight, such as when moving the vehicle with the drive shaft removed. Therefore, if it is absolutely necessary to place the vehicle weight on the hub bearing, first support it with SST.

SST
09608-16042   (09608-02021, 09608-02041)
← COMPONENTS (from Aug 2007)REMOVAL (Jan 2007 – Jul 2007) →