2005-2008 RAV4 · Service Manual SUSPENSION & AXLE

INSTALLATION

Removal / installation · Vehicles built Jan 2007 – Jul 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007

HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.


1. TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

C129667
  1. Temporarily install the No. 2 suspension arm with the bolt and nut to the suspension member.


2. INSTALL REAR COIL SPRING INSULATOR LOWER LH
  1. Install the insulator lower to the suspension No. 2 arm.


3. INSTALL REAR COIL SPRING LH
  1. Install the coil spring to the suspension No. 2 arm.


4. INSTALL REAR COIL SPRING INSULATOR UPPER LH
  1. Align the stopper part of the insulator upper with the coil spring tip, and install the insulator upper.


5. INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

C129676E01
  1. Slowly raise the jack, and install the No. 2 suspension arm to the axle carrier.

    NOTICE:
    Install the arm so that the coil spring's distinguishing mark is on the outer side of the vehicle.


6. INSTALL REAR STABILIZER LINK ASSEMBLY LH

  1. C127558
    Install the stabilizer link with the 2 nuts.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf } for stabilizer bar
    30 N*m{ 306 kgf*cm , 22 ft.*lbf } for suspension No. 2 arm


7. CONNECT SKID CONTROL SENSOR WIRE (for 2WD)

NOTICE:
To prevent interference with other parts, do not twist the sensor wire's painted line areas when installing it.

  1. C127966E02
    Connect the skid control sensor wire connector (labeled A) to the speed sensor.

  1. Install the sensor clamp (labeled B) with the bolt (labeled C).

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    Do not twist the sensor wire when installing the clamp.

  1. C127967E02
    Install the sensor clamps (labeled D) with the 2 nuts (labeled E).

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    NOTICE:
    Do not twist the sensor wire when installing the clamps.

  1. Install the sensor clamp (labeled F) with the bolt (labeled G).

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    Do not twist the sensor wire when installing the clamp.

  1. C127968E01
    Insert the connector and grommet to the inside of the vehicle through the passage hole in the wheel house.

    NOTICE:
    Make sure the grommet's band clamp remains on the outside of the vehicle.

  1. C127969E01
    Hold the grommet and pull it from the inside of the vehicle to the outside of the vehicle. Then fix it in place so that it is not tilted.

    NOTICE:
    1. When pulling out the grommet, do not grip the sensor wire.
    2. Fix the grommet in place within the range shown in the illustration.

  1. C127328
    Connect the skid control sensor wire connector.


8. CONNECT REAR SPEED SENSOR LH (for 4WD)

NOTICE:
To prevent interference with other parts, do not twist the sensor wire's painted line areas when installing it.

  1. C127972E02
    Install the sensor (labeled A) with the bolt (labeled B).

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    1. Keep the sensor tip and sensor installation hole free from foreign matter.
    2. To prevent interference with the bearing rotor, do not rotate the sensor body when inserting the sensor body or after inserting the sensor body.

  1. Install the sensor clamp (labeled C) with the nut (labeled D).

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. C127973E02
    Install the sensor clamps (labeled E) with the 2 nuts (labeled F).

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    NOTICE:
    Do not twist the sensor wire when installing the clamps.

  1. Install the sensor clamp (labeled G) with the bolt (labeled H).

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    Do not twist the sensor wire when installing the clamp.

  1. C127968E01
    Insert the connector and grommet to the inside of the vehicle through the passage hole in the wheel house.

    NOTICE:
    Make sure the grommet's band clamp remains on the outside of the vehicle.

  1. C127969E01
    Hold the grommet and pull it from the inside of the vehicle to the outside of the vehicle. Then fix it in place so that it is not tilted.

    NOTICE:
    1. When pulling out the grommet, do not grip the sensor wire.
    2. Fix the grommet in place within the range shown in the illustration.

  1. C127328
    Connect the speed sensor connector.


9. CONNECT NO. 2 PARKING BRAKE CABLE ASSEMBLY

  1. Connect the cable to the backing plate and parking brake shoe lever.

    1. Pass the cable through the backing plate, and then connect the cable to the lever.

    2. Install the cable to the backing plate with the bolt.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


      C127323E01

  1. Install the clamp and clamp bolt (labeled F) to the trailing arm.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

    NOTICE:
    Securely install the clamp.

  1. Install the clamp and clamp bolt (labeled E) to the rear suspension crossmember.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

    NOTICE:
    Securely install the clamp.

  1. Install the clamp and clamp bolt (labeled D) to the crossmember.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

    NOTICE:
    Securely install the clamp.

  1. Install the clamp and clamp bolt (labeled C) to the body.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

    NOTICE:
    Securely install the clamp.

  1. Install the casing cap and casing cap bolt (labeled B) to the body.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

    NOTICE:
    Securely install the casing cap.

  1. Install the cable clamp (labeled A) to the body.

    NOTICE:
    Securely install the clamp.


10. INSTALL REAR WHEEL
  1. Install the wheel.

    Torque:
    103 N*m{ 1050 kgf*cm , 76 ft.*lbf }


11. STABILIZE SUSPENSION
  1. Lower the vehicle.

  1. Press down on the vehicle several times to stabilize the suspension.


12. TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH
  1. Install the 2 nuts and 2 bolts.

    Torque:
    90 N*m{ 918 kgf*cm , 66 ft.*lbf }

    NOTICE:
    Do not tighten the nuts.


13. INSPECT AND ADJUST REAR WHEEL ALIGNMENT
  1. Inspect and adjust the rear wheel alignment (Click here).

← INSTALLATION (Nov 2005 – Dec 2006)INSTALLATION (from Aug 2007) →