2005-2008 RAV4 · Service Manual SUSPENSION & AXLE

ADJUSTMENT

Removal / installation · Vehicles built Nov 2005 – Jul 2007

Versions by build date: Nov 2005 – Jul 2007 from Aug 2007


1. INSPECT TIRE
  1. Inspect the tire (Click here).


2. MEASURE VEHICLE HEIGHT
  1. Measure the vehicle height (Click here).


3. INSPECT TOE-IN

SA03213E04

Standard toe-in:
Item
Specified Condition
Toe-in
(total)
A + B: 0°11' +-10' (0.18° +-0.17°)
C - D: 2.3 +-1 mm (0.09 +-0.04 in.)

  1. If the toe-in is not within the specified range, inspect the suspension parts and replace them if necessary.

4. ADJUST TOE-IN

  1. C132369
    Measure the length of the left and right rear No. 1 suspension arms.

    Standard difference:
    1.0 mm (0.0394 in.) or less

  1. C132370E01
    Loosen the 2 lock nuts of the adjusting tube.

    HINT:
    Loosen the 2 lock nuts of the adjusting tube on the other side using the same procedure.

  1. If the difference between the length of the left and right rear No. 1 suspension arms is not within the specification, adjust the value to within the specification using the method below.

    1. If the toe-in value deviates towards the inside, turn the adjusting tube of the shorter No. 1 suspension arm assembly in the direction which increases arm length until the difference between the left and right suspension arms is within the specification.

    2. If the toe-in value deviates towards the outside, turn the adjusting tube of the longer No. 1 suspension arm assembly in the direction which decreases arm length until the difference between the left and right suspension arms is within the specification.

    3. Measure the toe-in again.

  1. Turn the left and right adjusting tubes in the same direction by the same amount to adjust the toe-in.

    Adjustment Value:
    2.3 +-1.0 mm (0.0905 +-0.0394 in.)

    HINT:
    1. When the adjusting tube of the rear No. 1 suspension arm assembly LH is turned one revolution in the direction of A in the illustration, the toe-in changes to the inside by approximately 3.7 mm (0.146 in.)
    2. When the adjusting tube of the rear No. 1 suspension arm assembly LH is turned one revolution in the direction of B in the illustration, the toe-in changes to the outside by approximately 3.7 mm (0.146 in.).

  1. Tighten the lock nuts of the adjusting tube.

    Torque:
    56 N*m{ 571 kgf*cm , 41 ft.*lbf }

    NOTICE:
    Make sure to hold the adjusting tube at the width across flats when tightening the nuts.

    HINT:
    Tighten the 2 lock nuts of the adjusting tube on the other side using the same procedure.


5. INSPECT CAMBER
  1. Install the camber-caster-kingpin gauge or set the vehicle on the wheel alignment tester.

  1. Inspect the camber.

    Standard camber:
    Item
    Specified Condition
    Camber
    Right-left error
    *Tire Size: 215/70R16
    0°58' +-45' (0.97° +-0.75°)
    45' (0.75°) or less
    Tire Size: 225/65R17
    Tire Size: 235/55R18
    -1°07' +-45' (-1.12° +-0.75°)
    45' (0.75°) or less
    Australia
    -0°52' +-45' (0.87° +-0.75°)
    45' (0.75°) or less

    1. *: Europe only

    HINT:
    Camber is not adjustable. If the measurement is not within the specified range, inspect the suspension parts for damage and/or wear, and replace them if necessary.

← ADJUSTMENT (from Aug 2007)ADJUSTMENT (from Aug 2007) →