REASSEMBLY
Removal / installation · Vehicles built Nov 2005 – Dec 2006
Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007
- CAUTION:
- Wear protective gloves. Sharp areas on the seatback frame, seat cushion frame and reclining adjuster may injure your hands.
- HINT:
- A bolt without a torque specification is shown in the standard bolt chart (Click here).
| 1.
INSTALL REAR SEAT COVER LH |
 |
- Attach the 2 claws to install the cover.
Install the 2 screws.
| 2.
INSTALL REAR SEATBACK COVER LH |
 |
- Attach the 2 claws to install the cover.
Install the 2 screws.
| 3.
INSTALL REAR NO. 1 SEATBACK COVER |
 |
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, avoid wrinkling the cover.
- Using hog ring pliers, install the seatback cover to the seatback pad with 3 new hog rings.
Install the seatback cover (with pad) to the seatback frame.
- Attach the 4 claws to install the 2 headrest supports.
- Lift up the seatback cover and install the 13 hog rings.
| 4.
INSTALL REAR SEATBACK PROTECTOR |
 |
- Install the protector with the 2 nuts.
-
Torque:
- 20 N*m{
204 kgf*cm
, 15 ft.*lbf
}
Attach the clip.
- Attach the 2 clips and close the fastening tape.
| 5.
INSTALL REAR SEAT LAP TYPE BELT ASSEMBLY CENTER LH
|
 |
Install the belt with the bolt.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
| 6.
INSTALL REAR NO. 1 SEATBACK ASSEMBLY LH |
 |
- Install the seatback with the 5 bolts.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
- Attach the 2 clamps and connect the cable to the reclining adjuster.
| 7.
INSTALL REAR SEATBACK LOCK CONTROL LEVER BASE LH |
 |
- Attach the 2 claws to install the lever base.
Install the screw.
| 8.
INSTALL REAR SEAT RECLINING RELEASE LEVER |
 |
- Attach the claw to install the release lever.
- Install the cover with the 2 screws.
| 9.
INSTALL REAR SEAT CUSHION MOULDING LH |
 |
- Attach the 2 claws to install the moulding.
Install the screw.
| 10.
INSTALL REAR SEAT CUSHION REAR MOULDING LH |
 |
- Attach the claw to install the moulding.
Install the screw.
| 11.
INSTALL REAR SEAT REAR BRACKET COVER LH |
 |
- Open the lower part of the seatback cover. Then attach the 4 clips to install the bracket cover.
Install the 2 screws.
| 12.
INSTALL REAR NO. 1 SEAT CUSHION COVER |
 |
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, avoid wrinkling the cover.
- Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 3 new hog rings.
- Using hog ring pliers, install the seat cushion cover (with pad) to the seat cushion frame with 29 new hog rings.
- Attach the 2 hooks.
| 13.
INSTALL REAR NO. 1 SEAT CUSHION ASSEMBLY LH |
 |
- Install the cushion with the 2 bushes and 2 bolts.
-
Torque:
- 21 N*m{
214 kgf*cm
, 15 ft.*lbf
}
- Install the 2 bolts.
| 14.
INSTALL REAR SEAT INNER BELT ASSEMBLY RH
|
 |
Install the belt with the bolt.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
| 15.
INSTALL REAR SEAT CUSHION LOWER HINGE COVER LH |
 |
- Attach the 5 claws to install the hinge cover.
| 16.
INSTALL REAR NO. 3 SEAT CUSHION HINGE COVER |
 |
- Attach the 6 claws to install the hinge cover.
| 17.
INSTALL REAR NO. 1 SEAT ARMREST ASSEMBLY LH |
 |
- Install the armrest with the 2 nuts.
-
Torque:
- 32 N*m{
326 kgf*cm
, 24 ft.*lbf
}
| 18.
INSTALL REAR SEAT CENTER ARMREST COVER |
 |
- Push the armrest cover in the direction indicated by the arrow in the illustration to attach the 2 claws.
- Attach the 2 clips to install the armrest cover.
| 19.
INSTALL REAR SEAT CENTER ARMREST ASSEMBLY |
 |
- Install the armrest with the 2 nuts.
-
Torque:
- 32 N*m{
326 kgf*cm
, 24 ft.*lbf
}
| 20.
INSTALL CENTER ARMREST HINGE COVER LH |
 |
- Attach the 4 claws to install the hinge cover.
| 21.
INSTALL CENTER ARMREST HINGE COVER RH |
 |
Pass the seat lock release strap through the hole in the hinge cover.
Attach the claw to install the hinge cover.
- Install the 2 screws and 2 rear seatback lock hooks.
| 22.
INSTALL REAR SEAT CENTER HEADREST ASSEMBLY |
|
| 23.
INSTALL REAR SEAT HEADREST ASSEMBLY |
|