2005-2008 RAV4 · Service Manual HEATER & AIR CONDITIONING SYSTEM

INSTALLATION

Removal / installation · Vehicles built Nov 2005 – Dec 2006

Versions by build date: Nov 2005 – Dec 2006 from Jan 2007


1. INSTALL WATER PIPE AND HOSE SUB-ASSEMBLY
  1. Install the water pipe and hose with the nut and bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }

  1. Connect the heater hoses.

    H102054


2. INSTALL HEATER PUMP ASSEMBLY
  1. Install the heater pump with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }

  1. Connect the fuel hoses.

    H102053


3. INSTALL HEATER ASSEMBLY
  1. Install the heater with the 2 bolts and 2 nuts.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }

  1. Connect the fuel hose.

  1. Connect the heater hoses.

  1. Connect the connectors.

    H102055


4. INSTALL EXHAUST PIPE SUB-ASSEMBLY

  1. Install the exhaust pipe with the 2 nuts and bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }


    C128791


5. ADD ENGINE COOLANT
  1. Tighten the radiator drain cock plug by hand.

  1. Tighten the cylinder block drain cock plug.

    Torque:
    12.7 N*m{ 130 kgf*cm , 10 ft.*lbf }

  1. Add TOYOTA Super Long Life Coolant (SLLC) to the radiator reservoir filler opening.

  1. A126841E01
    Continue adding TOYOTA SLLC until it is filled to the B line.

    HINT:
    The B line is the lower edge of the inner wall of the filler neck.

    Standard capacity:
    Item
    Specified Condition
    w/o Combustion Type Power Heater
    7.3 liters
    (7.7 US qts, 6.4 Imp. qts)
    w/ Combustion Type Power Heater
    7.7 liters
    (8.1 US qts, 6.8 Imp. qts)

    HINT:
    TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level drops below the B line, add TOYOTA SLLC to the B line.

  1. Install the radiator reservoir cap.

  1. Start the engine, and warm it up until the cooling fan operates.

    1. Set the air conditioning as follows while warming up the engine.

      Item
      Specified Condition
      Manual Air Conditioning System
      Fan speed - Any setting except "OFF"
      Temperature - Toward WARM
      Air conditioning switch "OFF"
      Automatic Air Conditioning System
      Temperature - Toward MAX
      Air conditioning switch "OFF"

    2. Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.

      NOTICE:
      1. Make sure that the radiator reservoir still has some coolant in it.
      2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
      3. If there is not enough coolant, the engine may burn out or overheat.
      4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the B line.
      5. Until the coolant level has stabilized, run the engine at 2,000 rpm.

  1. Press the inlet and outlet radiator hoses several times by hand to bleed air.

    CAUTION:
    When pressing the radiator hoses:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the radiator fan.

  1. Stop the engine and wait until the coolant cools down to ambient temperature.

  1. A126840
    Check that the coolant level is between the FULL and LOW line.
    If the coolant level is below the LOW line, repeat all of the procedures above.
    If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW line.


6. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

7. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).


8. WARM UP ENGINE

9. CHECK HEATER SYSTEM

B135366E02
  1. After the heater switch is turned ON and 20 seconds have passed, touch the part of the fuel hose labeled A in the illustration and check that the hose is vibrating.

← REMOVAL (from Nov 2005)INSTALLATION (from Jan 2007) →