2005-2008 RAV4 · Service Manual BODY

REASSEMBLY

Removal / installation · Vehicles built from Aug 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007

CAUTION:
Wear protective gloves. Sharp areas on the seatback frame, seat cushion frame and reclining adjuster may injure your hands.

HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).


1. INSTALL REAR SEAT COVER LH

  1. B135847
    Attach the 2 claws to install the cover.

  1. Install the 2 screws.


2. INSTALL REAR SEATBACK COVER LH

  1. B135846
    Attach the 2 claws to install the cover.

  1. Install the 2 screws.


3. INSTALL REAR NO. 1 SEATBACK COVER

NOTICE:
  1. Be careful not to damage the cover.
  2. When installing the hog rings, avoid wrinkling the cover.

  1. B135848E01
    Using hog ring pliers, install the seatback cover to the seatback pad with 3 new hog rings.

  1. Install the seatback cover (with pad) to the seatback frame.

  1. B060977E01
    Attach the 4 claws to install the 2 headrest supports.

  1. B132487E01
    Lift up the seatback cover and install the 13 hog rings.


4. INSTALL REAR SEATBACK PROTECTOR

  1. B140225
    Install the protector with the 2 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Attach the clip.

  1. B132488E01
    Attach the 2 clips and close the fastening tape.


5. INSTALL REAR SEAT LAP TYPE BELT ASSEMBLY CENTER LH

B130992
  1. Install the belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


6. INSTALL REAR NO. 1 SEATBACK ASSEMBLY LH

  1. B132493
    Install the seatback with the 5 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. B140223
    Attach the 2 clamps and connect the cable to the reclining adjuster.


7. INSTALL REAR SEATBACK LOCK CONTROL LEVER BASE LH

  1. B135842
    Attach the 2 claws to install the lever base.

  1. Install the screw.


8. INSTALL REAR SEAT RECLINING RELEASE LEVER

  1. B140199E01
    Attach the claw to install the release lever.

  1. B140195
    Install the cover with the 2 screws.


9. INSTALL REAR SEAT CUSHION MOULDING LH

  1. B131539
    Attach the 2 claws to install the moulding.

  1. Install the screw.


10. INSTALL REAR SEAT CUSHION REAR MOULDING LH

  1. B132494
    Attach the claw to install the moulding.

  1. Install the screw.


11. INSTALL REAR SEAT REAR BRACKET COVER LH

  1. B135844
    Open the lower part of the seatback cover. Then attach the 4 clips to install the bracket cover.

  1. Install the 2 screws.


12. INSTALL REAR NO. 1 SEAT CUSHION COVER

NOTICE:
  1. Be careful not to damage the cover.
  2. When installing the hog rings, avoid wrinkling the cover.

  1. B140005E01
    Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 3 new hog rings.

  1. B132489E01
    Using hog ring pliers, install the seat cushion cover (with pad) to the seat cushion frame with 29 new hog rings.

  1. B140222
    Attach the 2 hooks.


13. INSTALL REAR NO. 1 SEAT CUSHION ASSEMBLY LH

  1. B132502
    Install the cushion with the 2 bushes and 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. B140219E01
    Install the 2 bolts.


14. INSTALL REAR SEAT INNER BELT ASSEMBLY RH

B138224
  1. Install the belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


15. INSTALL REAR SEAT CUSHION LOWER HINGE COVER LH

  1. B131541
    Attach the 5 claws to install the hinge cover.


16. INSTALL REAR NO. 3 SEAT CUSHION HINGE COVER

  1. B132503
    Attach the 6 claws to install the hinge cover.


17. INSTALL REAR NO. 1 SEAT ARMREST ASSEMBLY LH

  1. B140215
    Install the armrest with the 2 nuts.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }


18. INSTALL REAR SEAT CENTER ARMREST COVER

  1. B140218
    Push the armrest cover in the direction indicated by the arrow in the illustration to attach the 2 claws.

  1. B140216
    Attach the 2 clips to install the armrest cover.


19. INSTALL REAR SEAT CENTER ARMREST ASSEMBLY

  1. B132505
    Install the armrest with the 2 nuts.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }


20. INSTALL CENTER ARMREST HINGE COVER LH

  1. B140214
    Attach the 4 claws to install the hinge cover.


21. INSTALL CENTER ARMREST HINGE COVER RH
  1. Pass the seat lock release strap through the hole in the hinge cover.

  1. Attach the claw to install the hinge cover.

  1. B132496
    Install the 2 screws and 2 rear seatback lock hooks.


22. INSTALL REAR SEAT CENTER HEADREST ASSEMBLY

23. INSTALL REAR SEAT HEADREST ASSEMBLY
← REASSEMBLY (Jan 2007 – Jul 2007)INSTALLATION (Nov 2005 – Dec 2006) →