REMOVAL
Removal / installation · Vehicles built Nov 2005 – Dec 2006
Versions by build date: Nov 2005 – Dec 2006 from Jan 2007
| 1.
REMOVE PACKAGE TRAY TRIM POCKET SUB-ASSEMBLY |
|
| 2.
REMOVE TONNEAU COVER ASSEMBLY |
|
| 3.
REMOVE REAR FLOOR NO. 1 BOARD |
|
| 4.
REMOVE DECK BOARD ASSEMBLY |
|
| 5.
REMOVE REAR FLOOR NO. 3 BOARD |
|
| 6.
REMOVE REAR FLOOR NO. 2 BOARD |
|
| 7.
REMOVE JACK CARRIER ASSEMBLY (for Short Body)
|
 |
Using a clip remover, remove the 7 clips and remove the jack carrier.
| 8.
REMOVE REAR FLOOR NO. 1 MAT SUPPORT SIDE PLATE (for Short Body)
|
 |
Remove the 4 screws.
Using a clip remover, detach the 7 clips and remove the plate.
| 9.
REMOVE REAR FLOOR NO. 1 MAT SUPPORT SIDE PLATE (for Long Body)
|
 |
Remove the 4 screws.
Using a clip remover, detach the 7 clips and remove the plate.
| 10.
REMOVE BACK DOOR WEATHERSTRIP |
|
| 11.
REMOVE REAR FLOOR FINISH PLATE (for Short Body)
|
 |
- Using a clip remover, detach the 6 clips and remove the finish plate.
| 12.
REMOVE REAR FLOOR FINISH PLATE (for Long Body)
|
 |
Using a clip remover, detach the 6 clips.
Detach the 2 claws and remove the finish plate.
| 13.
REMOVE RECLINING REMOTE CONTROL LEVER BEZEL RH |
 |
- Using a screwdriver, detach the 6 claws and remove the bezel.
- HINT:
- Tape the screwdriver tip before use.
| 14.
REMOVE TETHER ANCHOR BRACKET SUB-ASSEMBLY (for Long Body)
|
 |
- Remove the bolt and tether anchor bracket.
| 15.
REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR COVER (for Short Body)
|
 |
Using a screwdriver, detach the 4 claws and remove the cover.
- HINT:
- Tape the screwdriver tip before use.
| 16.
REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR BRACKET (for Short Body)
|
 |
- Remove the bolt, 2 washers, collar and bracket.
| 17.
REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH (for Short Body)
|
 |
- Disconnect the rear No. 1 seat belt's floor anchor.
Remove the anchor cover.
Remove the bolt and disconnect the floor anchor.
- Remove the bolt and 2 screws.
Using a screwdriver, detach the 5 claws.
- HINT:
- Tape the screwdriver tip before use.
Using a clip remover, detach the 5 clips and remove the trim board.
Remove the belt hanger.
| 18.
REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH (for Long Body)
|
 |
- Disconnect the rear No.1 seat outer belt's floor anchor.
Remove the anchor cover.
Remove the bolt and disconnect the floor anchor.
- Remove the 2 screws and 2 bolts.
Using a screwdriver, detach the 5 claws.
- HINT:
- Tape the screwdriver tip before use.
Using a clip remover, detach the 4 clips and remove the trim board.
Remove the belt hanger.
| 19.
REMOVE RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY RH |
 |
- Remove the 2 bolts and lever.
Disconnect the rear No. 1 seat lock cable from the lever.
| 20.
REMOVE REAR NO. 3 SEAT LEG SIDE COVER |
 |
- Using a screwdriver, detach the 4 claws and remove the side cover.
- HINT:
- Tape the screwdriver tip before use.
| 21.
REMOVE REAR NO. 2 SEAT LEG SIDE COVER |
 |
- Using a screwdriver, detach the 3 claws and clip, remove the side cover.
- HINT:
- Tape the screwdriver tip before use.
| 22.
REMOVE REAR SEAT LEG COVER |
 |
- Using a screwdriver, detach the 8 claws and remove the 2 leg covers.
- HINT:
- Tape the screwdriver tip before use.
| 23.
REMOVE REAR NO. 1 SEAT LOCK CABLE ASSEMBLY |
 |
Disconnect the lock cable from the seat.
Raise the adjuster's lock piece to release the lock.


- Slide the seat forward and tilt the seatback forward.
- Remove the seat's cap from the connector case.
- Pull the seat's cap toward the outside of the vehicle. Then remove the cable from the connector case's slit.
- Remove the body's cap from the connector case.
Detach the clamps and remove the lock cable.


| 24.
REMOVE REAR NO. 1 SEAT ASSEMBLY RH |
 |
Lift up the seat track adjusting handle and move the seat to the rearmost position.
- Remove the 2 bolts on the front side of the seat.
Lift up the seat track adjusting handle and move the seat to the foremost position.
- Remove the 3 bolts on the rear side of the seat.
Fully tilt the seatback forward. Then remove the seat.
- NOTICE:
- Be careful not to damage the vehicle body,