DISASSEMBLY
Removal / installation · Vehicles built from Jan 2007
Versions by build date: Nov 2005 – Dec 2006 from Jan 2007
- CAUTION:
- Wear protective gloves. Sharp areas on the seatback frame, seat cushion frame and reclining adjuster may injure your hands.
| 1.
REMOVE REAR SEAT HEADREST ASSEMBLY |
|
| 2.
REMOVE REAR SEAT CENTER HEADREST ASSEMBLY |
|
| 3.
REMOVE CENTER ARMREST HINGE COVER RH |
 |
Return the seatback to the upright position.
- Remove the 2 rear seatback lock hooks.
Fold back the seatback cover until the screws are visible, and remove the 2 screws.
Detach the claw and remove the hinge cover.
| 4.
REMOVE CENTER ARMREST HINGE COVER LH |
 |
- Using a screwdriver, detach the 4 claws and remove the hinge cover.
- HINT:
- Tape the screwdriver tip before use.
| 5.
REMOVE REAR SEAT CENTER ARMREST ASSEMBLY |
 |
- Remove the 2 nuts and armrest.
| 6.
REMOVE REAR SEAT CENTER ARMREST COVER |
 |
- Detach the 2 clips.
- Pull the armrest cover in the direction indicated by the arrow in the illustration to detach the 2 claws. Then remove the armrest cover.
| 7.
REMOVE REAR NO. 1 SEAT ARMREST ASSEMBLY LH |
 |
- Remove the 2 nuts and armrest.
| 8.
REMOVE REAR NO. 3 SEAT CUSHION HINGE COVER |
 |
- Using a screwdriver, detach the 6 claws and remove the hinge cover.
- HINT:
- Tape the screwdriver tip before use.
| 9.
REMOVE REAR SEAT CUSHION LOWER HINGE COVER LH |
 |
- Using a screwdriver, detach the 5 claws and remove the hinge cover.
- HINT:
- Tape the screwdriver tip before use.
| 10.
REMOVE REAR SEAT INNER BELT ASSEMBLY RH
|
 |
Remove the bolt and the seat belt.
| 11.
REMOVE REAR NO. 1 SEAT CUSHION ASSEMBLY LH |
 |
- Disconnect the rubber band of the seatback cover from the seat cushion frame.
Remove the 2 bolts.
- Remove the 2 bolts, 2 bushes and cushion.
| 12.
REMOVE REAR NO. 1 SEAT CUSHION COVER |
 |
- Detach the 2 hooks.
- Remove the 29 hog rings and seat cushion cover (with pad) from the seat cushion frame.
- Remove the 3 hog rings and seat cushion cover from the seat cushion pad.
| 13.
REMOVE REAR SEAT REAR BRACKET COVER LH |
 |
- Open the lower part of the seatback cover. Then remove the 2 screws.
Using a screwdriver, detach the 4 clips and remove the bracket cover.
| 14.
REMOVE REAR SEAT CUSHION MOULDING LH |
 |
- Remove the screw.
Detach the 2 claws and remove the moulding.
| 15.
REMOVE REAR SEAT CUSHION REAR MOULDING LH |
 |
- Remove the screw.
Detach the claw and remove the moulding.
| 16.
REMOVE REAR SEAT RECLINING RELEASE LEVER |
 |
- Pull the reclining control lever to reveal the 2 screws. Then remove the 2 screws and cover.
- Using a screwdriver, detach the claw and remove the release lever.
- HINT:
- Tape the screwdriver tip before use.
| 17.
REMOVE REAR SEATBACK LOCK CONTROL LEVER BASE LH |
 |
- Remove the screw.
Using a screwdriver, detach the 2 claws and remove the lever base.
- HINT:
- Tape the screwdriver tip before use.
| 18.
REMOVE REAR NO. 1 SEATBACK ASSEMBLY LH |
 |
- Detach the 2 clamps and disconnect the cable from the reclining adjuster.
- Remove the 5 bolts and seatback.
| 19.
REMOVE REAR SEAT LAP TYPE BELT ASSEMBLY CENTER LH
|
 |
Remove the bolt and the seat belt.
| 20.
REMOVE REAR SEATBACK PROTECTOR |
 |
- Using a clip remover, detach the 2 clips and open the fastening tape.
- NOTICE:
- If clips are damaged during removal, replace them.
- Detach the clip.
Remove the 2 nuts and protector.
| 21.
REMOVE REAR NO. 1 SEATBACK COVER |
 |
- Lift up the seatback cover and remove the 13 hog rings.
- Detach the 4 claws and remove the 2 headrest supports.
Remove the seatback cover (with pad) from the seatback frame.
- Remove the 3 hog rings and seatback cover from the seatback pad.
| 22.
REMOVE REAR SEAT COVER LH |
 |
- Remove the 2 screws.
Using a screwdriver, detach the 2 claws and remove the cover.
- HINT:
- Tape the screwdriver tip before use.
| 23.
REMOVE REAR SEATBACK COVER LH |
 |
- Remove the 2 screws.
Using a screwdriver, detach the 2 claws and remove the cover.
- HINT:
- Tape the screwdriver tip before use.