2005-2008 RAV4 · Service Manual BODY

DATA LIST / ACTIVE TEST

System information · Vehicles built from Nov 2005


READ DATA LIST

HINT:
Using the intelligent tester's Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch on (IG).

  3. Read the Data List.

    Power window regulator motor (Power window ECU) 
    Item
    Measurement Item / Display (Range)
    Normal Condition
    Diagnosis Note
    D P/W Auto Switch
    Driver side power window auto UP / DOWN switch signal / ON or OFF
    ON: Driver side power window AUTO switch operates
    OFF: Driver side power window AUTO switch does not operate
    -
    D P/W Up Switch
    Driver side power window manual UP switch signal / ON or OFF
    ON: Driver side power window UP switch operates
    OFF: Driver side power window UP switch does not operate
    -
    D P/W Down Switch
    Driver side power window manual DOWN switch signal / ON or OFF
    ON: Driver side power window DOWN switch operates
    OFF: Driver side power window DOWN switch does not operate
    -
    Glass Pos Info
    Glass position signal
    min.: 128 hex
    max.: approx. 390 hex (front side)
    max.: approx. 354 hex (rear side)
    Closed: 128 hex
    Open: approx. 390 hex (front side)
    Open: approx. 354 hex (rear side)
    -
    Glass Pos - 1/4
    Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open position / OK or CAUTION
    OK: Margin is sufficient during manual UP operation
    CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.
    -
    Glass Pos - 2/4
    Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open position / OK or CAUTION
    OK: Margin is sufficient during manual UP operation
    CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.
    -
    Glass Pos - 3/4
    Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open position / OK or CAUTION
    OK: Margin is sufficient during manual UP operation
    CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.
    -
    Glass Pos - Open
    Margin for jam protection triggering force of window glass within range of 3/4 to fully open position / OK or CAUTION
    OK: Margin is sufficient during manual UP operation
    CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.
    -
    Power window regulator master switch assembly 
    Item
    Measurement Item / Display (Range)
    Normal Condition
    Diagnosis Note
    D P/W Auto Switch
    Driver side power window auto UP / DOWN switch signal / ON or OFF
    ON: Driver side power window AUTO switch operates
    OFF: Driver side power window AUTO switch does not operate
    -
    Main body ECU 
    Item
    Measurement Item / Display (Range)
    Normal Condition
    Diagnosis Note
    Communication D-Door Motor
    Connection status between power window regulator motor assembly (driver door) and main body ECU / OK or STOP
    OK: Connection
    Stop: No connection
    -
    D Door Courtesy Switch
    Driver side door courtesy switch signal / ON or OFF
    ON: Driver door open
    OFF: Driver door closed
    -
    P Door Courtesy Switch
    Front passenger side door courtesy switch signal / ON or OFF
    ON: Front passenger door open
    OFF: Front passenger door close
    -


PERFORM ACTIVE TEST

CAUTION:
Be careful to avoid injuries as this test causes vehicle parts to move.

HINT:
Performing the intelligent tester's Active Test allows relay, VSV, actuator, and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time. The Data List can be displayed during the Active Test.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch on (IG).

  3. Performing the Active Test by following the prompts on the tester screen.

    Power window regulator motor (Power window ECU) 
    Item
    Test Details
    Diagnostic Note
    Power window
    OFF / UP / DOWN (OFF)
    -
    Main body ECU 
    Item
    Test Details
    Diagnostic Note
    IG OFF P/W
    ON / OFF
    -

← FAIL-SAFE CHART (from Nov 2005)DIAGNOSTIC TROUBLE CODE CHART (from Nov 2005) →